N153

Spindle Position Displays Hollow shaft max. ø14 mm, with infrared interface Format alignment by power tool, interface RS485 N 153 Features – Infrared interface for format alignment by power tool – Absolute multiturn measuring system – Display: LCD backlit, two lines – Actual value and target display – LED status display – Interface RS485 – Resolution: 1440 steps/revolution ±4096 revolutions – Two operating keys for format alignment touch by touch N 153 with cable output Technical data - electrical ratings Voltage supply Current consumption Display Measuring principle Measuring range Steps per turn Number of turns Spindle pitch Interface Data memory 24 VDC ±10 % ≤40 mA LCD, 7-segment display, 2-lines, backlit Absolute multiturn measuring system -99.99...+999.99 mm -9.999...+99.999 inch 1440 4096 / 12 bit ≤14 mm RS485 (ASCII protocol) Parameter buffer: EEPROM Current value buffer: >10 years by integrated 3 V lithium battery Display position horizontal/ vertical Measuring unit mm/inch Counting direction Spindle pitch Spindle tolerance Positioning direction Direction arrows Tolerance window Round up/down Two softkeys for format alignment Connected to power tool by infrared interface Protection class II Overvoltage category II Pollution degree 2 DIN EN 61000-6-3 DIN EN 61000-6-2 UL/cUL Operation / keypad Housing type Dimensions W x H x L Mounting Weight approx. Material Technical data - mechanical design Hollow shaft Operating speed Protection DIN EN 60529 Operating temperature Storing temperature Relative humidity Torque support E-connection ø14 mm ≤600 rpm (short-term) IP 65 -10...+50 °C -20...+70 °C 80 % non-condensing Torque pin provided at housing - Male/female connector M8, 4-pin - Cable output (30/15 cm) with male/female connector M8, 4-pin Membrane with two keys Surface-mount with hollow shaft Surface-mount with hollow shaft 120 g Polyamide black, UL 94V-0 Subject to modification in technic and design. Errors and omissions excepted. 30/10/2008 Programmable parameters 37 x 75 x 45 mm Motive positioning Standard DIN EN 61010-1 Emitted interference Interference immunity Approval 1 www.baumerivo.com www.baumerivo.com Hollow shaft max. ø14 mm, with infrared interface Format alignment by power tool, interface RS485 Spindle Position Displays N 153 Part number N 153. 1 3 A A 01 Description multicon AccuDrive is an economical system for mobile, motive format alignment. By AccuDrive positioning of shafts to the desired format is quick, accurate and less fussy hand crank operations. Saving setup times and avoiding editing errors are consequently the most convincing arguments. The electrically commutated professional power tool ASMIR serves as mobile actuator that communicates with N 153 spindle position displays by infrared interface. Red and green status LEDs provided at the position display indicate the operator which shafts require alignment. A flashing LED indicates the positioning order. The power tool is a vital help in aligning the respective shafts to the new format. Select the desired positioning direction by aid of the two pushbuttons provided at the power tool. Press and hold the start button to start the positioning operation at slow speed with increasing acceleration. This way, the operator is able to proceed the positioning operation in direct sight with an accuracy of ±1/100 mm. Any shaft positions once effected can be filed under a parameter profile in the control to be recalled any time. By serial interface maximum 32 spindle position displays may be networked to PC or PLC. Through solutions are realized by memory controller N 242 as memory and operating terminal where max. 100 format profiles can be entered and saved by Teach-in. Hollow shaft A Hollow shaft ø14 mm Display A Inclined Voltage supply 3 24 VDC E-connection 0 Connector output M8 1 Cable output M8 Interface 1 RS485 Accessories Connectors and cables (page %S) Z 178.A01 Z 178.AW1 Z 178.B01 Z 178.D05 Z 178.S01 Z 178.V01 Adaptor cable between cable connector M8 and female M16, 1 m Cable connector M8, 4-pin, less cable with integrated terminating resistor 120 Ω Mating connector M8, 4-pin, less cable Data and supply cable M8, Master to N 150 and N 155, 5 m Cable connector M8, 4-pin, less cable Coupling cable 1 m between M8 and M8 2 www.baumerivo.com 30/10/2008 Subject to modification in technic and design. Errors and omissions excepted. Spindle Position Displays Hollow shaft max. ø14 mm, with infrared interface Format alignment by power tool, interface RS485 N 153 Terminal assignment SPA – connector and female connector, 4-pin Connector Pin 1 Pin 2 Pin 3 Pin 4 Assignment Tx/Rx-, RS485 Tx/Rx+, RS485 Sensor supply +24 V Sensor supply 0 V M8 connector 1 3 2 4 2 4 1 3 M8 female connector Dimensions 75 ° 4.8 Torque pin 6 0.5x 45° ø14H7 IR-Diode ø6h9 28 2:1 StatusLED A 300 M8 female connector Connect or output Cable output 75 22 20.5 16 Pin M4 13 26 37 31.8 6.5 45 ø20 Seal 14 1 13 52 A 60 150 M8 connector 10 Connector Female connector ø12 ø12 3 www.baumerivo.com www.baumerivo.com 30/10/2008 Subject to modification in technic and design. Errors and omissions excepted. 30.15 12.5 Hollow shaft max. ø14 mm, with infrared interface Format alignment by power tool, interface RS485 Spindle Position Displays N 153 4 www.baumerivo.com 30/10/2008 Subject to modification in technic and design. Errors and omissions excepted.