ETX100RSC-DM

COMMUNICATIONS COMPONENTS High Speed InGaAs Photodetector Receptacle Modules ETX 100 Key Features • Electro-optical - High responsivity at 1310 and 1550 nm - Bandwidth greater than 1 GHz - High sensitivity • Packaging - Small surface area, LC receptacle for PC boards - FC coaxial receptacle for panel mounts - Direct-mating SC receptacle for PC boards or panel mounts Applications • Fiberoptics telecommunication networks • Digital receivers • Optical interconnects • Test and measurement • Datacom • LAN The ETX 100Rxx series are high speed receptacled photodiode modules designed primarily for use in optical communications applications in which high speed and reliability are critical. These modules feature bandwidths of at least 1 GHz and are designed for peak wavelength response at 1300 and 1550 nm. The connector receptacle designs permit mounting on PC boards or back planes. Each of the four modules making up the ETX 100Rxx series incorporates a 100 µm diameter InGaAs PIN photodiode mounted in an industry standard, precision connector receptacle which assures excellent mating repeatability. Standard receptacles available include LC, FC, and SC. These modules will accept either Single Mode or Multi Mode connectorized fiber. The ETX 100 RLC is mounted in an LC receptacle and is designed primarily to provide a high performance package for telecommunication and datacom applications with reduced surface density and easier mounting procedures. This next generation small form factor (The LC receptacle is respectively, 52% and 34%, smaller in packaging surface density than the FC and SC receptacles) is half the footprint required for LAN interfaces, thereby reducing costs and increasing packing density. Like the RSC, the ETX 100 RLC mates directly with the connector and does not require fastening of the connector to assure mating. All receptacled detector modules are qualified to Telecordia and MIL standards. NORTH AMERICA : 800 498-JDSU (5378) WORLDWIDE : +800 5378-JDSU WEBSITE : www.jdsu.com HIGH SPEED INGAAS PHOTODETECTOR RECEPTACLE MODULES 2 Dimensions Diagram (Specifications in mm unless otherwise noted.) ETX 100RLC Electrical Schematic 2 1 PD 3 13.1 ETX 100RFC2 TOP VIEW 19.0 13.45 2.2 dia. holes with 4.0 dia. counterbore. 1.5 deep 9.20 M8 x 0.75 17.78 20.45 7.0 25.40 6.0 2.0 5.40 Leads (0.42 O.D. Typ.) Electrical Schematic R9.50 1 PD 3 2 7.8 2.67 13.5 25.4 5.60 Dia. 1.27 7.5 3 2 1 2 9.6 5.60 Dia. Pin circle Dia., 2.54 1.27 3 1 Pin circle Dia., 2.54 Bottom View Bottom View ETX 100RSC-DM TOP VIEW 22.0 18.0 ETX 100RSC-FM TOP VIEW 22.0 18.0 (2) Thru Holes 2.3 dia. (2) Thru Holes 2.30 dia. 9.20 9.20 12.75 6.80 19.45 12.3 15.2 3 Leads (0.42 O.D. Typ.) 12.75 19.8 12.3 15.2 3 Leads (0.42 O.D. Typ.) 4.20 25.4 Typ. (2) Thru Holes 2.2 dia. Electrical Schematic 1 PD 2 25.4 Typ. 5.41 Electrical Schematic 1 PD 2 1.27 7.0 3 21 1.27 7.0 3 21 3 3 Pin circle Dia., 2.54 BOTTOM VIEW Pin circle Dia., 2.54 BOTTOM VIEW Note: Critical dimensions meet NTT specifications. Other dimensions subject to revision. Note: Critical dimensions meet NTT specifications. Other dimensions subject to revision. HIGH SPEED INGAAS PHOTODETECTOR RECEPTACLE MODULES 3 Figure 1 Figure 2 Typical Spectral Response 23 ˚C 1.0 1E-07 Dark Current Reverse Current (A) 0.8 @ 80˚C 1E-08 Responsivity (A/W) @ 50˚C 1E-09 0.6 @ 25˚C 1E-10 0.4 1E-11 0.2 0 5 10 15 20 25 Reverse Voltage 0.0 800 1000 1200 1400 1600 1800 Wavelength (nm) Figure 3 Capacitance vs. Voltage 2.25 Figure 4 Bandwidth 2 Normalized Response (dB) 1 0 -1 -2 -3 -4 -5 -6 -7 Capacitance (pF) 1.75 1.25 .75 0.25 0 5 10 15 20 -8 10 100 1000 2000 Reverse Voltage Frequency (MHz) HIGH SPEED INGAAS PHOTODETECTOR RECEPTACLE MODULES 4 Specifications (Temperature = 25°C, VR = 5 V unless noted.) Parameter Active diameter Responsivity Conditions λ = 1310 nm1 λ = 1550 nm1 Typical Minimum Typical Minimum Typical Maximum Typical Maximum Typical Typical Specification 100 µm 0.65 A/W 0.75 A/W 0.70 A/W 0.30 nA 1.0 nA 1.1 pF 1.25 pF 1.5 GHz 250 ps Dark current Capacitance2 Bandwidth3 Rise time4 1. Measured with 50 µm, 0.2 N.A., graded index fiber. 2. Measured with case grounded. 3. -3 dB point into a 50 Ω load. 4. RLOAD = 50 Ω. Maximum Ratings Parameter Forward current1 Reverse current2 Reverse voltage Operating case temperature Storage temperature Maximum Maximum Maximum Minimum Maximum Minimum Maximum Specification 10 mA 10 mA 25 V -40°C 85°C -40°C 85°C 1. Under forward bias, current at which device may be damaged. 2. Under reverse bias, current at which device may be damaged. HIGH SPEED INGAAS PHOTODETECTOR RECEPTACLE MODULES Ordering Information For more information on this or other products and their availability, please contact your local JDSU account manager or JDSU directly at 1-800-498-JDSU (5378) in North America and +800-5378-JDSU worldwide or via e-mail at customer.service@jdsu.com. Sample: ETX 100 RLC ETX 100 + Code RLC RFC2 RSC-DM RSC-FM Package LC receptacle FC receptacle with 2-hole flange SC receptacle, dual-mount (panel & board) SC receptacle, front-mount (panel only) Precautions for Use ESD protection is imperative. Use of grounding straps, anti-static mats, and other standard ESD protective equipment is required when handling or testing an InGaAs PIN or any other junction photodiode. Fiber pigtails should be handled with less than 10 N pull and with bending radius greater than 1 inch. Soldering temperature of the leads should not exceed 260 °C for more than 10 seconds. All statements, technical information and recommendations related to the products herein are based upon information believed to be reliable or accurate. However, the accuracy or completeness thereof is not guaranteed, and no responsibility is assumed for any inaccuracies. The user assumes all risks and liability whatsoever in connection with the use of a product or its application. JDSU reserves the right to change at any time without notice the design, specifications, function, fit or form of its products described herein, including withdrawal at any time of a product offered for sale herein. JDSU makes no representations that the products herein are free from any intellectual property claims of others. Please contact JDSU for more information. JDSU and the JDSU logo are trademarks of JDS Uniphase Corporation. Other trademarks are the property of their respective holders. ©2006 JDS Uniphase Corporation. All rights reserved. 30137544 Rev. 001 05/06 ETX100.DS.CC.AE N ORTH AMERICA : 800 498-JDSU (5378) WORLDWIDE : +800 5378-JDSU WEBSITE : www.jdsu.com