LBA120LS

LBA120L 250V, 150mA Dual Single-Pole Relays: 1-Form-A (NO) & 1-Form-B (NC) INTEGRATED CIRCUITS DIVISION Parameter Blocking Voltage Load Current On-Resistance (max) Ratings 250 150 25 Units VP mArms / mADC  Features • • • • • • • • • • Current Limited 3750Vrms Input/Output Isolation Low Drive Power Requirements Greater Reliability than Electromechanical Relays FCC Compatible VDE Compatible No EMI/RFI Generation Small 8-Pin Package Surface Mount, Tape & Reel Version Available Flammability Rating UL 94 V-0 Applications • Telecommunications • Telecom Switching • Tip/Ring Circuits • Modem Switching (Laptop, Notebook, Pocket Size) • Hook Switch • Dial Pulsing • Ground Start • Ringing Injection • Instrumentation • Multiplexers • Data Acquisition • Electronic Switching • I/O Subsystems • Meters (Watt-Hour, Water, Gas) • Medical Equipment-Patient/Equipment Isolation • Security • Industrial Controls Description The LBA120L comprises two independent, single-pole, 250V, 150mA, 20 solid state relays: one single-pole, normally open (1-Form-A) current limiting relay and one single-pole, normally closed (1-Form-B) relay. The LBA120L is designed to provide an ideal solution where a complementary Form-A/Form-B relay pair is required. Approvals • UL Recognized Component: File # E76270 • CSA Certified Component: Certificate # 1175739 • TUV EN 62368-1: Certificate # B 082667 0008 Ordering Information Part # LBA120L LBA120LS LBA120LSTR Description 8-Pin DIP (50/Tube) 8-Pin Surface Mount (50/Tube) 8-Pin Surface Mount (1,000/Reel) Pin Configuration + Control - Normally Closed – Control - Normally Closed + Control - Normally Open – Control - Normally Open 1 8 2 7 3 6 4 5 Switching Characteristics of Normally Open Devices Normally Open Pole Switching Characteristics of Normally Closed Devices Form-A Form-B IF IF ILOAD 90% 10% ILOAD ton DS-LBA120L-R07 Normally Closed Pole www.ixysic.com toff 10% toff 90% ton 1 INTEGRATED CIRCUITS DIVISION LBA120L Absolute Maximum Ratings TA=25ºC Parameter Blocking Voltage Reverse Input Voltage Input Control Current Peak (10ms) Input Power Dissipation 1 Total Power Dissipation 2 Isolation Voltage, Input to Output Operational Temperature, Ambient Storage Temperature 1 2 Symbol Ratings Units VB 250 VP VR 5 V 50 mA IF 1 A PI 150 mW PD 800 mW VISO 3750 Vrms TA -40 to +85 °C TSTG -40 to +125 °C Absolute Maximum Ratings are stress ratings. Stresses in excess of these ratings can cause permanent damage to the device. Functional operation of the device at conditions beyond those indicated in the operational sections of this data sheet is not implied. Typical values are characteristic of the device at +25°C, and are the result of engineering evaluations. They are provided for information purposes only, and are not part of the manufacturing testing requirements. Derate linearly 1.33 mW / ºC Derate output power linearly 6.67 mW / ºC Electrical Characteristics TA=25ºC Parameter Output Characteristics Blocking Voltage Load Current Continuous 1 Load Current Limiting (1-Form-A Only) On-Resistance Off-State Leakage Current Switching Speeds Turn-On Turn-Off