PAA140L

PAA140L 400V, 200mA Dual Single-Pole INTEGRATED CIRCUITS DIVISION Parameter Blocking Voltage Load Current On-Resistance (max) Rating 400 200 13 Normally Open, Current-Limiting Relays Units V mArms / mADC  Features • • • • • • • • Current Limiting 3750Vrms Input/Output Isolation Low Drive Power Requirements Greater Reliability than Electromechanical Relays No EMI/RFI Generation Small 8-Pin Package Flammability Rating UL 94 V-0 Tape & Reel Version Available Description PAA140L is a current-limited, dual, normally open (1-Form-A) solid state relay that uses optically coupled MOSFET technology to provide 3750Vrms of input to output isolation. Its optically coupled outputs, which use the patented OptoMOS architecture, are controlled by a highly efficient infrared LED. Featuring low on-resistance and very high load current handling capability, it is suitable for a variety of high performance switching applications. Approvals • UL Recognized Component: File # E76270 • CSA Certified Component: Certificate # 1175739 • TUV EN 62368-1: Certificate # B 082667 0008 Applications • Telecommunications • Telecom Switching • Tip/Ring Circuits • Modem Switching (Laptop, Notebook, Pocket Size) • Hook Switch • Dial Pulsing • Ground Start • Ringing Injection • Instrumentation • Multiplexers • Data Acquisition • Electronic Switching • I/O Subsystems • Meters (Watt-Hour, Water, Gas) • Medical Equipment-Patient/Equipment Isolation • Security • Industrial Controls Ordering Information Part # PAA140L PAA140LS PAA140LSTR Description 8-Lead DIP (50/tube) 8-Lead Surface Mount (50/tube) 8-Lead Surface Mount (1000/Reel) Pin Configuration + Control - Switch #1 – Control - Switch #1 + Control - Switch #2 – Control - Switch #2 1 8 2 7 3 6 4 5 Load - Switch #1 Load - Switch #1 Load - Switch #2 Load - Switch #2 Switching Characteristics of Normally Open Devices Form-A IF 90% 10% ILOAD ton DS-PAA140L-R06 www.ixysic.com toff 1 INTEGRATED CIRCUITS DIVISION PAA140L Absolute Maximum Ratings @ 25ºC Parameter Blocking Voltage Reverse Input Voltage Input Control Current Peak (10ms) Input Power Dissipation 1 Total Power Dissipation 2 Isolation Voltage, Input to Output Operational Temperature, Ambient Storage Temperature 1 Derate linearly 1.33 mW / ºC 2 Derate output power linearly 6.67 mW / ºC Ratings 400 5 50 1 150 800 3750 -40 to +85 -40 to +125 Absolute Maximum Ratings are stress ratings. Stresses in excess of these ratings can cause permanent damage to the device. Functional operation of the device at conditions beyond those indicated in the operational sections of this data sheet is not implied. Units VP V mA A mW mW Vrms °C °C Typical values are characteristic of the device at +25°C, and are the result of engineering evaluations. They are provided for information purposes only, and are not part of the manufacturing testing requirements. Electrical Characteristics @ 25ºC Parameter Output Characteristics Blocking Voltage Load Current 1 Continuous Peak Current Limit On-Resistance 2 Off-State Leakage Current Switching Speeds Turn-On Turn-Off Output Capacitance Input Characteristics Input Control Current to Activate Input Control Current to Deactivate Input Voltage Drop Reverse Input Current Common Characteristics Capacitance, Input to Output Conditions Symbol Min Typ Max Units IL=1A VDRM 400 - - VP t=10ms IF=5mA IL=200mA VL=400VP IL ILPK ICL RON ILEAK 240 - 10 - 200 ±500 380 13 1 mArms / mADC mAP mArms / mADC  A IF=0mA, VL=50V, f=1MHz ton toff COUT - 65 5 3 - IL=200mA IF=5mA VR=5V IF IF VF IR 0.4 0.9 - 0.7 1.36 - 5 1.5 10 mA mA V A VIO=0V, f=1MHz CIO - 3 - pF IF=5mA, VL=10V 1 If both poles operate simultaneously, then load current must be derated in order not to exceed the package power dissipation value. 