BD05

C&K BD Series Standard Profile DIP Switches Features/Benefits • Traditional full profile DIP switch • Extended actuator for easy actuation • Open bottom construction allows for solder washing without the need for tape seal • Lead free • RoHS compliant How To Order Complete part numbers for BD Series are shown on pages I–12 through I–13. All switches supplied in “OFF” position. Typical Applications • Address switch for industrial controls I DIP • Logic switching for computers and peripherals • Function controlling for numerous applications Specifications SWITCH FUNCTION: SPST - 1 thru 12 position available (except 11 position). CONTACT RATING: Carry: 100 mA max. @ 50 V DC. Switch: 100 mA max. @ 5 V DC or 25 mA max. @ 25 V DC. MECHANICAL AND ELECTRICAL LIFE: 10,000 make-and-break cycles at full load, each circuit. CONTACT RESISTANCE: Below 50 milliohms typ. initial @ 2-4 V DC 100mA. INSULATION RESISTANCE: 109 ohms min. DIELECTRIC STRENGTH: 500 V RMS min. @ sea level between adjacent terminals. CAPACITANCE: 5pF max. between adjacent terminals. STORAGE & OPERATING TEMPERATURE: -40°C to 85°C. SHOCK: Withstands 20g 11 ms sawtooth waveform with no contact opening greater than 10 microseconds. OPERATING FORCE: ?????????. VIBRATION: No contact opening greater than 10 microseconds and no contact closure when exposed to vibration .06 in DA or 5g, whichever is less, from 10 to 55 Hz, and 10g from 55 to 500 Hz. SOLDERABILITY: Per MIL-STD-202F method 208D, or EIA RS-186E method 9 (1 hour steam aging). PACKAGING: Switches supplied in rigid dispensing tubes in full-tube quantities only: this may effect order quantity. Number of switches per tube varies with model. Switch position 1 denotes pin number 1. All switch actuators in ‘OFF’ position, standard. Materials CASE & COVER: Glass filled polyester (PBT), flame retardant (UL 94V-0). ACTUATOR: Glass filled nylon 6/6, flame retardant, heat stabilized (UL 94V-0) CONTACTS: Gold over nickel over phosphor bronze. TERMINALS: Matte-tin over nickle over phosphor bronze. NOTE: For the latest information regarding RoHS compliance, please go to: www.ittcannon.com/rohs. Note: Specifications and materials listed above are for switches with standard options. For information on specific and custom switches, consult Customer Service Center. Vertical Full Profile DIP .072 (1,83) ACTUATOR TRAVEL .300 (7,62) Ø.038 TYP. (0,97) .100 TYP. (2,54) PART NUMBER NO.POS. 1 2 3 4 5 6 7 8 9 10 12 DIM. ‘A’ .180 (4,57) .280 (7,11) .380 (9,65) .480 (12,19) .580 (14,73) .680 (17,27) .780 (19,81) .880 (22,35) .980 (24,89) 1.080 (27,43) 1.280 (32,51) QUANTITY PER TUBE 115 74 54 43 35 30 26 23 21 19 16 DIM 'A' .380 (9,65) O N 1 2 3 4 5 6 7 8 DIM 'B' .080 TYP. (2,03) .305 (7,75) .040 (1,02) TYP. BD08 .060 TYP. (1,52) .160 TYP. (4,06) BD01 BD02 BD03 BD04 BD05 BD06 BD07 BD08 BD09 BD10 BD12 Schematic .026 (0,66) .090 (2,29) .100 TYP. (2,54) .020 TYP. (0,51) .141 TYP. (3,58) .007 (0,18) SPST .300 (7,62) Dimensions are shown: Inch (mm ) Specifications and dimensions subject to change I-12 www.ittcannon.com C&K BD Series Standard Profile DIP Switches Open Base and AV Right Angle Terminal Style QUANTITY PER TUBE 72 52 42 35 29 26 23 20 18 15 .380 (9,65) 1 2 3 4 5 6 7 8 .125 (3,18) .010 (0,25) .100 (2,54) ON 0.061 TYP. (1,55) DIM.A 0.300 (7,62) 0.050 (1,27) 0.026 (0,66) .090 (2,29) PART NUMBER NO.POS. 2 3 4 5 6 7 8 9 10 12 DIM. ‘A’ .280 (7,11) .380 (9,65) .480 (12,19) .580 (14,73) .680 (17,27) .780 (19,81) .880 (22,35) .980 (24,89) 1.080 (27,43) 1.280 (32,51) BD02AV BD03AV BD04AV BD05AV BD06AV BD07AV BD08AV BD09AV BD10AV BD12AV Schematic I BD08AV DIP .020 TYP. (0,51) SPST NOTE: Box dimensions show difference between AV and AV2 terminal styles. .100 TYP. (2,54) .100 (2,54) .100 TYP. (2,54) .007 (0,18) .320 (8,13) .046 DIA TYP. (1,17ø) Open Base and AV2 Right Angle Terminal Style QUANTITY PER TUBE 72 52 42 35 29 26 23 20 18 15 .380 (9,65) 1 2 3 4 5 6 7 8 ON 0.061 TYP. (1,55) DIM.A 0.050 (1,27) 0.026 (0,66) 0.300 (7,62) .090 (2,29) PART NUMBER NO.POS. 2 3 4 5 6 7 8 9 10 12 DIM. ‘A’ .280 (7,11) .380 (9,65) .480 (12,19) .580 (14,73) .680 (17,27) .780 (19,81) .880 (22,35) .980 (24,89) 1.080 (27,43) 1.280 (32,51) BD02AV2 BD03AV2 BD04AV2 BD05AV2 BD06AV2 BD07AV2 BD08AV2 BD09AV2 BD10AV2 BD12AV2 Schematic BD08AV2 .115 (2,92) .010 (0,25) .100 (2,54) .020 TYP. (0,51) .100 TYP. (2,54) 0.100 (2,54) .007 (0,18) .280 (7,11) SPST NOTE: Box dimensions show difference between AV and AV2 terminal styles. 0.100 TYP. (2,54) 0.046 DIA TYP. (1,17ø) Installation, Soldering and Cleaning All BD Series Standard Profile DIP Switches can be hand soldered or machine soldered without the use of boot, caps, tapes or special attention. Open base washable models have unique design, allowing solvent cleaners and water/detergent solutions to flush and clean the electrical contacts of the contaminants and fluxes. For best results, follow these directions: 1) Wave soldering recommended at 500° F solder temperature. 2) Hand solder using 30 watt small tip iron controlled at 500° F, 10 seconds max./terminal. 3) Open base washable models: Clean flux using forced rinse, high agitation or triple bath cleaning method. DO NOT mask or cover switch in any way during cleaning. Switch is designed for easy solvent flush out. 4) All switch actuators must be in ‘OFF’ position during soldering and cleaning processes. 5) Closed base models with epoxy terminal seal available in even positions, consult factory for details. Dimensions are shown: Inch (mm ) Specifications and dimensions subject to change I-13 www.ittcannon.com