N152.123BA01

Spindle Position Displays Hollow shaft max. ø14 mm, automatic format alignment Display LCD two lines, interface RS485 N 152 Features – Motive spindle position display – Absolute multiturn measuring system – Display: LCD backlit, two lines – Actual value and target display – Hollow shaft max. ø14 mm – Interface RS485 – Resolution: 1440 steps/revolution ±4096 revolutions – Two operating keys for format alignment touch by touch N 152 with cable output Technical data - electrical ratings Voltage supply Current consumption Display Measuring principle Measuring range Steps per turn Number of turns Spindle pitch Interface Data memory 24 VDC ±10 % ≤40 mA LCD, 7-segment display, 2-lines, backlit Absolute multiturn measuring system -99.99...+999.99 mm -9.999...+99.999 inch 1440 4096 / 12 bit ≤14 mm RS485 (ASCII protocol) Parameter buffer: EEPROM Current value buffer: >10 years by integrated 3 V lithium battery Display position horizontal/ vertical Measuring unit mm/inch Spindle pitch Counting direction Spindle tolerance Positioning direction Direction arrows Tolerance window Round up/down Two softkeys for format alignment Direct motor connection to N 152 by motor cable Protection class II Overvoltage category II Pollution degree 2 DIN EN 61000-6-3 DIN EN 61000-6-2 UL/cUL Operation / keypad Housing type Dimensions W x H x L Mounting Weight approx. Material Technical data - mechanical design Hollow shaft Operating speed Protection DIN EN 60529 Operating temperature Storing temperature Relative humidity Torque support E-connection ø14 mm ≤600 rpm (short-term) IP 65 -10...+50 °C -20...+70 °C 80 % non-condensing Torque pin provided at housing - Cable output (15 cm) with male connector M8, 4-pin - Motor cable with female connector M16, 12-pin Membrane with two keys Surface-mount with hollow shaft 37 x 75 x 45 mm 120 g Polyamide black, UL 94V-0 Subject to modification in technic and design. Errors and omissions excepted. 11/11/2008 Programmable parameters Surface-mount with hollow shaft Motive positioning Standard DIN EN 61010-1 Emitted interference Interference immunity Approval 1 www.baumerivo.com www.baumerivo.com Hollow shaft max. ø14 mm, automatic format alignment Display LCD two lines, interface RS485 Spindle Position Displays N 152 Part number N 152. 1 3 A 01 Description multiconDrive represents a simplified and very efficient, reasonably priced system for automatic format alignment. With multiconDrive the spindle position displays communicate directly with EC motors. Every spindle position display is connected to the corresponding motor by a separate cable output providing the motor without delay with the signals “clockwise”, “counterclockwise”, “rotation speed” for switchover to high/low speed. The spindle position display provides two keys for clockwise and counterclockwise direction used during the first editing operation. The key makes the motor moving into the requested direction. A soft touch results in a defined STEP. Thus, new spindle positions can be edited under direct visual check of the operator with an accuracy of ±1/100 mm. Shaft position parameters once set can be filed as profile in the control. The serial interface enables network of maximum 32 spindle position displays with PC or PLC. For complete solutions N 242 memory controller as operating and memory terminal is available. Up to 100 format profiles can be stored by teach-in. The respective position parameters can be retransmitted at any time as target to the respecitve spindle position displays to release automatic format alignment cycles. Hollow shaft A Hollow shaft ø14 mm Display A Inclined B Horizontal at front Voltage supply 3 24 VDC E-connection 1 Cable output M8, motor cable 0.5 m 2 Cable output M8, motor cable 1.5 m Interface 1 RS485 Accessories Connectors and cables Z 178.A01 Z 178.AW1 Z 178.B01 Z 178.D05 Z 178.S01 Z 178.V01 Z 178.Y01 Adaptor cable between cable connector M8 and female M16, 1 m Cable connector M8, 4-pin, less cable with integrated terminating resistor 120 Ω Mating connector M8, 4-pin, less cable Data and supply cable M8, Master to N 150 and N 155, 5 m Cable connector M8, 4-pin, less cable Coupling cable 1 m between M8 and M8 2 www.baumerivo.com 11/11/2008 Subject to modification in technic and design. Errors and omissions excepted. Y-junction M8, 4-pin, with cable Spindle Position Displays Hollow shaft max. ø14 mm, automatic format alignment Display LCD two lines, interface RS485 N 152 Terminal assignment SPA – connector, 4-pin M8 connector Assignment Pin 1 Pin 2 Pin 3 Pin 4 Tx/Rx–, RS485 Tx/Rx+, RS485 Sensor supply +24 V Sensor supply 0 V M8 connector 1 3 2 4 Motor connector, 12-pin Connector Pin A Pin B Pin C Pin D Pin E Pin F Pin G Pin H Pin J Pin K Pin L Pin M Assignment – Motor left Motor right Speed – – – – – Error signal Speed GND M16 male connector CL D E B A M FG K J H Circuit diagram supply voltage release counterclockwise release clockwise Enable n.c. 1 2 3 4 5 6 7 8 24 V 0V IN 1 output IN 1 input IN 2 output IN 2 input (logic 24 V) OUT 1 IN 1 (left) IN 2 (right) IN 4 (speed) 24 V n.c. n.c. AI- (0...10 V) AI+ (0...10 V) OUT 3 (fault) IN 3 (speed) 0V A B C D E F G H J K Error L M M Motor SPA 3 www.baumerivo.com www.baumerivo.com 11/11/2008 Subject to modification in technic and design. Errors and omissions excepted. Motor left Motor right Speed n.c. n.c. n.c. n.c. n.c. Error signal Speed GND Hollow shaft max. ø14 mm, automatic format alignment Display LCD two lines, interface RS485 Spindle Position Displays N 152 Dimensions Optional display position 75 ° 4.8 Torque pin 6 0.5x 45° 22 ø14H7 75 ø20 28 20.5 2:1 Pin M4 Seal 6.5 37 31.8 30.15 12.5 45 1 M8 mal e connector M16 male connector / motor ø6h9 4 www.baumerivo.com 11/11/2008 Subject to modification in technic and design. Errors and omissions excepted.