Output Capacitance Input Characteristics Input Control Current to Activate Input Control Current to Deactivate Input Voltage Drop Reverse Input Current Common Characteristics Input to Output Capacitance 1 2 Conditions Symbol Min Typ Max Units IL=1A VDRM 250 - - VP IL=170mA VL=250VP IL ICL RON ILEAK ±190 - ±235 21 - 150 ±280 25 1 mArms / mADC mA  VL=50V, f=1MHz ton toff COUT - 50 5 5 - IL=120mA IF=5mA VR=5V IF IF VF IR 0.4 0.9 - 0.7 1.36 - 5 1.5 10 mA mA V A VIO=0V, f=1MHz CIO - 3 - pF IF=5mA, VL=10V A ms pF If both poles operate, then the load current must be derated so as not to exceed the package's power dissipation rating. www.ixysic.com R07 INTEGRATED CIRCUITS DIVISION LBA120L Form-A/Form-B PERFORMANCE DATA* Typical LED Forward Voltage Drop vs. Temperature LED Forward Voltage Drop (V) 30 Typical LED Forward Voltage Drop (N=50, IF=5mA) Device Count (N) 25 20 15 10 5 0 1.364 1.8 1.7 1.6 IF=10mA IF=5mA IF=2mA 1.5 1.4 1.3 1.2 1.1 1.0 -50 1.366 1.368 1.370 1.372 LED Forward Voltage Drop (V) -25 0 25 50 Temperature (ºC) 75 100 Form-A RELAY PERFORMANCE DATA* Form-A Typical Turn-On Time (N=50, IF=5mA, IL=170mADC) 30 35 20 15 10 25 20 15 10 5 5 0 0 0.23 0.32 0.41 0.50 0.59 0.68 0.77 25 20 15 10 5 0 0.06 0.10 0.14 0.18 0.22 0.26 0.30 14.0 14.4 14.8 15.2 15.6 Turn-On Time (ms) Turn-Off Time (ms) On-Resistance (:) Form-A Typical IF for Switch Operation (N=50, IL=170mADC) Form-A Typical IF for Switch Dropout (N=50, IL=170mADC) Form-A Typical Blocking Voltage Distribution (N=50) 25 35 35 25 20 15 10 30 20 Device Count (N) 30 Device Count (N) Device Count (N) Form-A Typical On-Resistance Distribution (N=50, IF=5mA, IL=170mADC) 30 Device Count (N) Device Count (N) Device Count (N) 35 30 25 40 Form-A Typical Turn-Off Time (N=50, IF=5mA, IL=170mADC) 15 10 5 0 0.6 0.8 1.0 1.2 1.4 LED Current (mA) 1.6 1.8 20 15 10 5 5 0 25 0 0.3 0.5 0.7 0.9 1.1 LED Current (mA) 1.3 1.5 380 384 388 392 396 400 Blocking Voltage (VP) *Unless otherwise noted, data presented in these graphs is typical of device operation at 25ºC. R07 www.ixysic.com 3 INTEGRATED CIRCUITS DIVISION LBA120L Form-A PERFORMANCE DATA* Form-A Typical Turn-On Time vs. LED Forward Current (IL=170mADC) 0.16 0.30 0.25 0.20 0.13 0.12 4 6 8 10 12 14 16 LED Forward Current (mA) 18 Form-A Typical IF for Switch Dropout vs. Temperature (IL=170mADC) 3.0 Turn-On Time (ms) 2.0 1.5 1.0 0.5 -20 0 20 40 60 80 6 8 10 12 14 16 18 20 -40 -20 0 20 40 60 Temperature (ºC) Form-A Typical Turn-On Time vs. Temperature (IL=170mADC) Form-A Typical Turn-Off Time vs. Temperature (IF=5mA, IL=170mADC) 0.30 IF=5mA 0.5 0.4 IF=10mA 0.3 IF=20mA 0.2 80 100 80 100 0.25 0.20 0.15 0.10 0.05 0 -40 100 1.0 LED Forward Current (mA) 0 -40 -20 0 20 40 60 80 -40 100 -20 0 20 40 60 Temperature (ºC) Temperature (ºC) Temperature (ºC) Form-A Typical On-Resistance vs. Temperature (IF=5mA, IL=170mADC) Form-A Typical Load Current vs. Load Voltage (IF=5mA) Form-A Maximum Load Current vs. Temperature 200 250 50 40 30 20 10 Load Current (mA) 150 Load Current (mA) 100 50 0 -50 -100 200 150 IF=20mA IF=10mA IF=5mA 100 50 -150 0 -40 -20 0 20 40 60 80 -200 -2.5 -2.0 -1.5 -1.0 -0.5 100 0 0 -40 0.5 1.0 1.5 2.0 2.5 -20 0 20 40 60 80 100 120 Temperature (ºC) Load Voltage (V) Temperature (ºC) Form-A Typical Blocking Voltage vs. Temperature Form-A Typical Leakage vs. Temperature (Measured across Pins 5&6) Typical Current Limiting vs. Temperature (IF=5mA) 0.18 395 0.16 Leakage (PA) 400 390 385 400 350 300 Current (mA) On-Resistance (:) 4 0.1 0 Blocking Voltage (VP) 2 0.6 2.5 LED Current (mA) 0 20 Turn-Off Time (ms) 2 1.5 0 0.10 0 2.0 0.5 0.11 0.10 60 2.5 0.14 0.15 Form-A Typical IF for Switch Operation vs. Temperature (IL=170mADC) 3.0 0.15 LED Current (mA) 0.35 Turn-Off Time (ms) Turn-On Time (ms) 0.40 Form-A Typical Turn-Off Time vs. LED Forward Current (IL=170mADC) 0.14 0.12 0.10 250 200 150 100 380 0.08 375 50 0 0.06 -40 -20 0 20 40 60 Temperature (ºC) 80 100 -40 -20 0 20 40 60 Temperature (ºC) 80 100 -40 -20 0 20 40 60 80 100 Temperature (ºC) *Unless otherwise noted, data presented in these graphs is typical of device operation at 25ºC. 4 www.ixysic.com R07 INTEGRATED CIRCUITS DIVISION LBA120L Form-B PERFORMANCE DATA* Form-B Typical Turn-On Time (N=50, IF=5mA, IL=170mADC) 35 35 20 15 10 25 20 15 10 5 5 0 0 0.42 0.54 0.66 0.78 35 1.375 1.625 15 10 10.4 0 0.81 0.99 1.17 1.35 35 0.63 0.626 0.81 0.99 1.17 Blocking Voltage (VP) Form-B Typical Turn-Off Time vs. LED Forward Current (IL=170mADC) Form-B Typical IF for Switch Operation vs. Temperature (IL=170mADC) 3.0 2.5 1.0 0.8 0.6 0.4 3.0 5 10 15 20 25 30 35 40 45 1.0 5 10 15 20 25 30 35 40 45 -40 50 -20 0 20 40 60 LED Forward Current (mA) LED Forward Current (mA) Temperature (ºC) Form-B Typical IF for Switch Dropout vs. Temperature (IL=170mADC) Form-B Typical Turn-On Time vs. Temperature (IF=5mA, IL=170mADC) Form-B Typical Turn-Off Time vs. Temperature (IL=170mADC) 0.12 Turn-On Time (ms) 2.5 2.0 1.5 1.0 0.5 2.5 0.10 0.08 0.06 0.04 0.02 -20 0 20 40 Temperature (ºC) 60 80 100 80 100 IF=5mA 2.0 1.5 IF=10mA 1.0 IF=20mA 0.5 0 0 0 -40 1.5 0 0 50 2.0 0.5 Turn-Off Time (ms) 0 10 291.25 293.75 296.25 298.75 301.25 303.75 0 0.622 15 LED Current (mA) 0.2 0.624 20 1.35 LED Current (mA) Turn-Off Time (ms) 0.628 25 0 1.2 0.630 12.4 5 0.45 0.632 12.0 Form-B Typical Blocking Voltage Distribution (N=50, IF=5mA) LED Current (mA) 0.634 11.6 30 1.53 Form-B Typical Turn-On Time vs. LED Forward Current (IL=170mADC) 11.2 Form-B Typical IF for Switch Dropout (N=50, IL=170mADC) 10 0 10.8 On-Resistance (:) 15 5 10 Turn-Off Time (ms) 20 5 15 1.875 Device Count (N) 20 0.63 Turn-On Time (ms) 1.125 25 Device Count (N) Device Count (N) 25 20 0 0.625 0.875 Turn-On Time (ms) 30 25 5 0.90 Form-B Typical IF for Switch Operation (N=50, IL=170mADC) Form-B Typical On-Resistance Distribution (N=50, IL=170mADC) 30 Device Count (N) Device Count (N) 25 0.30 LED Current (mA) 35 30 30 Device Count (N) Form-B Typical Turn-Off Time (N=50, IF=5mA, IL=170mADC) -40 -20 0 20 40 60 Temperature (ºC) 80 100 -40 -20 0 20 40 60 80 100 Temperature (ºC) *Unless otherwise noted, data presented in these graphs is typical of device operation at 25ºC. R07 www.ixysic.com 5 INTEGRATED CIRCUITS DIVISION LBA120L Form-B PERFORMANCE DATA* Form-B