RoHS 对应品
发行日期
Date:
2019 年 12 月 03 日
Dec.03. 2019
编 号 NO
GGSD2019875
版本 Edition
A
产 品 规 格 书
Product specification
产品名称: 铝电解电容器
Products Name: Aluminum Electrolytic capacitor
产品系列: CD297 系列
Products Series:CD297 Series
客户名 Customer:
深圳市立创电子
客户 Customer P/NO:
客户 Customer SPEC:
南 通 江 海 电 容 器 股 份 有 限 公 司
Nantong Jianghai Capacitor Co.,Ltd
制
作
审
核
批
准
Designed
Checked
Approved
季张林
丰骏
丁继华
User 承认栏
地址:江苏省南通市平潮镇通杨南路 79 号
ADD: NO.79, Tongyang South Road, Pingchao Town, Nantong City ,Jiangsu
Province, P.R. China
TEL: 0086-0513-86726086
FAX: 0086-0513-86571812
P.C. 226361
E-MAIL: djh@jianghai.com,jzl@jianghai.com
南通江海电容器股份有限公司
-1-
ALUMINUM ELECTROLYTIC CAPACITOR
APPROVAL NO:
RECORD OF REVISION
REV. NO.
A
REASON
初版First Edition
DATE
REMARKS
20191203
南通江海电容器股份有限公司
-2-
规格表 SPEC LIST FOR CD297 SERIES
Customer P/N
JIANGHAI PART NUMBEER
ECS2GBB221MLA220050V
Ur
Cr(μF,
tolerance
tanδ(%,
Lc(μA,
(V)
120Hz,20℃)
(120Hz,20℃)
120Hz,20℃)
20℃,5min)
400
220
±20%
15
880
南通江海电容器股份有限公司
Rated ripple
(Arms,
105℃,120Hz)
0.79
Load life
D×L
(hrs, 105℃)
(mm×mm)
5000
22×50
-3-
1、适用范围 Adapt Range
本产品规格书适用于南通江海电容器股份有限公司 CD297 型铝电解电容器
产品,该产品满足 GB/T2693-2001 和 JIS C 5102-1994 的要求。
This product specification is adapted to CD297 series Aluminum
Electrolytic Capacitors produced according to GB/T2693-2001and JIS C
5102-1994 by Nantong jianghai Capacitor Co.,Ltd
2、使用温度范围 Operating Temperature Range
-40~105℃:10~350V, -25~105℃:400~550V
3、浪涌电压 Surge voltage
工作电压(v)
Rated voltage
浪涌电压(v)
Surge voltage
10
16
25 35
50
63
80 100 160 180 200 250 350 400 450 500 550
13
20
32 44
63
79 100 125 200 225 250 300 400 450 500 550 600
4、损耗 Dissipation factor
工作电压(v)
Rated voltage
损耗(%)
Dissipation factor
10
16
25
35
50
63
80
100
160~400
450~550
55
50
45
40
35
30
25
20
15
20
5、表示 Marking
NO.
1
2
3
项目 Item
额定电压 Rated voltage
静电容量 Capacitance
极性
Polarity
NO.
4
5
6
南通江海电容器股份有限公司
项目 Item
商标
Brand
上限温度 Max temperature
产品系列 Products series
-4-
6、外型图 Dimensions
7、纹波电流系数 Multiplier for ripple current
7.1、频率系数 Frequency Coefficients
Freq(Hz)
Rated
50/60
120
500
1K
voltage (v)
10~100
0.90
1.00
1.10
1.15
160~250
0.80
1.00
1.20
1.30
≥315
0.80
1.00
1.20
1.30
7.2、温度系数 Temperature Coefficients
温度 Temperature(℃)
+40
+55
+70
系数 Coefficients
2.7
2.5
2.1
10K
≥40K
1.15
1.45
1.42
1.15
1.50
1.45
+85
1.7
+105
1.0
8、 构造图及材料表(Frame drawing and Material table)
8.1、构造图(Frame drawing)
8.2、芯包分解图(Element drawing)
南通江海电容器股份有限公司
-5-
8.3、材料表(Material Table)
构成部件
Parts
材质
Material
1
铝壳
Case
铝
Aluminum
2
套管
Sleeve
PVC
No
3
封口板
End seal
board
4
隔离纸
Separator
覆胶板(EPT)
Rubber
Bakelite
黄铜镀锡
Brass
Electroplate
with TIN
电解电容器纸
Electrolytic
Capacitors
Paper
供应商
Supply
Factory
海邦电子
中天配件
No
构成部件
Parts
材质
Material
供应商
Supply
Factory
5
引线条
Lead Tab
铝
Aluminum
JCC
无等高新,
苏州顺鹏
6
正极箔
Anode Foil
铝
Aluminum
内蒙海立,
海昱电子,
凤翔海源
海邦电子,
嘉能电子
7
负极箔
Cathode Foil
铝
Aluminum
K-JCC,
BECROMAL
NKK,
KAN
8
电解液
Electrolyte
有机溶剂
Organic
Solvent
江海电容器有
限公司
南通江海电容器股份有限公司
-6-
9、性能特征:Specifications
性能特性: Performance characteristics
NO
项目 Items
条件 Conditions
技术要求
Specifications
9.1
静电容量
(允许偏差 )
Capacitance
( Tolerance )
测试频率:120 Hz,
Measuring frequency: 120 Hz
测试电压:0.5Vrms or less
Measuring voltage: 0.5Vrms or less
DC bias voltage: +1.5~ 2.0 VDC
见系列规格表
Refer to SPEC LIST
9.2
损耗角正切
(Tanδ)
Tangent of angle
测试条件与静电容量相同
Measurement shall be made under the same
conditions as those given for the
measurement of capacitance
见4
Refer to 4.
