LCB110
350V, 120mA Single-Pole,
Normally Closed Relay
INTEGRATED CIRCUITS DIVISION
Parameter
Blocking Voltage
Load Current
On-Resistance (max)
Ratings
350
120
35
Units
VP
mArms / mADC
Its optically coupled outputs, which use the patented
OptoMOS architecture, are controlled by a highly
efficient infrared LED.
Features
•
•
•
•
•
•
•
Description
The LCB110 is a single-pole, normally closed
(1-Form-B) relay that uses optically coupled MOSFET
technology to provide 3750Vrms of input to output
isolation.
3750Vrms Input/Output Isolation
Low Drive Power Requirements
FCC Compatible
VDE Compatible
No EMI/RFI Generation
Small 6-Pin Package
Surface Mount Tape & Reel Version Available
The LCB110 has low on-resistance and is well suited
for most applications requiring a normally closed relay.
Approvals
• UL Recognized Component: File # E76270
• CSA Certified Component: Certificate # 1175739
• TUV EN 62368-1: Certificate # B 082667 0008
Applications
• Telecommunications
• Telecom Switching
• Tip/Ring Circuits
• Modem Switching (Laptop, Notebook, Pocket Size)
• Hook Switch
• Dial Pulsing
• Ground Start
• Ringing Injection
• Instrumentation
• Multiplexers
• Data Acquisition
• Electronic Switching
• I/O Subsystems
• Meters (Watt-Hour, Water, Gas)
• Medical Equipment-Patient/Equipment Isolation
• Security
• Industrial Controls
Ordering Information
Part #
LCB110
LCB110S
LCB110STR
Description
6-Pin DIP (50/Tube)
6-Pin Surface Mount (50/Tube)
6-Pin Surface Mount (1000/Reel)
* For other packaging options consult factory.
Pin Configuration
AC/DC Configuration
+ Control
– Control
N/C
1
6
2
5
3
4
Load
Do Not Use
Load
DC Only Configuration
+ Control
– Control
N/C
1
6
2
5
3
4
+ Load
– Load
Switching Characteristics
of Normally Closed Devices
Form-B
IF
ILOAD
10%
toff
DS-LCB110-R10
www.ixysic.com
90%
ton
1
INTEGRATED CIRCUITS DIVISION
LCB110
Absolute Maximum Ratings @ 25ºC
Parameter
Blocking Voltage
Reverse Input Voltage
Input Control Current
Peak (10ms)
Input Power Dissipation 1
Total Power Dissipation 2
Isolation voltage, Input to Output
Operational Temperature, Ambient
Storage Temperature
1
Ratings
350
5
50
1
150
800
3750
-40 to +85
-40 to +125
Absolute Maximum Ratings are stress ratings. Stresses in
excess of these ratings can cause permanent damage to
the device. Functional operation of the device at conditions
beyond those indicated in the operational sections of this
data sheet is not implied.
Units
VP
V
mA
A
mW
mW
Vrms
°C
°C
Derate linearly 1.33 mW / ºC
Derate output power linearly 6.67 mW / ºC
2
Electrical Characteristics @ 25ºC
Parameter
Output Characteristics
Blocking Voltage
Load Current
Continuous, AC/DC Configuration
Continuous, DC Configuration
Peak
On-Resistance 1
AC/DC Configuration
DC Configuration
Off-State Leakage Current
Switching Speeds
Turn-On
Turn-Off
Output Capacitance
Input Characteristics
Input Control Current to Activate
Input Control Current to Deactivate
Input Voltage Drop
Reverse Input Current
Common Characteristics
Input to Output Capacitance
1
Conditions
Symbol
Min
Typ
Max
Units
IL=1A
VDRM
350
-
-
VP
-
IL
-
-
t=10ms
IL
-
-
120
200
±350
mArms / mADC
mADC
mAP
23
7
-
35
10
1
ILEAK
-
IF=5mA, VL=50V, f=1MHz
ton
toff
COUT
-
0.38
0.93
25
3
3
-
IL=120mA
IF=5mA
VR=5V
IF
IF
VF
IR
0.4
0.9
-
0.7
1.2
-
5
1.4
10
mA
mA
V
A
-
CI/O
-
3
-
pF
IL=120mA
IL=200mA
IF=5mA, VL=350VP
RON
IF=5mA, VL=10V
A
ms
pF
Measurement taken within 1 second of on-time.
