N150.113AA01

Spindle Position Displays Hollow shaft max. ø14 mm, manual format alignment Display LCD two lines, interface RS485 N 150 Features – Manual spindle position display – Absolute multiturn measuring system – Display: LCD backlit, two lines – Actual value and target display – Hollow shaft max. ø14 mm – Interface RS485 – Resolution: 1440 steps/revolution ±4096 revolutions N 150 with connector output Technical data - electrical ratings Voltage supply Current consumption Display Measuring principle Measuring range Steps per turn Number of turns Spindle pitch Interface Data memory 24 VDC ±10 % ≤30 mA LCD, 7-segment display, 2-lines, backlit Absolute multiturn measuring system -99.99...+999.99 mm -9.999...+99.999 inch 1440 4096 / 12 bit ≤14 mm RS485 (ASCII protocol) Parameter buffer: EEPROM Current value buffer: >10 years by integrated 3 V lithium battery Display position horizontal/ vertical Measuring unit mm/inch Spindle pitch Counting direction Spindle tolerance Positioning direction Direction arrows Tolerance window Round up/down Protection class II Overvoltage category II Pollution degree 2 DIN EN 61000-6-3 DIN EN 61000-6-2 UL/cUL Housing type Dimensions W x H x L Mounting Weight approx. Material Technical data - mechanical design Hollow shaft Operating speed Protection DIN EN 60529 Operating temperature Storing temperature Relative humidity Torque support E-connection ø14 mm ≤600 rpm (short-term) IP 65 -10...+50 °C -20...+70 °C 80 % non-condensing Torque pin provided at housing - Male/female connector M8, 4-pin - Cable output (30/15 cm) with male/female connector M8, 4-pin Surface-mount with hollow shaft 37 x 75 x 45 mm 120 g Polyamide black, UL 94V-0 Subject to modification in technic and design. Errors and omissions excepted. 30/10/2008 Programmable parameters Surface-mount with hollow shaft Standard DIN EN 61010-1 Emitted interference Interference immunity Approval 1 www.baumerivo.com www.baumerivo.com Hollow shaft max. ø14 mm, manual format alignment Display LCD two lines, interface RS485 Spindle Position Displays N 150 Part number N 150. 1 3 A 01 Description N 150 spindle position display supports the editing engineer in manual spindle positioning. The principal benefits of the new electronic spindle position display are saving time in machine setup and editing as well as eliminating errors when aligning formats to new position values. The absolute measuring system captures any change in position even in powerless state. The backlit LCD display provides the editing engineer with all necessary information for efficient editing of new spindle positions. The two-line display shows both current value and target. A little arrow signalizes the editing engineer the direction the spindle must be turned to get to the new position. RS485 serial interface enables network of maximum 32 spindle position displays to PC or PLC. For complete solutions also memory controllers serving as decentralized operating and memory terminals are available. Up to 100 format profiles can be stored by teach-in. Upon request the desired profile is recalled upon pressing a button and and retransmitted to every spindle position display and shown as target. Hollow shaft A Hollow shaft ø14 mm Display A Inclined B Horizontal at front Voltage supply 3 24 VDC E-connection 0 Connector output M8 1 Cable output M8 Interface 1 RS485 Accessories Connectors and cables (page %S) Z 178.A01 Z 178.AW1 Z 178.B01 Z 178.D05 Z 178.S01 Z 178.V01 Adaptor cable between cable connector M8 and female M16, 1 m Cable connector M8, 4-pin, less cable with integrated terminating resistor 120 Ω Mating connector M8, 4-pin, less cable Data and supply cable M8, Master to N 150 and N 155, 5 m Cable connector M8, 4-pin, less cable Coupling cable 1 m between M8 and M8 2 www.baumerivo.com 30/10/2008 Subject to modification in technic and design. Errors and omissions excepted. Spindle Position Displays Hollow shaft max. ø14 mm, manual format alignment Display LCD two lines, interface RS485 N 150 Terminal assignment Connector Pin 1 Pin 2 Pin 3 Pin 4 Assignment Tx/Rx-, RS485 Tx/Rx+, RS485 Sensor supply +24 V Sensor supply 0 V M8 connector 1 3 2 4 2 4 1 3 M8 female connector Dimensions Optional display position 75 ° 4.8 Torque pin 6 0.5x 45° Connect or output Cable output 22 ø14H7 75 ø6h9 ø20 28 20.5 2:1 A 300 M8 female connector 16 Pin M4 13 26 37 31.8 6.5 45 Seal 14 1 13 52 A 60 150 M8 connector 30.15 12.5 10 Connector Female connector ø12 ø12 3 www.baumerivo.com www.baumerivo.com 30/10/2008 Subject to modification in technic and design. Errors and omissions excepted. Hollow shaft max. ø14 mm, manual format alignment Display LCD two lines, interface RS485 Spindle Position Displays N 150 4 www.baumerivo.com 30/10/2008 Subject to modification in technic and design. Errors and omissions excepted.