Typical On-Resistance vs. Temperature (IF=0mA, IL=170mADC) 200 30 20 Load Current (mA) 40 10 100 50 0 -50 -100 200 150 100 50 -150 0 -40 310 -20 0 20 40 60 80 -200 -2.0 100 0 -1.5 -1.0 -0.5 0 0.5 1.0 1.5 Temperature (ºC) Load Voltage (V) Form-B Typical Blocking Voltage vs. Temperature (IF=5mA) Form-B Typical Leakage vs. Temperature Measured across Pins 7&8 (IF=5mA) 0.030 -40 2.0 295 290 -40 -20 0 20 40 60 Temperature (ºC) 80 100 40 60 80 100 120 1.0 0.020 0.015 0.010 0 -40 20 Energy Rating Curve 0.8 0.6 0.4 0.2 0.005 285 0 1.2 Load Current (A) 300 -20 Temperature (ºC) 0.025 305 Leakage (PA) Blocking Voltage (VP) 250 150 50 Load Current (mA) On-Resistance (:) 60 Form-B Maximum Load Current vs. Temperature (IF=0mA) Form-B Typical Load Current vs. Load Voltage (IF=0mA) -20 0 20 40 60 80 100 0 10Ps 100Ps 1ms 10ms 100ms Temperature (ºC) 1s 10s 100s Time *Unless otherwise noted, data presented in these graphs is typical of device operation at 25ºC. 6 www.ixysic.com R07 INTEGRATED CIRCUITS DIVISION LBA120L Manufacturing Information Moisture Sensitivity All plastic encapsulated semiconductor packages are susceptible to moisture ingression. IXYS Integrated Circuits classifies its plastic encapsulated devices for moisture sensitivity according to the latest version of the joint industry standard, IPC/JEDEC J-STD-020, in force at the time of product evaluation. We test all of our products to the maximum conditions set forth in the standard, and guarantee proper operation of our devices when handled according to the limitations and information in that standard as well as to any limitations set forth in the information or standards referenced below. Failure to adhere to the warnings or limitations as established by the listed specifications could result in reduced product performance, reduction of operable life, and/or reduction of overall reliability. This product carries a Moisture Sensitivity Level (MSL) classification as shown below, and should be handled according to the requirements of the latest version of the joint industry standard IPC/JEDEC J-STD-033. Device Moisture Sensitivity Level (MSL) Classification LBA120LS MSL 1 ESD Sensitivity This product is ESD Sensitive, and should be handled according to the industry standard JESD-625. Soldering Profile Provided in the table below is the IPC/JEDEC J-STD-020 Classification Temperature (TC) and the maximum dwell time the body temperature of these surface mount devices may be (TC - 5)°C or greater. The Classification Temperature sets the Maximum Body Temperature allowed for these devices during reflow soldering processes. Device Classification Temperature (Tc) Dwell Time (tP) Max Reflow Cycles LBA120LS 250ºC 30 seconds 3 For through-hole devices, the maximum pin temperature and maximum dwell time through all solder waves is provided in the table below. Dwell time is the interval beginning when the pins are initially immersed into the solder wave until they exit the solder wave. For multiple waves, the dwell time is from entering the first wave until exiting the last wave. During this time, pin temperatures must not