MLO36-12IO1

MLO 36 MMO 36 AC Controller Modules IRMS = 39 A VRRM = 1200-1600 V VRSM VDSM V VRRM VDRM V Type MLO G1 K1 MMO G1 K1 MMO 36 K1 G2 K2 G1 1200 1200 1600 1600 MLO 36-12io1 MLO 36-16io1 MMO 36-12io1 MMO 36-16io1 K2 K2 G2 Symbol IRMS ITRMS ITAVM ITSM Test Conditions TK = 85°C, 50 - 400 Hz (for single controller) TVJ = TVJM TK = 85°C; (180° sine) TVJ = 45°C; VR = 0 TVJ = TVJM VR = 0 t = 10 ms (50 Hz), sine t = 8.3 ms (60 Hz), sine t = 10 ms (50 Hz), sine t = 8.3 ms (60 Hz), sine t = 10 ms (50 Hz), sine t = 8.3 ms (60 Hz), sine t = 10 ms (50 Hz), sine t = 8.3 ms (60 Hz), sine Maximum Ratings 39 28 18 360 390 320 350 645 630 510 510 100 A A A A A A A A2s A2s A2s A2s A/ms A/ms V/ms W W W V °C °C °C V~ V~ Nm lb.in. g K1 = Cathode 1, G1 = Gate 1 K2 = Cathode 2, G2 = Gate 2 (MLO 36 has no G2 lead) I2t TVJ = 45°C VR = 0 TVJ = TVJM VR = 0 (di/dt)cr TVJ = TVJM repetitive, IT = 150 A f =50 Hz, tP =200 ms VD = 2/3 VDRM IG = 0.3 A non repetitive, IT = ITAVM diG/dt = 0.3 A/ms TVJ = TVJM; VDR = 2/3 VDRM RGK = ¥; method 1 (linear voltage rise) TVJ = TVJM IT = ITAVM tp = 30 ms tp = 300 ms Features Thyristor controller for AC (circuit W1C acc. to IEC) for mains frequency Direct copper bonded Al2O3 -ceramic base plate Isolation voltage 3600 V~ Planar passivated chips UL registered, E 72873 Long wire leads suitable for PC board soldering q q q q q q 500 1000 10 5 0.5 10 -40...+125 125 -40...+125 (dv/dt)cr PGM PGAVM VRGM TVJ TVJM Tstg VISOL Md Weight Applications Switching and control of single and three phase AC Softstart AC motor controller Solid state switches Light and temperature control q q q q q q q q Advantages Easy to mount with two screws Space and weight savings Improved temperature and power cycling High power density 50/60 Hz, RMS IISOL £ 1 mA Mounting torque typ. t = 1 min t=1s (M3) (UNF 4-32) 3000 3600 0.7 ± 0.1 6 ± 0.9 15 Data according to IEC 60747 and to a single thyristor/diode unless otherwise stated. IXYS reserves the right to change limits, test conditions and dimensions. © 2000 IXYS All rights reserved 1-3 MLO 36 MMO 36 Symbol IR, ID VT VT0 rT VGT IGT IGM VGD IGD IL IH tgd tq RthJC RthJK dS dA a Test Conditions TVJ = TVJM; VR = VRRM; VD = VDRM IT = 45 A; TVJ = 25°C Characteristic Values £ £ 5 1.49 0.85 15 £ £ £ £ £ £ £ £ £ typ. 1.0 1.15 65 120 6 0.2 1 150 100 2 150 1.3 0.65 1.5 0.75 6 6 50 mA V V mW V V mA mA A V mA mA mA ms 1000 0.1 1 10 100 1000 IG mA 4: PGAV = 0.5 W 5: PGM = 1 W 6: PGM = 10 W 10 V VG 1: IGT, TVJ = 125°C 2: IGT, TVJ = 25°C 3: IGT, TVJ = -40°C For power-loss calculations only VD = 6 V; VD = 6 V; TVJ = 25°C TVJ = -40°C TVJ = 25°C TVJ = -40°C 1 2 1 6 3 4 5 tp = 50 ms, f = 60 Hz, IT = ITAVM TVJ = TVJM; VD = 2/3 VDRM TVJ = 25°C; tP = 10 ms, VD = 6 V IG = 0.3 A; diG/dt = 0.3 A/ms TVJ = 25°C; VD = 6 V; RGK = ¥ TVJ = 25°C; VD = 1/2 VDRM IG = 0.3 A; diG/dt = 0.3 A/ms TVJ = TVJM; IT = 11 A, tP = 200 ms; -di/dt = 10 A/ms VR = 100 V; dv/dt = 10 V/ms; VD = 2/3 VDRM per per per per thyristor/diode; DC current module thyristor/diode; DC current module IGD, TVJ = 125°C Fig. 1 Gate trigger characteristics ms K/W K/W K/W K/W mm mm m/s2 tgd TVJ = 25°C µs typ. Limit 100 Creeping distance on surface Creepage distance in air Max. allowable acceleration 10 1 10 100 IG mA 1000 Dimensions in mm (1 mm = 0.0394") MLO 36 MMO 36 Fig. 2 Gate trigger delay time 160 A TVJ = 125°C TK = 85°C 140 IRMS 120 100 80 60 40 20 0 0.01 MMO 36 MLO 36 0.1 1 t s 10 Fig. 3 Rated RMS current versus time (360° conduction) © 2000 IXYS All rights reserved 2-3 MLO 36 MMO 36 60 W 50 Ptot 40 RthKA K/W 0.9 1.8 3 4.5 7.5 10.5 ITSM 300 250 200 150 TVJ = 125°C TVJ = 45°C 400 A 350 50 Hz 80 % VRRM 30 20 100 10 Circuit W1 1 x MMO 36 1 x MLO 36 0 5 10 15 20 25 30 35 40 A 0 IRMS 25 50 75 100 TA 125 °C 150 50 0 1 0 10 t 100 ms 1000 Fig. 4 Load current capability for single phase AC controller 180 W 160 Ptot140 120 100 80 60 40 20 0 0 5 10 15 20 25 30 35 40 A 0 IRMS 25 50 75 100 TA 125 °C 150 Circuit W3 3 x MMO 36 3 x MLO 36 RthKA K/W 0.3 0.6 1 1.5 2.5 3.5 Fig. 5 Surge overload current ITSM, IFSM: Crest value, t: duration 1000 VR = 0V A2s I2t TVJ = 125°C TVJ = 45°C 300 200 100 1 t ms 10 Fig. 6 Load current capability for three phase AC controller: 3xMMO 36/MLO 36 2.0 K/W 1.6 ZthJK 1.2 Constants for ZthJK calculation: Rthi / (K/W) ti / (s) 0.017 0.04 1.143 0.3 0.008 0.019 0.16 0.98 30° 60° 120° 180° DC Fig. 7 I2t versus time (1-10 ms) 30 A ITAVM 25 20 DC 180° sin 120° 60° 30° 0.8 RthJK for various conduction angles d : RthJK / (K/W) d: DC 180° 120° 60° 30° 15 10 0.4 1.5 1.557 1.579 1.603 1.616 5 0.0 0.001 0 0.01 0.1 1 10 t s 100 0 25 50 75 TK 100 125 °C Fig. 8 Transient thermal impedance junction to heatsink (per thyristor or diode) © 2000 IXYS All rights reserved Fig. 9 Maximum on-state current versus heatsink temperature 3-3