2
www.ixysic.com
R10
INTEGRATED CIRCUITS DIVISION
LCB110
PERFORMANCE DATA*
Typical LED Forward Voltage Drop
(N=50, IF=5mA)
25
Device Count (N)
25
20
15
10
20
15
10
5
5
20
15
10
5
0
0
1.17
0
0.18
1.19
1.21
1.23
1.25
LED Forward Voltage Drop (V)
0.25
0.32
0.39
0.46
Turn-On Time (ms)
0.53
0.75
Typical IF for Switch Dropout
(N=50, IL=120mADC)
Typical IF for Switch Operation
(N=50, IL=120mADC)
25
Device Count (N)
20
15
10
5
0.50
0.55 0.60 0.65 0.70
LED Current (mA)
0.80
0.85 0.90 0.95 1.0
Turn-Off Time (ms)
1.05
Typical On-Resistance Distribution
(N=50, IL=120mADC)
25
25
20
20
15
10
5
0
0
0.45
Typical Turn-Off Time
(N=50, IF=5mA, IL=120mADC)
25
Device Count (N)
Device Count (N)
30
Device Count (N)
35
Device Count (N)
Typical Turn-On Time
(N=50, IF=5mA, IL=120mADC)
15
10
5
0
0.40
0.75
0.45
0.50 0.55 0.60 0.65
LED Current (mA)
0.70
22.4
22.7
23.0 23.3 23.6 23.9
On-Resistance (:)
24.2
Typical Blocking Voltage Distribution
(N=50, IF=5mA)
Device Count (N)
25
20
15
10
5
0
370
0.25
1.4
I F =50mA
1.2
I F =10mA
I F =5mA
1.0
0.6
0.20
0.15
0.10
0.05
0.8
-20
0
20
40
60
80
Temperature (ºC)
100
120
0.5
0.4
0.3
0.2
0.1
0
0
-40
Typical Turn-Off Time
vs. LED Forward Current
(IL=120mADC)
0.7
Turn-Off Time (ms)
1.6
Turn-On Time (ms)
LED Forward Voltage Drop (V)
0.30
395
Typical Turn-On Time
vs. LED Forward Current
(IL=120mADC)
Typical LED Forward Voltage Drop
vs. Temperature
1.8
375
380
385
390
Blocking Voltage (VP)
0
5
10 15 20 25 30 35 40
LED Forward Current (mA)
45
50
0
5
10 15 20 25 30 35 40
LED Forward Current (mA)
45
50
*Unless otherwise noted, data presented in these graphs is typical of device operation at 25ºC.
