DX4R0W5HJ1R1300

COMPONENTS PRODUCT INFORMATION NEW USB 2.0 Compatible Micro Connectors CONNECTOR MB-0187-3 December 2014 DX4 Series RoHS Compliant On-board Type Mid-mount Type The DX4 Series is a set of connectors compatible with the Micro-USB type USB 2.0 for small devices standardized by the USB Implementers Forum, Inc. Features Compatible with Universal Serial Bus Micro-USB Cables and Connectors Specification, Revision 1.01. Connector type: USB 2.0 compatible, Micro types Au plating over Pd-Ni alloy is used for mating cycle durability and long product life. Superior rigidity with high-strength stainless steel shell. Available in a variety of versions to suit diverse device configurations. Two-piece shell structure for mid-mount type to prevent contact failure due to flux scattering during reflow. Available in reinforced type, with reinforcement plate set in mating area to prevent damage from plug caused by misaligned mating. (Refer to drawing below) Reinforcement plate of mating area Mating Area Reinforced Type *In the above drawing the shell is transparent for illustration purposes to show the reinforcement plate. General Specifications No. of Contacts: 5 positions Contact Resistance: 30m ohm max. (initial) Dielectric Withstanding Voltage: AC500Vrms per minute Insulation Resistance: 1000M ohm (initial) Rated Current: DC1.8A (Vbus, GND) Others DC0.5A Rated Voltage: AC30Vrms Durability: 10,000 mating cycles Operating temperature: -30 Deg. C to +80 Deg. C JAE PMK Div. Proprietary. Copyright © 2014, Japan Aviation Electronics Industry, Ltd. 1/10 MB-0187-3 Materials and Finishes Component Material and Finish Insulator Synthetic Resin Contact Copper alloy / Contact area: Au flash plating over Pd-Ni alloy over Ni Terminal area: Au flash plating over Ni Shell Stainless Steel / Sn plating over Ni *For more information please refer to individual product drawings. Ordering Information DX4 R 0 05 J J 2 R1800 Reel: 1800 pcs. / reel Series DX4: USB2.0 Micro Modification Code: #2 R: Receptacle Plating Specification J: Contact area: Au flash over Pd-Ni alloy over Ni Modification Code: #1 Board Connection Type (Shell area) J: Through-hole type, H: Hold-down type No. of Contacts: 5 pos. Micro-USB Connector Type Type B Type AB SJ Drawing Specificat ion DX4R005JJ2 (Individual Unit) SJ110578 DX4R005JJ2R1800 (Reel Unit) SJ110579 JACS30162 DX4R005HJ5 (Individual Unit) SJ111770 DX4R005HJ5R2000 (Reel Unit) SJ111771 DX4R005JJ6 (Individual Unit) SJ112420 DX4R005JJ6R1500 (Reel Unit) SJ112421 DX4R005JJ7 (Individual Unit) SJ112422 DX4R005JJ7R1500 (Reel Unit) SJ112423 DX4RN05JJ3 (Individual Unit) SJ112800 DX4RN05JJ3R2000 (Reel Unit) SJ112801 DX4R105JJC (Individual Unit) SJ113218 DX4R105JJCR1800 (Reel Unit) SJ113219 DX4R205JJA (Individual Unit) SJ112925 DX4R205JJAR1800 (Reel Unit) SJ112926 DX4R305JJB (Individual Unit) SJ112927 DX4R305JJBR1800 (Reel Unit) SJ112928 DX4R205JJ8 (Individual Unit) SJ112802 DX4R205JJ8R2000 (Reel Unit) SJ112803 DX4R205JJ9 (Individual Unit) SJ112804 DX4R205JJ9R2000 (Reel Unit) SJ112805 Part Number Mounting Type Mating Taper Mating Area Reinforcement Plate Yes On-board JACS30185 No JACS30251 JACS30252 Standard Mid-mount No JACS30257 No JACS30281 JACS30267 Reverse On-board Yes Standard No JACS30268 Reverse JACS30258 JACS30259 Yes No (Standard Type) Yes (Mating Area Reinforced Type) Yes Mid-mount Standard No Note: Please place orders in reel units. JAE PMK Div. Proprietary. Copyright © 2014, Japan Aviation Electronics Industry, Ltd. 2/10 MB-0187-3 Standard Type (Micro-B): DX4R005JJ2 Unit: mm JAE PMK Div. Proprietary. Copyright © 2014, Japan Aviation Electronics Industry, Ltd. 3/10 MB-0187-3 Standard Type (Micro-B): DX4R005HJ5 Unit: mm JAE PMK Div. Proprietary. Copyright © 2014, Japan Aviation Electronics Industry, Ltd. 4/10 MB-0187-3 Standard Type (Micro-B): DX4R005JJ6 Unit: mm Type without mating area taper (DX4R005JJ7) *Design is same as DX4R005JJ6 except the mating area taper. JAE PMK Div. Proprietary. Copyright © 2014, Japan Aviation Electronics Industry, Ltd. 5/10 MB-0187-3 Mating Area Reinforced Type (Micro-B): DX4RN05JJ3 Unit: mm JAE PMK Div. Proprietary. Copyright © 2014, Japan Aviation Electronics Industry, Ltd. 6/10 MB-0187-3 Mating Area Reinforced Type (Micro-B): DX4R105JJC Unit: mm 寸法単位：[mm] JAE PMK Div. Proprietary. Copyright © 2014, Japan Aviation Electronics Industry, Ltd. 7/10 MB-0187-3 Mating Area Reinforced Type (Micro-AB): DX4R205JJA Unit: mm JAE PMK Div. Proprietary. Copyright © 2014, Japan Aviation Electronics Industry, Ltd. 8/10 MB-0187-3 Mating Area Reinforced Type (Micro-AB): DX4R305JJB Unit: mm JAE PMK Div. Proprietary. Copyright © 2014, Japan Aviation Electronics Industry, Ltd. 9/10 MB-0187-3 Mating Area Reinforced Type (Micro-AB): DX4R205JJ8 Type without mating area taper (DX4R205JJ9) *Design is same as DX4R205JJ8 except the mating area taper. Unit: mm Notice: 1. The values specified in this brochure are only for reference. The products and their specifications are subject to change without notice. Contact our sales staff for further information before considering or ordering any of our products. For purchase, a product specification must be agreed upon. 2. Users are requested to provide protection circuits and redundancy circuits to ensure safety of the equipment, and sufficiently review the suitability of JAE's products to the equipment. 3. The products presented in this brochure are designed for the uses recommended below. We strongly suggest you contact our sales staff when considering use of any of the products in any other way than the recommended applications or for a specific use that requires an extremely high reliability. (1) Applications that require consultation: (i) Please contact us if you are considering use involving a quality assurance program that you specify or that is peculiar to the industry, such as: Automotive electrical components, train control, telecommunications devices (mainline), traffic light control, electric power, combustion control, fire prevention or security systems, disaster prevention equipment, etc. (ii) We may separately give you our support with a quality assurance program that you specify, when you think of a use such as : Aviation or space equipment, submarine repeaters, nuclear power control systems, medical equipment for life support, etc. (2) Recommended applications include: Computers, office appliances, telecommunications devices (terminals, mobile units), measuring equipment, audiovisual equipment, home electric appliances, factory automation equipment, etc Product Marketing Division Aobadai Building, 3-1-19, Aobadai, Meguro-ku, Tokyo 153-8539 Phone: +81-3-3780-2882 FAX: +81-3-3780-2946 * The specifications in this brochure are subject to change without notice. Please contact JAE for information. JAE PMK Div. Proprietary. Copyright © 2014, Japan Aviation Electronics Industry, Ltd. 10/10