IX6R11S3T/R

IX6R11 600 Volt, 6 Ampere High & Low-side Driver for N-Channel MOSFETs and IGBTs Features General Description • Floating High Side Driver with boot-strap Power supply along with a Low Side Driver. • Fully operational to 600V • ± 50V/ns dV/dt immunity • Gate drive power supply range: 10 - 35V • Undervoltage lockout for both output drivers • Separate Logic power supply range: 3.3V to VCL • Built using the advantages and compatibility of CMOS and IXYS HDMOSTM processes • Latch-Up protected over entire operating range • High peak output current: 6A • Low output impedance • Low power supply current • Immune to negative voltage transients The IX6R11 Bridge Driver for N-channel MOSFETs and IGBTs with a high side and low side output, whose input signals reference the low side. The High Side driver can control a MOSFET or IGBT connected to a positive bus voltage up to 600V. The logic input stages are compatible with TTL or CMOS, have built-in hysteresis and are fully immune to latch up over the entire operating range. The IX6R11 can withstand dV/dt on the output side up to ± 50V/ns. Ordering Information The IX6R11 is available in the 14-Pin DIP, the 16-Pin SOIC, and the heat-sinkable 18-Pin SOIC CooltabTM packages. Applications • • • • • • Driving MOSFETs and IGBTs in half-bridge circuits High voltage, high side and low side drivers Motor Controls Switch Mode Power Supplies (SMPS) DC to DC Converters Class D Switching Amplifiers Part Number Package Type IX6R11P7 IX6R11S3 IX6R11S6 14-Pin DIP 16-Pin SOIC 18-Pin SOIC Warning: The IX6R11 is ESD Sensitive Precaution: when performing the High-Voltage tests, adequate safety precautions should be taken! *Operational voltage rating of 600V determined in a typical half-bridge circuit configuration (refer to Figure 10 and Figure 11). Operational voltage in other circuit configurations may vary. Figure 1. Typical Circuit Connection IX6R11S6 IX6R11S3 Up to 600V © 2007 IXYS CORPORATION All rights reserved DS99037G(10/07) IX6R11 Figure 2 - IX6R11 Functional Block Diagram VDD VCH Low to HIN HIN HIN VCH High OUT RST IN Gate Current Output HGO UVCC Detect DG HS HS Isolated High Side VCL VDD LIN VCL Low to High Side Delay Equalizer and Shutdown Gate Current Output Shutdown Logic ENB LGO UVCC Detect DG DG LS 1Ω LS Pin Description and Configuration FUNCTION DESCRIPTION Logic Supply Positive power supply for chip CMOS functions HS Input High side input signal, TTL or CMOS compatible; HGO in phase LS Input Low side input signal, TTL or CMOS compatible; LGO in phase Enable Chip enable, active low. When driven high, both outputs go low Ground Logic reference ground Supply Voltage High side power supply, referenced to HS Output High side driver output Return High side voltage return pin Supply Voltage Low side power supply, referenced to LS Output Low side driver output Ground Low side voltage return pin 16-PIN SOIC N/C HGO 7 9 VDD VCH 6 10 HIN HS 5 11 ENB N/C 4 12 LIN VCL 3 13 DG LS 2 14 NC LGO 1 IX6R11P7 8 Cooltab is a trademark of IXYS Corporation IXYS reserves the right to change limits, test conditions, and dimensions. 18-PIN SOIC w/CooltabTM IX6R11S6 14-PIN DIP IX6R11S3 SYMBOL VDD HIN LIN ENB DG VCH HGO HS VCL LGO LS IX6R11 Absolute Maximum Ratings Symbol Definition Min Max Units VCH High side floating supply voltage -0.3 +35 V VHS High side floating supply offset Voltage -200 +600 V VHGO High side floating output voltage VHS-0.3 VCH+0.3 V VCL Low side fixed supply voltage -0.3 35 V VLGO Low side output voltage -0.3 VCL+0.3 V VDD Logic supply voltage -0.3 VCL+0.3 V VDG Logic supply offset voltage VLS-3.8 VLS+3.8 V VIN Logic input voltage(HIN & LIN) VLS-0.3 VCL+0.3 V dVS/dt Allowable offset supply voltage transient PD Package power dissipation@ TA ≤ 25C 1.25 W PD Package power dissipation@ TC ≤ 25C 2.5 W RTHJA Thermal resistance, junction-to-ambient 100 K/W Recommended Operating Conditions Symbol Definition 50 V/ns Min Max Units VHS+10 VHS+20 V VCH High side floating supply absolute voltage VHS High side floating supply offset voltage -20 +600 V VHGO High side floating output voltage VHS VCH+20 V VCL Low side fixed supply voltage 10 20 V VLGO Low side output voltage 0 VCC V VDD Logic supply voltage VDG+3 VDG+VCL V VDG Logic supply offset voltage VLS-0.5 VLS+0.5 V VIN Logic input voltage(HIN, LIN, ENbar) VDG VDD V TA Ambient Temperature -40 125 o © 2007 IXYS CORPORATION All rights reserved C IX6R11 Dynamic Electrical Characteristics* VCL = VCH = VDD = +15V, Cload = 5nF, and VDG = VLS unless otherwise specified. The dynamic electrical characteristics are measured using Figure 7. Symbol Definition Test Conditions ton Turn-on propagation delay VHS= 0V 120 160 ns toff Turn-off propagation delay VHS= 600V 94 125 ns tenb Device not enable delay 110 140 ns tr Turn-on rise time 25 35 ns tf Turn-off fall time 17 25 ns tdm Delay matching, HS & LS turn-on/off 25 50 ns Static Electrical Characteristics Symbol Definition Test Conditions VINH Logic “1” input voltage, HIN, LIN, ENB VDD= VCL= 15V VINL Min Typ Max Units Min Typ Max Units 9.5 V Logic “0” input voltage, HIN, LIN, ENB VDD= VCL= 15V 0 6 V VHLGO // VHHGO High level output voltage, VCH-VHGO or VCL-VLGO IO= 0A 0.1 V VLLGO // VLHGO Low level output voltage, VHGO or VLGO IO= 0A 0.1 V IHL HS to LS bias current. VHS= VCH= 600V IQHS Quiescent VCH supply current VIN= 0V or VDD = 15V 1 3 mA IQLS Quiescent VCL supply current VIN= 0V or VDD = 15V 1 3 mA IQDD Quiescent VDD supply current VIN= 0V or VDD = 15V 15 30 µA IIN+ Logic “1” input bias current VIN= VDD 20 40 µA IIN- Logic “0” input voltage VIN= 0V 1 µA VCHUV+ VCH supply undervoltage positive going threshold. 9.7 V VCHUV- VCH supply undervoltage negative going threshold. VCLUV+ VCL supply undervoltage positive going threshold VCLUV- µA 170 7.5 8.6 7 8.2 9.4 V 7.4 8.5 9.6 V VCL supply undervoltage negative going threshold. 7 8.2 9.4 V IGO+ HS or LS Output high short circuit current; V 4 6 IGO- HS or LS Output low short circuit current; V = 15V, VIN= 15V, PW