2 Measurement taken within one second of on-time. 2 www.ixysic.com ms pF R06 INTEGRATED CIRCUITS DIVISION PAA140L PERFORMANCE DATA* Typical LED Forward Voltage Drop (N=50, IF=5mA) 25 Device Count (N) 20 15 10 5 15 10 5 0 0 1.364 0.39 Device Count (N) 15 10 5 0 0.65 0.91 1.17 1.43 1.69 Turn-On Time (ms) 2.1 2.7 3.3 3.9 LED Current (mA) 4.5 10 5 0.018 0.030 0.042 0.054 0.066 0.078 0.090 Turn-Off Time (ms) Typical On-Resistance Distribution (N=50, IF=5mA, IL=200mADC) 35 30 20 15 10 5 25 20 15 10 5 0 1.5 15 1.95 Typical IF for Switch Dropout (N=50, IL=200mADC) 25 20 20 0 1.366 1.368 1.370 1.372 LED Forward Voltage Drop (V) Typical IF for Switch Operation (N=50, IL=200mADC) 25 Device Count (N) 20 Device Count (N) Device Count (N) 25 Typical Turn-Off Time (N=50, IF=5mA, IL=200mADC) 25 Device Count (N) 30 Typical Turn-On Time (N=50, IF=5mA, IL=200mADC) 0 5.1 0.9 1.5 2.1 2.7 3.3 LED Current (mA) 3.9 4.5 5.03 5.38 5.73 6.08 6.43 6.78 On-Resistance (:) 7.13 Typical Blocking Voltage Distribution (N=50) 35 Device Count (N) 30 25 20 15 10 5 0 430 1.6 IF=10mA IF=5mA IF=2mA 1.5 1.4 1.3 1.2 1.1 1.0 -50 -25 0 25 50 Temperature (ºC) 75 100 502 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 Turn-Off Time (ms) Turn-On Time (ms) LED Forward Voltage Drop (V) 1.7 454 466 478 490 Blocking Voltage (VP) Typical Turn-On Time vs. LED Forward Current (IL=200mADC) Typical LED Forward Voltage Drop vs. Temperature 1.8 442 0 5 10 15 20 25 30 35 40 LED Forward Current (mA) 45 50 Typical Turn-Off Time vs. LED Forward Current (IL=200mADC) 0.050 0.045 0.040 0.035 0.030 0.025 0.020 0.015 0.010 0.005 0 0 5 10 15 20 25 30 35 40 LED Forward Current (mA) 45 50 *Unless otherwise noted, data presented in these graphs is typical of device operation at 25ºC. R06 www.ixysic.com 3 INTEGRATED CIRCUITS DIVISION PAA140L PERFORMANCE DATA* Typical Turn-On Time vs. Temperature (IL=250mADC) 0.07 IF=5mA IF=10mA IF=20mA 1.5 1.0 0.5 0.05 0.04 0.03 0.02 0.01 0 -40 -20 0 20 40 60 Temperature (ºC) 80 0 -40 100 Typical IF for Switch Operation vs. Temperature (IL=150mADC) 5.0 0 20 40 60 Temperature (ºC) 80 100 3.5 3.0 2.5 Load Current (mA) 4.0 4.0 3.5 3.0 2.5 2.0 2.0 1.5 -40 1.5 -20 0 20 40 60 Temperature (ºC) 80 -40 100 -20 0 20 40 60 Temperature (ºC) 80 100 200 I F =10mA I F =5mA I F =10mA I F =5mA 50 -40 -20 0 20 40 60 80 Temperature (ºC) 100 250 200 150 100 50 0 -50 -100 -150 -200 -250 -2.0 -1.5 0 20 40 60 Temperature (ºC) 80 100 1.5 2.0 Typical Load Current vs. Load Voltage (IF=5mA) -1.0 -0.5 0 0.5 1.0 Load Voltage (V) 0.10 475 470 465 460 0.08 0.06 0.04 455 0.02 450 445 -40 120 -20 0.12 480 Leakage (PA) One Pole Operating Blocking Voltage (VP) 250 Two Poles Operating One Pole Operating Two Poles Operating Typical Leakage vs. Temperature Measured across Pins 5&6 or 7&8 485 300 100 20 18 16 14 12 10 8 6 4 2 0 Typical Blocking Voltage vs. Temperature Maximum Load Current vs. Temperature 150 Typical On-Resistance vs. Temperature (IF=5mA, IL=200mADC) -40 4.5 LED Current (mA) LED Current (mA) -20 Typical IF for Switch Dropout vs. Temperature (IL=150mADC) 5.0 4.5 Load Current (mA) On-Resistance (:) 2.0 0.06 Turn-Off Time (ms) Turn-On Time (ms) 2.5 Typical Turn-Off Time vs. Temperature (IF=5mA, IL=250mADC) -20 0 20 40 60 Temperature (ºC) 80 100 10s 100s 0 -40 -20 0 20 40 60 Temperature (ºC) 80 100 Energy Rating Curve 1.2 Load Current (A) 1.0 0.8 0.6 0.4 0.2 0 10Ps 100Ps 1ms 10ms 100ms Time 1s *Unless otherwise noted, data presented in these graphs is typical of device operation at 25ºC. 4 www.ixysic.com R06 INTEGRATED CIRCUITS DIVISION PAA140L Manufacturing Information Moisture Sensitivity All plastic encapsulated semiconductor packages are susceptible to moisture ingression. IXYS Integrated Circuits classifies its plastic encapsulated devices for moisture sensitivity according to the latest version of the joint industry standard, IPC/JEDEC J-STD-020, in force at the time of product evaluation. We test all of our products to the maximum conditions set forth in the standard, and guarantee proper operation of our devices when handled according to the limitations and information in that standard as well as to any limitations set forth in the information or standards referenced below. Failure to adhere to the warnings or limitations as established by the listed specifications could result in reduced product performance, reduction of operable life, and/or reduction of overall reliability. This product carries a Moisture Sensitivity Level (MSL) classification as shown below, and should be handled according to the requirements of the latest version of the joint industry standard IPC/JEDEC