N142.113AA01

Spindle Position Displays Hollow shaft max. ø25 mm, automatic format alignment Display LCD two lines, interface RS485 N 142 Features – Motive spindle position display – Absolute multiturn measuring system – Display: LCD backlit, two lines – Actual value and target display – Hollow shaft ø20 mm / ø25 mm – Interface RS485 – Resolution: 2304 steps/revolution ±4096 revolutions – Two operating keys for format alignment touch by touch N 142 with cable output Technical data - electrical ratings Voltage supply Current consumption Display Measuring principle Measuring range Steps per turn Number of turns Spindle pitch Interface Data memory 24 VDC ±10 % ≤40 mA LCD, 7-segment display, 2-lines, backlit Absolute multiturn measuring system -999,99...+9999,99 mm -99.999...+999.999 inch 2304 4096 / 12 bit ≤23 mm RS485 (ASCII protocol) Parameter buffer: EEPROM Current value buffer: >10 years by integrated 3 V lithium battery Display position horizontal/ vertical Measuring unit mm/inch Counting direction Spindle pitch Spindle tolerance Positioning direction Direction arrows Tolerance window Round up/down Two softkeys for format alignment Direct motor connection to N 142 by motor cable Protection class II Overvoltage category II Pollution degree 2 DIN EN 61000-6-3 DIN EN 61000-6-2 UL/cUL Operation / keypad Housing type Dimensions W x H x L Mounting Weight approx. Material Technical data - mechanical design Hollow shaft Operating speed Protection DIN EN 60529 Operating temperature Storing temperature Relative humidity Torque support E-connection ø20 mm, ø25 mm ≤600 rpm (short-term) IP 65 -10...+50 °C -20...+70 °C 80 % non-condensing Torque pin provided at housing - Cable output (30 cm) with male/female connector M16, 5-pin - Motor cable with female connector M16, 12-pin Membrane with two keys Surface-mount with hollow shaft Surface-mount with hollow shaft 200 g Polycarbonate black, UL 94V-0 Subject to modification in technic and design. Errors and omissions excepted. 30/10/2008 Programmable parameters 56 x 100 x 62.5 mm Motive positioning Standard DIN EN 61010-1 Emitted interference Interference immunity Approval 1 www.baumerivo.com www.baumerivo.com Hollow shaft max. ø25 mm, automatic format alignment Display LCD two lines, interface RS485 Spindle Position Displays N 142 Part number N 142. 1 3 A 01 Hollow shaft A Hollow shaft ø25 mm B Hollow shaft ø20 mm Display A Inclined Voltage supply 3 24 VDC E-connection 1 Cable output M16, motor cable 0.5 m 2 Cable output M16, motor cable 1.5 m Interface 1 RS485 Accessories Connectors and cables (page %S) Z 165.A01 Z 165.AW1 Z 165.B01 Z 165.D05 Z 165.S01 Z 165.V01 Adaptor cable between cable connector M16 and female M8, 1 m Cable connector M16, 5-pin, less cable with integrated terminating resistor 120 Ω Mating connector M16, 5-pin, less cable Data and supply cable M16, Master to N 140, N 141 and N 142, 5 m Cable connector M16, 5-pin, less cable Coupling cable between M16 and M16, 1 m Subject to modification in technic and design. Errors and omissions excepted. Description multiconDrive represents a simplified and very efficient, reasonably priced system for automatic format alignment. With multiconDrive the spindle position displays communicate directly with EC motors. Every spindle position display is connected to the corresponding motor by a separate cable output providing the motor without delay with the signals “clockwise”, “counterclockwise”, “rotation speed” for switchover to high/low speed. The spindle position display provides two keys for clockwise and counterclockwise direction used during the first editing operation. The key makes the motor moving into the requested direction. A soft touch results in a defined STEP. Thus, new spindle positions can be edited under direct visual check of the operator with an accuracy of ±1/100 mm. Shaft position parameters once set can be filed as profile in the control. The serial interface enables network of maximum 32 spindle position displays with PC or PLC. For complete solutions N 242 memory controller as operating and memory terminal is available. Up to 100 format profiles can be stored by teach-in. The respective position parameters can be retransmitted at any time as target to the respecitve spindle position displays to release automatic format alignment cycles. 2 www.baumerivo.com 30/10/2008 Spindle Position Displays Hollow shaft max. ø25 mm, automatic format alignment Display LCD two lines, interface RS485 N 142 Terminal assignment SPA connector and female connector, 5-pin Connector Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Assignment Sensor supply +24 V Sensor supply 0 V – Tx/Rx+, RS485 Tx/Rx-, RS485 M16 connector 4 5 3 2 1 1 5 2 3 4 Motor connector, 12-pin Connector Pin A Pin B Pin C Pin D Pin E Assignment – Motor left Motor right Speed – Key 1 external Key 2 external – – Error signal Speed GND M16 male connector CL D E B A M FG K J H M16 female connector Pin F Pin G Pin H Pin J Pin K Pin L Pin M Circuit diagram supply voltage release counterclockwise release clockwise Enable n.c. 1 2 3 4 5 6 7 8 24 V 0V IN 1 output IN 1 input IN 2 output IN 2 input (logic 24 V) OUT 1 IN 1 (left) IN 2 (right) IN 4 (speed) 24 V n.c. n.c. AI- (0...10 V) AI+ (0...10 V) OUT 3 (fault) IN 3 (speed) 0V A B C D E F G H J K Error L M M Motor SPA 3 www.baumerivo.com www.baumerivo.com 30/10/2008 Subject to modification in technic and design. Errors and omissions excepted. Motor left Motor right Speed n.c. key 1 external key 2 external n.c. n.c. Error signal Speed GND Hollow shaft max. ø25 mm, automatic format alignment Display LCD two lines, interface RS485 Spindle Position Displays N 142 Dimensions Hollow shaft Ø25 mm 7 Fixing pin for bore Ø10 mm 58.5 40 ±0.2 Hollow shaft Ø20 mm 100 M5 25 H7 7) (20 H Ø37 Ø37 M5 4 8.5 M16 male connector 8 20° 6 10 1 62.5 21.5 M16 female connector 22 56 17 M16 male connector / motor Ø37 4 www.baumerivo.com 30/10/2008 Subject to modification in technic and design. Errors and omissions excepted.