R10
www.ixysic.com
3
INTEGRATED CIRCUITS DIVISION
LCB110
PERFORMANCE DATA*
0.6
50
0.5
40
30
AC/DC Configuration
20
10
Typical Turn-On Time
vs. Temperature
(IF=5mA, IL=120mADC)
1.8
0.4
0.3
0.2
0.1
-20
0
20
40
60
Temperature (ºC)
80
100
-40
Typical On-Resistance
vs. Temperature
(IL=100mA)
50
45
40
35
30
25
20
15
10
5
0
-20
0
20
40
60
Temperature (ºC)
80
1.2
1.0
0.8
I F =10mA
0.6
100
-40
Typical IF for Switch Operation
vs. Temperature
(IL=120mADC)
3.0
2.0
1.5
1.0
0.5
0
20
40
60
Temperature (ºC)
80
Maximum Load Current
vs. Temperature
(IF=0mA)
220
200
160
140
120
100
AC/DC Configuration
80
-20
0
20
40
60
Temperature (ºC)
80
40
-20
0
20
40
60
80
Temperature (ºC)
395
50
0
-50
100
120
-3
-2
0
-1
1
Load Voltage (V)
20
40
60
Temperature (ºC)
80
100
80
100
Typical Blocking Voltage
vs. Temperature
(IF=5mA)
390
385
380
375
370
Load Current (A)
0.030
0.025
0.020
0.015
0.010
0.005
20
40
60
Temperature (ºC)
80
2
3
4
-40
-20
0
20
40
60
Temperature (ºC)
Energy Rating Curve
0.035
0
0
365
-4
0.040
Leakage (PA)
-20
-40
100
0.045
-20
1.0
400
Typical Leakage vs. Temperature
Measured Across Pins 4&6
(IF=5mA, VL=350V)
0
-40
1.5
150
-150
-40
2.0
100
-100
60
100
Typical IF for Switch Dropout
vs. Temperature
(IL=120mADC)
Typical Load Current
vs. Load Voltage
DC Configuration
180
80
0
-40
100
Blocking Voltage (VP)
-20
20
40
60
Temperature (ºC)
0.5
0
-40
0
2.5
LED Current (mA)
LED Current (mA)
Instantaneous
-20
3.0
2.5
Load Current (mA)
On-Resistance (:)
1.4
0
-40
Load Current (mA)
I F =5mA
1.6
0.4
DC Configuration
0
Typical Turn-Off Time
vs. Temperature
(IL=120mADC)
2.0
Turn-Off Time (ms)
60
Turn-On Time (ms)
On-Resistance (:)
Typical On-Resistance
vs. Temperature
(IL=120mADC)
100
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
10Ps 100Ps 1ms 10ms 100ms
Time
1s
10s 100s
*Unless otherwise noted, data presented in these graphs is typical of device operation at 25ºC.
4
www.ixysic.com
R10
INTEGRATED CIRCUITS DIVISION
LCB110
Manufacturing Information
Moisture Sensitivity
All plastic encapsulated semiconductor packages are susceptible to moisture ingression. IXYS Integrated
Circuits classifies its plastic encapsulated devices for moisture sensitivity according to the latest version of
the joint industry standard, IPC/JEDEC J-STD-020, in force at the time of product evaluation. We test all of
our products to the maximum conditions set forth in the standard, and guarantee proper operation of our devices
when handled according to the limitations and information in that standard as well as to any limitations set forth in the
information or standards referenced below.
Failure to adhere to the warnings or limitations as established by the listed specifications could result in reduced product
performance, reduction of operable life, and/or reduction of overall reliability.
This product carries a Moisture Sensitivity Level (MSL) classification as shown below, and should be handled
according to the requirements of the latest version of the joint industry standard IPC/JEDEC J-STD-033.
Device
Moisture Sensitivity Level (MSL) Classification
LCB110S
MSL 1
ESD Sensitivity
This product is ESD Sensitive, and should be handled according to the industry standard JESD-625.
Soldering Profile
Provided in the table below is the IPC/JEDEC J-STD-020 Classification Temperature (TC) and the maximum total dwell
time (tP) in all reflow processes that the body temperature of these surface mount devices may be (TC - 5)°C or greater.
The device’s body temperature must not exceed the Classification Temperature at any time during reflow soldering
processes.
Device
Classification Temperature (Tc)
Dwell Time (tP)
Max Reflow Cycles
LCB110S
250ºC
30 seconds
3
For through-hole devices, the maximum pin temperature and maximum dwell time through all solder waves is
provided in the table below. Dwell time is the interval beginning when the pins are initially immersed into the solder
wave until they exit the solder wave. For multiple waves, the dwell time is from entering the first wave until exiting the
last wave. During this time, pin temperatures must not exceed the maximum temperature given in the table below.