J-STD-033. Device Moisture Sensitivity Level (MSL) Classification PAA140LS MSL 1 ESD Sensitivity This product is ESD Sensitive, and should be handled according to the industry standard JESD-625. Soldering Profile Provided in the table below is the IPC/JEDEC J-STD-020 Classification Temperature (TC) and the maximum total dwell time (tP) in all reflow processes that the body temperature of these surface mount devices may be (TC - 5)°C or greater. The device’s body temperature must not exceed the Classification Temperature at any time during reflow soldering processes. Device Classification Temperature (Tc) Dwell Time (tP) Max Reflow Cycles PAA140LS 250ºC 30 seconds 3 For through-hole devices, the maximum pin temperature and maximum dwell time through all solder waves is provided in the table below. Dwell time is the interval beginning when the pins are initially immersed into the solder wave until they exit the solder wave. For multiple waves, the dwell time is from entering the first wave until exiting the last wave. During this time, pin temperatures must not exceed the maximum temperature given in the table below. Body temperature of the device must not exceed the limit shown in the table below at any time during the soldering process. Device PAA140L Maximum Pin Temperature 260ºC Maximum Body Temperature 250ºC Maximum Dwell Time 10 seconds* Wave Cycles 1 *Total cumulative duration of all waves. Board Wash IXYS Integrated Circuits recommends the use of no-clean flux formulations. Board washing to reduce or remove flux residue following the solder reflow process is acceptable provided proper precautions are taken to prevent damage to the device. These precautions include but are not limited to: using a low pressure wash and providing a follow up bake cycle sufficient to remove any moisture trapped within the device due to the washing process. Due to the variability of the wash parameters used to clean the board, determination of the bake temperature and duration necessary to remove the moisture trapped within the package is the responsibility of the user (assembler). Cleaning or drying methods that employ ultrasonic energy may damage the device and should not be used. Additionally, the device must not be exposed to halide flux or solvents. R06 www.ixysic.com 5 INTEGRATED CIRCUITS DIVISION PAA140L Mechanical Dimensions PAA140L 2.540 ± 0.127 (0.100 ± 0.005) 9.652 ± 0.381 (0.380 ± 0.015) 8-0.762 DIA. (8-0.030 DIA.) 2.540 ± 0.127 (0.100 ± 0.005) 9.144 ± 0.508 (0.360 ± 0.020) 6.350 ± 0.127 (0.250 ± 0.005) Pin 1 PCB Hole Pattern 7.620 ± 0.254 (0.300 ± 0.010) 0.457 ± 0.076 (0.018 ± 0.003) 3.302 ± 0.051 (0.130 ± 0.002) 7.620 ± 0.127 (0.300 ± 0.005) 7.239 TYP. (0.285) 4.064 TYP (0.160) 0.254 ± 0.0127 (0.010 ± 0.0005) 7.620 ± 0.127 (0.300 ± 0.005) Dimensions mm (inches) 0.813 ± 0.102 (0.032 ± 0.004) PAA140LS PCB Land Pattern 9.652 ± 0.381 (0.380 ± 0.015) 2.540 ± 0.127 (0.100 ± 0.005) 6.350 ± 0.127 (0.250 ± 0.005) Pin 1 0.635 ± 0.127 (0.025 ± 0.005) 3.302 ± 0.051 (0.130 ± 0.002) 9.525 ± 0.254 (0.375 ± 0.010) 0.457 ± 0.076 (0.018 ± 0.003) 2.54 (0.10) 8.90 (0.3503) 1.65 (0.0649) 7.620 ± 0.254 (0.300 ± 0.010) 0.254 ± 0.0127 (0.010 ± 0.0005) 0.65 (0.0255) 4.445 ± 0.127 (0.175 ± 0.005) Dimensions mm (inches) 0.813 ± 0.102 (0.032 ± 0.004) 6 www.ixysic.com R06 INTEGRATED CIRCUITS DIVISION PAA140L PAA140LSTR Tape & Reel 2.0 (0.08) 4.0 (0.16) 330.2 DIA. (13.00 DIA.) Top Cover Tape Thickness 0.102 MAX. (0.004 MAX.) 7.5 (0.30) Bo=10.30 (0.406) K0 =4.90 (0.193) K1 =4.20 (0.165) Embossed Carrier Embossment 16.0±0.3 (0.63±0.012) Ao=10.30 (0.406) P1=12.00 (0.472) User Direction of Feed Dimensions mm (inches) NOTES: 1. Dimensions carry tolerances of EIA Standard 481-2 2. Tape complies with all “Notes” for constant dimensions listed on page 5 of EIA-481-2 3. Controlling dimension: mm For additional information please visit our website at: https://www.ixysic.com Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at https://www.littelfuse.com/disclaimer-electronics. 7 Specification: DS-PAA140L-R06 ©Copyright 2021, Littelfuse, Inc. OptoMOS® is a registered trademark of IXYS Integrated Circuits All rights reserved. Printed in USA. 11/4/2021