GA240.A126102

Absolute encoders - parallel Shaft with clamping or synchro flange Optical singleturn encoder 13 bit, gray or binary GA240, GA241 - parallel Features – Encoder singleturn / parallel – Optical sensing – Resolution: 13 bit – Clamping flange or synchro flange – Short-circuit proof push-pull outputs – Output release by enable signal – Permanent check of code continuity GA240 with clamping flange Technical data - electrical ratings Voltage supply Consumption w/o load Initializing time (typ.) Interface Steps per turn Absolute accuracy Sensing method Code Code sequence Inputs 10...30 VDC ≤60 mA (24 VDC) 20 ms after power on 13 parallel outputs 8192 / 13 bit ±0.025° Optical Gray or binary CW/CCW coded by connection Control signals UP/DOWN and zero STORE ENABLE Push-pull short-circuit proof DIN EN 61000-6-2 DIN EN 61000-6-4 Self-diagnosis Code continuity check UL approval / E63076 Weight approx. E-connection GA240 - parallel Shaft Flange GA241 - parallel Shaft Flange ø6 mm Synchro flange ø10 mm Clamping flange Reverse polarity protection Yes Technical data - mechanical design Housing Protection DIN EN 60529 Operating speed Starting torque Rotor moment of inertia Admitted shaft load Materials Operating temperature Relative humidity Resistance ø58 mm IP 54 without shaft seal IP 65 with shaft seal ≤10000 rpm (mechanical) ≤6000 rpm (electric) ≤0.015 Nm IP 54 ≤0.03 Nm IP 65 14.5 gcm² ≤20 N axial ≤40 N radial Housing: aluminium Flange: aluminium -25...+85 °C -40...+85 °C (optional) DIN EN 60068-2-6 Vibration 10 g, 16-2000 Hz DIN EN 60068-2-27 Shock 200 g, 6 ms 250 g Connector or cable Subject to modification in technic and design. Errors and omissions excepted. 29/10/2008 Output circuit Interference immunity Emitted interference Diagnostic functions Approval 95 % non-condensing 1 www.baumerivo.com www.baumerivo.com Shaft with clamping or synchro flange Optical singleturn encoder 13 bit, gray or binary Absolute encoders - parallel GA240, GA241 - parallel Part number Clamping flange GA240. 02 E-connection Connector M23, 21-pin, axial Connector M23, 21-pin, radial Cable 21-core, 1 m, axial Cable 21-core, 1 m, radial Synchro flange GA241. 02 E-connection Connector M23, 21-pin, axial Connector M23, 21-pin, radial Cable 21-core, 1 m, axial Cable 21-core, 1 m, radial C0 C1 51 61 C0 C1 51 61 Voltage supply / signals 10 10...30 VDC / gray code push-pull 12 10...30 VDC / binary code push-pull Flange / Shaft 0 Clamping flange / ø10 mm IP 54 A Clamping flange / ø10 mm IP 65 Voltage supply / signals 10 10...30 VDC / gray code push-pull 12 10...30 VDC / binary code push-pull Flange / Shaft 1 Synchro flange / ø6 mm IP 54 B Synchro flange / ø6 mm IP 65 Accessories Connectors and cables (page %S) Z 132.001 Z 132.003 Z 132.005 Z 132.007 Z 119.006 Z 119.013 Z 119.017 Z 119.025 Female connector M27, 21-pin, less cable Female connector M27, 21-pin, 2 m cable Female connector M27, 21-pin, 5 m cable Female connector M27, 21-pin, 10 m cable Eccentric fixing, single Adaptor plate for clamping flange for modification into synchro flange Mounting angle for clamping flange Subject to modification in technic and design. Errors and omissions excepted. 29/10/2008 Mounting accessories for GA240 - parallel (page %S) Adaptor plate for clamping flange, mounting by eccentric fixings (order separately) Eccentric fixing, single Mounting adaptor for synchro flange Bearing flange for encoders with synchro flange Mounting accessories for GA241 - parallel (page %S) Z 119.006 Z 119.015 Z 119.035 2 www.baumerivo.com Absolute encoders - parallel Shaft with clamping or synchro flange Optical singleturn encoder 13 bit, gray or binary GA240, GA241 - parallel Terminal significance UB GND Outputs D0-D12 DATAVALID Encoder voltage supply. Encoder ground connection relating to UB. 13 parallel output signals. Diagnostic output. An error warning is given at level Low. Important: Interferences must be filtered by the downstram electronics. Input for setting a zero point anywhere within the programmed encoder resolution. The zero setting operation is triggered by a High impulse and has to be in line with the selected direction of rotation (UP/DOWN). Connect to GND after setting operation for maximum interference immunity. Impulse duration >100 ms. UP/DOWN counting direction input. This input is standard on High. UP/DOWN means ascending output data with clockwise shaft rotation when looking at flange. UP/DOWN-Low means ascending values with counterclockwise shaft rotation when looking at flange. Input for activating the output drivers that are triggered by input level Low. Upon being on High (or less potential) the output drivers switch to high-impedance (Tristate). Input for output data storage. Upon a Low input level the encoder data are stored in the intermediate memory. Upon being on High (or less potential) the current encoder position data are switched to the output drivers. This line must be applied for reliable data readout in binary code. Terminal assignment Connector Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 Pin 7 Pin 8 Pin 9 Pin 10 Pin 11 Pin 12 Pin 13 Pin 14 Pin 15 Pin 16 Pin 17 Pin 18 Pin 19 Pin 20 Pin 21 Core colour violet white/brown white/green white/yellow white/grey white/pink white/blue white/red white/black brown/green brown/grey brown/pink green/grey blue blue/yellow brown pink red red/yellow yellow Assignment Output D0 Output D1 Output D2 Output D3 Output D4 Output D5 Output D6 Output D7 Output D8 Output D9 Output D11 Output D12 – GND DATAVALID UP/DOWN STORE UB Zero setting ENABLE Zero setting brown/yellow Output D10 UP/DOWN ENABLE STORE 13 1 12 14 2 15 3 11 20 21 16 4 10 19 9 18 17 5 876 Trigger level Control inputs Input level High Input level Low Input resistance Parallel outputs Output level High Output level Low Load High Load Low Tristate Input circuit >0.7 UB UB -3.5 V (I = -20 mA)