exceed the maximum temperature given in the table below. Body temperature of the device must not exceed the limit shown in the table below at any time during the soldering process. Device LBA120L Maximum Pin Temperature 260ºC Maximum Body Temperature 250ºC Maximum Dwell Time 10 seconds* Wave Cycles 1 *Total cumulative duration of all waves. Board Wash IXYS Integrated Circuits recommends the use of no-clean flux formulations. Board washing to reduce or remove flux residue following the solder reflow process is acceptable provided proper precautions are taken to prevent damage to the device. These precautions include but are not limited to: using a low pressure wash and providing a follow up bake cycle sufficient to remove any moisture trapped within the device due to the washing process. Due to the variability of the wash parameters used to clean the board, determination of the bake temperature and duration necessary to remove the moisture trapped within the package is the responsibility of the user (assembler). Cleaning or drying methods that employ ultrasonic energy may damage the device and should not be used. Additionally, the device must not be exposed to halide flux or solvents. R07 www.ixysic.com 7 INTEGRATED CIRCUITS DIVISION LBA120L MECHANICAL DIMENSIONS LBA120L 2.540 ± 0.127 (0.100 ± 0.005) 9.652 ± 0.381 (0.380 ± 0.015) 8-0.762 DIA. (8-0.030 DIA.) 2.540 ± 0.127 (0.100 ± 0.005) 9.144 ± 0.508 (0.360 ± 0.020) 6.350 ± 0.127 (0.250 ± 0.005) Pin 1 PCB Hole Pattern 7.620 ± 0.254 (0.300 ± 0.010) 0.457 ± 0.076 (0.018 ± 0.003) 3.302 ± 0.051 (0.130 ± 0.002) 7.620 ± 0.127 (0.300 ± 0.005) 7.239 TYP. (0.285) 4.064 TYP (0.160) 0.254 ± 0.0127 (0.010 ± 0.0005) 7.620 ± 0.127 (0.300 ± 0.005) Dimensions mm (inches) 0.813 ± 0.102 (0.032 ± 0.004) LBA120LS PCB Land Pattern 9.652 ± 0.381 (0.380 ± 0.015) 2.540 ± 0.127 (0.100 ± 0.005) 6.350 ± 0.127 (0.250 ± 0.005) Pin 1 3.302 ± 0.051 (0.130 ± 0.002) 0.635 ± 0.127 (0.025 ± 0.005) 9.525 ± 0.254 (0.375 ± 0.010) 0.457 ± 0.076 (0.018 ± 0.003) 2.54 (0.10) 8.90 (0.3503) 1.65 (0.0649) 7.620 ± 0.254 (0.300 ± 0.010) 0.254 ± 0.0127 (0.010 ± 0.0005) 0.65 (0.0255) 4.445 ± 0.127 (0.175 ± 0.005) Dimensions mm (inches) 0.813 ± 0.102 (0.032 ± 0.004) 8 www.ixysic.com R07 INTEGRATED CIRCUITS DIVISION LBA120L LBA120LSTR Tape & Reel 2.0 (0.08) 4.0 (0.16) 330.2 DIA. (13.00 DIA.) Top Cover Tape Thickness 0.102 MAX. (0.004 MAX.) 7.5 (0.30) Bo=10.30 (0.406) K0 =4.90 (0.193) K1 =4.20 (0.165) Embossed Carrier Embossment 16.0±0.3 (0.63±0.012) Ao=10.30 (0.406) P1=12.00 (0.472) User Direction of Feed Dimensions mm (inches) NOTES: 1. Dimensions carry tolerances of EIA Standard 481-2 2. Tape complies with all “Notes” for constant dimensions listed on page 5 of EIA-481-2 3. Controlling dimension: mm For additional information please visit our website at: https://www.ixysic.com Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at https://www.littelfuse.com/disclaimer-electronics. 9 Specification: DS-LBA120L-R07 ©Copyright 2021, Littelfuse, Inc. OptoMOS® is a registered trademark of IXYS Integrated Circuits All rights reserved. Printed in USA. 10/25/2021