N214.302AX01

Totalizers electronic Large impulse counters and position displays Display LED, 6-digits, programmable N 214 Features – Totalizer and position display – Display 6-digits – Set value, scaling factor, momentary signal duration and operating mode programmable – Connection: Incremental encoder or digital sensors – Interface RS232, RS422, RS485 N 214 - Totalizer Technical data - electrical ratings Voltage supply 115/230 VAC ±10 % (50/60 Hz) 24/48 VAC ±10 % (50/60 Hz) 12...30 VDC 7 VA, 5 W 12...26 VDC / max. 100 mA LED, 7-segment display 6-digits 14 mm Totalizer Difference counter A - B Parallel counter A + B Position display 0.0001...9999.99 Adding or subtracting A-B (difference counting) A+B total (parallel counting) Up/Down A 90° B phase evaluation 3 Hz, 25 Hz, 10 kHz programmable -99 999...+999 999 >10 years in EEPROM Button and electric Yes, electric (keylock) Optocoupler Potential-free change-over contact 0.01...9.99 s RS232, RS422, RS485 Protection class II Overvoltage category II Pollution degree 2 DIN EN 61000-6-3 DIN EN 61000-6-2 Technical data - mechanical design Operating temperature Storing temperature Relative humidity E-connection Core cross-section Protection DIN EN 60529 Operation / keypad Housing type Dimensions W x H x L Installation depth Mounting Cutout dimensions Materials Weight approx. 0...+50 °C -20...+70 °C 80 % non-condensing Plug-in screw terminals 1.5 mm² IP 65 face with seal Membrane with softkeys 96 x 48 x 124 mm 124 mm Clip frame 92 x 45 mm (+0.6) Housing: Makrolon 6485 (PC) Keypad: Polyester 350 g (AC), 250 g (DC) Subject to modification in technic and design. Errors and omissions excepted. 30/10/2008 Technical data - electrical ratings Programmable parameters Approvals Decimal point Sensor logic, scaling factor Count mode, measuring units UL/cUL, CE conform Power consumption Sensor supply Display Number of digits Digit height Function Scaling factor Count modes Built-in housing Counting frequency Measuring range Data memory Reset Keylock Outputs electronic Outputs relay Output holding time Interfaces Standard DIN EN 61010-1 Emitted interference Interference immunity 1 www.baumerivo.com www.baumerivo.com Large impulse counters and position displays Display LED, 6-digits, programmable Totalizers electronic N 214 Part number N 214. AX01 Voltage supply 1 24 / 48 VAC 2 115 / 230 VAC 3 24 VDC Outputs 0 Without relay 1 Relay and optocoupler outputs 0 1 2 3 Interface Without interface RS485 RS422 RS232 Block circuit diagram Voltage supply + Signal input A B 2 3 4 5 Sensor supply + Output 6 7 8 9 14 Interface RS485 A 90° B 10 Totalizer with start count scaling factor 11 Output 20 21 22 SC- / 0 SC- / 0 Reset Stop/Hold T,R- T,R+ 15 TxD+ 16 TxD- 17 RxD+ 18 RxD- 19 TxD RxD 16 18 Interface RS422 Interface RS232 GND 19 Connection diagram Trigger level 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 RxD+ TxDTxD+ RxD- Comparator inputs Inputs Input level Input level Low Input level High Supply voltage Input circuit PNP- / NPN-logic Programmable 0...2 VDC 3...40 VDC 3 kΩ Output circuit 250 VAC / 110 VDC 1A 5 ms Output circuit Optocoupler not short-circuit proof 40 V 15 mA Subject to modification in technic and design. Errors and omissions excepted. 30/10/2008 SC- / 0 Output max. 250V terminal - terminal / - terminal RS422 GND RxD RS232 TxD 15 14 13 12 11 10 T,R+ T,R- 9 8 7 Track B 6 Track A 5 +24V 4 3 2 1 Input resistance Relay output Switching voltage max. Switching current max. Switching capacity max. Relay responding time Electronic output Switching voltage max. Switching current max. RS485 Output Reset SC- / 0 Stop Count Sensor supply 0V 150 VA / 30 W Dimensions 96 123.75 7 48 109 19.75 1-10 2 www.baumerivo.com