CPC1961G

CPC1961 Dual AC Solid State Relays INTEGRATED CIRCUITS DIVISION Parameters Blocking Voltage AC Operating Voltage Load Current 1 On State Voltage Drop 1 Ratings 600 260 250 3 One Pole Operating Features • • • • • • • • • Load Current up to 250 mArms 600VP Blocking Voltage 5mA Sensitivity Zero-Crossing Detection DC Control, AC Output Optically Isolated Low EMI and RFI Generation High Noise Immunity Flammability Rating UL 94 V-0 Units VP Vrms mArms Vrms (at IL = 250mArms) Description The CPC1961 is a dual single-pole AC solid state relay that uses optical coupling with dual monolithic SCR outputs to produce an alternative to optocoupler and Triac circuits. The CPC1961 switches are robust enough to provide up to a 600VP blocking voltage. In addition, tightly controlled zero cross circuitry ensures switching of AC loads without the generation of transients. The input and output circuits are optically coupled to provide 3750Vrms of isolation and noise immunity between control and load circuits. As a result the CPC1961 is well suited for industrial environments where electromagnetic interference would disrupt the operation of electromechanical relays. The CPC1961 is offered in a space saving 8-pin DIP package with two independent switches. Applications • • • • • • • • • • Programmable Control Process Control Power Control Panels Remote Switching Gas Pump Electronics Contactors Large Relays Solenoids Motors Heaters Approvals • UL Recognized Component: File 69938 • CSA Certified Component: File 043639 Ordering Information Part # CPC1961G CPC1961GS CPC1961GSTR Description 8-Pin Dip (50/Tube) 8-Pin Surface Mount (50/Tube) 8-Pin Surface Mount (1000/Reel) Pin Configuration 8 AC Load + LED 1 ZC 7 AC Load – LED 2 6 AC Load + LED 3 ZC – LED 4 DS-CPC1961-R09 www.ixysic.com 5 AC Load 1 INTEGRATED CIRCUITS DIVISION CPC1961 Absolute Maximum Ratings @ 25ºC Parameter Blocking Voltage Reverse Input Voltage Input Control Current Peak (10ms) Input Power Dissipation 1 Total Package Dissipation 2 Isolation Voltage, Input to Output Operational Temperature Storage Temperature 1 Ratings Units 600 VP 5 VP 50 mA 1 A 150 mW 800 mW 3750 Vrms -40 to +85 °C -40 to +125 °C Absolute Maximum Ratings are stress ratings. Stresses in excess of these ratings can cause permanent damage to the device. Functional operation of the device at conditions beyond those indicated in the operational sections of this data sheet is not implied. Typical values are characteristic of the device at +25°C, and are the result of engineering evaluations. They are provided for information purposes only, and are not part of the manufacturing testing requirements. Derate linearly 1.33 mW / ºC Derate linearly 6.67 mW / ºC 2 Electrical Characteristics @ 25ºC Parameters Output Characteristics Operating Voltage Range Load Current 1, Continuous Non-repetitive Single Cycle Surge Current Off State Leakage Current On-State Voltage Drop Critical Rate of Rise 2 Holding Current Switching Speeds Turn-on Turn-off Zero-Cross Turn-On Voltage 3 Operating Frequency Load Power Factor for Guaranteed Turn-On 4 Input Characteristics Input Control Current to Activate 5 Input Voltage Drop Input Drop-out Voltage Reverse Input Current Common Characteristics Input to Output Capacitance Conditions Symbol Min Typ Max Units VL - 20 - 260 Vrms VL=120-240Vrms t < 10ms VL=600V IL=250 mArms IF=5 mA IL 0.005 500 - 300 250 1 1 3 - mArms A µA Vrms V/µs µA 20 0.25 5 - 0.5 0.5 20 5 500 - 1.2 1.2 - 5 1.5 10 mA V V µA 3 - pF IF=5 mA 1st half-cycle Subsequent half-cycles - ITSM ILEAK dV/dt IH ton toff PF IF=5mA VR=5V IF VF IR 0.9 0.8 - VIO=0V, f=1MHz CIO - cycles V V Hz - 1 Maximum continuous load current of a single pole or the sum of the load currents with both poles operating simultaneously. 2 Tested in accordance with EIA/NARM standard RS-443. 3 Zero Cross 1st half-cycle @