Body temperature of the device must not exceed the limit shown in the table below at any time during the soldering
process.
Device
LCB110
Maximum Pin Temperature
260ºC
Maximum Body Temperature
250ºC
Maximum Dwell Time
10 seconds*
Wave Cycles
1
*Total cumulative duration of all waves.
Board Wash
IXYS Integrated Circuits recommends the use of no-clean flux formulations. Board washing to reduce or remove flux
residue following the solder reflow process is acceptable provided proper precautions are taken to prevent damage to
the device. These precautions include but are not limited to: using a low pressure wash and providing a follow up bake
cycle sufficient to remove any moisture trapped within the device due to the washing process. Due to the variability
of the wash parameters used to clean the board, determination of the bake temperature and duration necessary
to remove the moisture trapped within the package is the responsibility of the user (assembler). Cleaning or drying
methods that employ ultrasonic energy may damage the device and should not be used. Additionally, the device must
not be exposed to halide flux or solvents.
R10
www.ixysic.com
5
INTEGRATED CIRCUITS DIVISION
LCB110
MECHANICAL DIMENSIONS
LCB110
8.382±0.381
(0.330±0.015)
PCB Hole Pattern
7.239 TYP
(0.285 TYP)
2.54±0.127
(0.100±0.005)
6 - 0.800 DIA.
(6 - 0.031 DIA.)
9.144±0.508
(0.360±0.020)
6.350±0.127
(0.250±0.005)
1.524 TYP
(0.060 TYP)
Pin 1
1.651±0.254
(0.065±0.010)
2.540±0.127
(0.100±0.005)
7.620±0.127
(0.300±0.005)
7.620±0.254
(0.300±0.010)
0.254±0.0127
(0.010±0.0005)
5.080±0.127
(0.200±0.005)
Controlling dimension: inches
3.302±0.051
(0.130±0.002)
4.064 TYP
(0.160 TYP)
Dimensions
mm
(inches)
0.457±0.076
(0.018±0.003)
LCB110S
8.382±0.381
(0.330±0.015)
9.524±0.508
(0.375±0.020)
Pin 1
0.635±0.127
(0.025±0.005)
2.54
(0.10)
6.350±0.127
(0.250±0.005)
0.457±0.076
(0.018±0.003)
1.651±0.254
(0.065±0.010)
7.620±0.254
(0.300±0.010)
0.254±0.0127
(0.010±0.0005)
8.90
(0.3503)
1.65
(0.0649)
0.65
(0.0255)
3.302±0.051
(0.130±0.002)
4.445±0.254
(0.175±0.010)
Controlling dimension: inches
1.524 TYP
(0.060 TYP)
1.651±0.254
(0.065±0.010)
6
PCB Land Pattern
2.54±0.127
(0.100±0.005)
Dimensions
mm
(inches)
www.ixysic.com
R10
INTEGRATED CIRCUITS DIVISION
LCB110
LCB110STR Tape & Reel
P1 = 12.00
(0.472)
330.2 Dia
(13.00 Dia)
Top Cover
Tape Thickness
0.102 Max
(0.004 Max)
W=16.00
(0.63)
B0 = 10.10
(0.398)
K0 = 4.90
(0.19)
K1 = 3.80
(0.15)
A0 = 10.10
(0.398)
User Direction of Feed
Embossed
Carrier
Embossment
Dimensions
mm
(inches)
NOTES:
1. All dimensions carry tolerances of EIA Standard 481-2
2. The tape complies with all “Notes” for constant dimensions listed on page 5 of EIA-481-2
For additional information please visit our website at: https://www.ixysic.com
Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and
test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications.
Read complete Disclaimer Notice at https://www.littelfuse.com/disclaimer-electronics.
7
Specification: DS-LCB110-R10
©Copyright 2021, Littelfuse, Inc.
OptoMOS® is a registered trademark of IXYS Integrated Circuits Division
All rights reserved. Printed in USA.
11/2/2021
