CPC1563GSTR

CPC1563 Single-Pole, Normally Open, Current Limited OptoMOS® Relay with Voltage Triggered Shutdown and Thermal Management INTEGRATED CIRCUITS DIVISION Parameter Load Voltage Load Current On-Resistance (max) Input Control Current Rating 600 ±120 35 2 Description Units VP mA  mA Features • Integrated Active Current-Limit with Voltage Triggered Shutdown • Thermal Shutdown • Guaranteed Turn-On: 2mA Input Control Current • 600VP Blocking Voltage • 3750Vrms Input/Output Isolation • Small Surface Mount Package • Low Drive Power Requirements • Arc-Free With No Snubbing Circuits • No EMI/RFI Generation • Flammability Rating UL 94 V-0 Applications • • • • • • • • • • • Simplifies Telecom Secondary Protection Telephony Hook Switch VoIP Gateways IP-PBXs Satellite and Cable Set-top Boxes V.92 (and Other Standard) Modems Embedded Modems for POS Terminals, Automated Banking, Remote Metering, Vending Machines, Security, and Surveillance Instrumentation Medical Equipment—Patient/Equipment Isolation Aerospace Industrial Controls Block Diagram Gate Drive Control VF - Approvals • UL Recognized Component: File E76270 • CSA Certified Component: Certificate 1172007 • EN/IEC 60950-1 Certified Component: Certificate available on our website Ordering Information LOAD + The CPC1563 is a normally open (1-Form-A) Solid State Relay with an integrated current limit feature that targets the international hook switch telephony market by providing excellent power-cross immunity for improved survivability in harsh environments. When a fault condition occurs, usually in the form of a voltage rise across the load/relay combination, the relay will limit the current flow through the load to ILMT. As the fault voltage increases, the load is protected by the relay's current limit, but the relay itself must dissipate more and more power. If, while the relay is in current limit, the voltage dropped across the relay rises to the Voltage Triggered Shutdown threshold, VTH, then the current through the relay, and the load, is cut to a nominal 100A. In the event of a fault condition that persists, and with or without VTH being exceeded, the temperature of the relay's die could rise to a level that might damage it. In this instance, internal thermal management circuitry shuts the relay down. When the voltage across the relay drops below VTH, and if the device is not in thermal shutdown, normal operation is restored. If the fault condition persists, then the events described above repeat. When provided with adequate overvoltage protection, the CPC1563 can pass regulatory voltage surge requirements. The CPC1563 relay may be used in both AC and DC applications. Part # CPC1563G CPC1563GS CPC1563GSTR Current Limit and Over-Voltage Protection Description 6-Pin DIP (50/Tube) 6-Pin Surface Mount (50/Tube) 6-Pin Surface Mount, Tape & Reel (1000/Reel) Switching Characteristics of Normally Open Devices Thermal Management Form-A IF LOAD 90% 10% ILOAD ton DS-CPC1563-R02 www.ixysic.com toff 1 INTEGRATED CIRCUITS DIVISION CPC1563 Absolute Maximum Ratings @ 25ºC Parameter Blocking Voltage Reverse Input Voltage Input Control Current Peak (10ms) Input Power Dissipation 1 Total Power Dissipation 2 Isolation Voltage, Input to Output (60 Seconds) Operational Temperature (TA) Storage Temperature 1 2 Ratings Units 600 VP 5 V 50 mA 1 A 150 mW 800 mW 3750 Vrms -40 to +85 °C -40 to +125 °C Absolute Maximum Ratings are stress ratings. Stresses in excess of these ratings can cause permanent damage to the device. Functional operation of the device at conditions beyond those indicated in the operational sections of this data sheet is not implied. Typical values are characteristic of the device at +25°C, and are the result of engineering evaluations. They are provided for information purposes only, and are not part of the manufacturing testing requirements. Derate linearly 3.33 mW / ºC Derate linearly 6.67 mW / ºC Recommended Operating Conditions Parameter Load Current, Continuous Symbol Configuration AC/DC DC-Only - IL Input Control Current Operating Temperature IF TA Min 3 -40 Typ 5 - Max 120 250 10 +85 Units mArms / mADC mADC mA ºC Electrical Characteristics @ 25ºC Parameter Output Characteristics Current Limit AC/DC Configuration DC Configuration Voltage Triggered Shutdown Threshold On-Resistance AC/DC Configuration DC Configuration Off-State Leakage Current Switching Speeds Turn-On Turn-Off Output Capacitance Conditions IF=5mA, VL=13V, t=5ms IF=5mA, VL=6.5V, t=5ms IF=5mA IF=5mA, IL=120mA IF=5mA, IL=220mA VL=600V ILMT VTH RON ILEAK + – Do Not Use 2 Typ Max Units ±190 360 100 ±225 430 - ±285 570 - 15 3.75 - 23 7.1 - 35 11.75 1 A mA V  ton toff - 1.22 0.3 2 ms IF=0mA, VL=20V CO - 18 - pF IL=100mA IL