MDD310-18N1

MDD 310 High Power Diode Modules VRSM V 1300 1500 1700 1900 2100 2300 VRRM V 1200 1400 1600 1800 2000 2200 IFRSM = 2x 480 A IFAVM = 2x 305 A VRRM = 1200-2200 V 3 Type 1 2 MDD 310-12N1 MDD 310-14N1 MDD 310-16N1 MDD 310-18N1 MDD 310-20N1 MDD 310-22N1 E72873 Conditions IFRMS IFAVM TVJ = TVJM TC = 100°C; 180° sine 480 305 A A IFSM TVJ = 45°C; VR = 0 t = 10 ms (50 Hz) t = 8.3 ms (60 Hz) 11,5 12,2 kA kA • Direct copper bonded Al2O3 ceramic base plate • Planar passivated chips • Isolation voltage 3600 V~ • UL registered, E 72873 TVJ = TVJM; VR = 0 t = 10 ms (50 Hz) t = 8.3 ms (60 Hz) 9,6 10,2 kA kA Applications TVJ = 45°C; VR = 0 t = 10 ms (50 Hz) t = 8.3 ms (60 Hz) 662 620 kA s kA2s TVJ = TVJM; VR = 0 t = 10 ms (50 Hz) t = 8.3 ms (60 Hz) 460 430 kA2s kA2s -40...+150 150 -40...+125 °C °C °C 3000 3600 V~ V~ 2.5 - 5 12 - 15 Nm Nm 320 g It 2 Maximum Ratings Features Symbol TVJ TVJM Tstg 2 VISOL 50/60 Hz, RMS t = 1 min IISOL < 1 mA t=1s Md Mounting torque (M5) Terminal connection torque (M8) Weight Typical including screws Symbol Conditions IRRM VR = VRRM; TVJ = TVJM 40 mA VF IF = 600 A; TVJ = 25°C 1.2 V VT0 rt For power-loss calculations only TVJ = TVJM 0.75 0.63 V mW RthJC per diode; DC current per module per diode; DC current per module 0.129 0.065 0.169 0.0845 K/W K/W K/W K/W RthJK • Supplies for DC power equipment • DC supply for PWM inverter • Field supply for DC motors • Battery DC power supplies Advantages • Space and weight savings • Simple mounting • Improved temperature and power cycling • Reduced protection circuits Characteristics Values other values see Fig. 6/7 QS IRM TVJ = 125°C; IF = 400 A; -di/dt = 50 A/µs 760 275 µC A dS dA a Creeping distance on surface Creepage distance in air Maximum allowable acceleration 12.7 9.6 50 mm mm m/s2 Data according to IEC 60747 and refer to a single diode unless otherwise stated. IXYS reserves the right to change limits, test conditions and dimensions. © 2015 IXYS All rights reserved 20150910a 1-4 MDD 310 Dimensions in mm (1 mm = 0.0394“) 42.5 28.5 0.25 32 hex SW13 4.5 M8x16 35 65 x 57 116 6 5.5 38 60 80 4567 max. 12.4 Threaded spacer for higher Anode / Cathode construction: Type ZY 250 (material brass) IXYS reserves the right to change limits, test conditions and dimensions. © 2015 IXYS All rights reserved 20150910a 2-4 MDD 310 14000 106 12000 50 Hz 80 % VRRM TVJ = 45°C TVJ = 150°C 10000 IFS M [A ] VR = 0 V DC 180° sin 120° 60° 30° 500 400 I t 8000 IFA V M TVJ = 45°C 2 [A ] 2 [A s ] 6000 TVJ = 150°C 300 200 4000 100 2000 0 0.001 0.01 0.1 105 1 1 10 2 Fig. 1 Surge overload current IFSM: Crest value, t: duration 0 25 50 75 100 125 150 T C [°C ] t [m s ] t [s ] 0 Fig. 2 I t versus time (1-10 ms) Fig. 3 Maximum forward current at case temperature 500 R thKA K/W 0.3 0.4 0.5 0.6 0.8 1.0 1.4 1.8 400 P to t [W ] 300 DC 180 ° sin 120 ° 60 ° 30 ° 200 100 0 0 100 200 300 400 0 25 50 I F A V M [A ] 75 100 125 150 T A [°C ] Fig. 4 Power dissipation versus forward current and ambient temperature (per diode) 1600 R R thKA K/W L 0.06 0.08 0.10 0.15 0.20 0.30 0.40 0.50 1200 P to t [W ] 800 Circuit B2 2x MDD310 400 0 0 200 400 I d A V M [A ] 600 0 25 50 75 100 125 150 T A [°C ] Fig. 5 Single phase rectifier bridge: Power dissipation vs. direct output current and ambient temperature R = resistive load, L = inductive load IXYS reserves the right to change limits, test conditions and dimensions. © 2015 IXYS All rights reserved 20150910a 3-4 MDD 310 2500 R thKA K/W 0.03 0.05 0.06 0.08 0.12 0.15 0.2 0.3 2000 1500 1000 Circuit B6 3x MDD310 500 0 0 200 400 600 800 0 25 50 75 100 125 150 Fig.6 Three phase rectifier bridge: Power dissipation versus direct output current and ambient temperature 0.14 RthJC for various conduction angles d: 30° d DC 180° 120° 60° 30° DC 0.12 0.10 ZthJC 0.08 [K/W] RthJC [K/W] 0.129 0.131 0.132 0.132 0.133 0.06 Constants for ZthJC calculation: 0.04 0.02 0.00 10-3 10-2 10-1 100 101 t i [s] i Rthi [K/W] 1 0.0035 0.0099 2 0.0165 0.168 3 01091 0.456 t [s] Fig. 7 Transient thermal impedance junction to case (per diode) 0.20 RthJK for various conduction angles d: d DC 180° 120° 60° 30° 30° 0.16 DC ZthJK 0.12 [K/W] 0.08 RthJK (K/W) 0.169 0.171 0.172 0.172 0.173 Constants for ZthJK calculation: 0.04 0.00 10-3 10-2 10-1 100 101 i Rthi (K/W) t i (s) 1 0.0035 0.0099 2 0.0165 0.168 3 0.1091 0.456 4 0.04 1.36 t [s] Fig. 8 Transient thermal impedance junction to heatsink (per diode) IXYS reserves the right to change limits, test conditions and dimensions. © 2015 IXYS All rights reserved 20150910a 4-4