9.3
漏电流
Leakage Current
电容器接 1000±10Ω.的保护电阻施加电压 5
分钟后的测试电流。
The rated voltage shall be applied across
the capacitor and its protective resistor
which shall be 1000 ± 10 Ω .The leakage
Current shall then be measured after an
electrification period of 5min. The
leakage current shall be calculated by the
following equation.
漏电流:
(I)=E/Rs
Leakage current:
E:直流电压表的电压值
Voltage measured with DC voltmeter
RS:标准电阻的电阻值
Resistance of the protective resistor
测定电路 measurement circuit
0.01CV 或 1.5mA 以下(取小
值)
Less than 0.01CV or 1.5mA
whichever is smaller
C:标称静电容量(μF )
Capacitance
V:额定电压(V)
Rated voltage
9.4
额定纹波电流
Rated ripple current
电压降法(voltage drop method)
RS:标准电阻的电阻值(1000±10Ω)
RS: Protective resistor (1000±10Ω)
V1\V2:直流电压表或电子电压表
V1\V2:DC voltmeter or electronic voltmeter
S1:开关 switch
S2:电压表保护用变换开关 Protective switch
for a voltmeter and the test capacitor
温度 Temperature :105±2℃
南通江海电容器股份有限公司
见系列规格表
Refer to SPEC LIST
-7-
信赖性试验:The reliability test
NO
9.5
9.6
项目 Items
浪涌电压
Surge
Voltage
防爆试验
Safety
vent Test
条件
Conditions
在下面规定的温度下,通过指定的浪涌电压,6.0 分
钟(充电 30 秒,放电 5 分 30 秒)为一周期,共 1000
次,常温常湿下放置 1-2 小时,达到热平衡状态再进
行测定
The capacitor shall be subjected to 1000 cycles
at a temperature specified below, each consisting
of a charge period of 30 ± 5s, followed by a
discharge period of approx 5min.30 s. And the
capacitor shall be stored 1-2 hours under
standard atmospheric conditions to obtain
thermal stability , after which measurement shall
be made
测试电压:见 3
Test voltage: see 3
温度:15~35℃
Test Temperature : 15~35℃
测试回路 Measurement circuit
电压降法(voltage drop method)
RS:标准电阻的电阻值(1000±10Ω)
RS: Protective resistor (1000±10Ω)
V1\V2:直流电压表或电子电压表
V1\V2:DC voltmeter or electronic voltmeter
S1:开关 switch
S2:电压表保护用变换开关 Protective switch for a
voltmeter and the test capacitor
施加反向直流电流。
Apply a reverse voltage with DC current.
壳号
Size
逆向电流
Inverse current
≤φ22
1A
>φ22
10A
南通江海电容器股份有限公司
技术要求 Specifications
漏电流:不超过规定值
Leakage Current:
Not more than the specified
value
容量变化:初始值的±15%以内
Capacitance change:
Within ±15% of the initial
value
损耗角正切:不超过规定值
Dissipation Factor :
Within the initial specified
value
当防爆阀动作时,电容器应无打
火、击穿、燃烧等现象。如果防
爆阀 30 分钟未动作,则认为产
品合格。
When the vent operated, the
capacitor shall not flame
although gas discharge or
expulsion of a part of the
inside element is allowable.
If the vent does not operate
with the voltage applied for
30 minutes, the test is
considered to be passed.
-8-
No.
项目 Items
条件
9.7
高温负荷
Load life
在 105±2℃的恒温箱内,电容器施加最大允许
纹波电流,施加直流电压和交流电压的峰值的
和要等于额定电压,时间 5000 小时,试验结束
后,在标准状态下放置 16 小时后进行测试。
The capacitor shall be placed in a
circulating air oven at an ambient
temperature of 105±2℃。It must not be
subjected to direct radiation from heating
elements. DC voltage and the rated ripple
current shown in table shall be applied for
a period of 5000 hours. The sum of the DC
voltage and peak AC voltage must not exceed
the full rated voltage of the capacitor. It
shall be subjected to standard atmospheric
for 16 hours, after which measurement shall
be made.
温度 Temp :105±2℃
时间 Time :1000+36 小时
电压处理:在常温下电容器串联保护电阻(1K
Ω)
,加额定电压 30 分钟,放电,常温放置 2448 小时后测量。
Condition: The DC rated voltage shall be
applied across the capacitor and its
protective resistor (1KΩ) for 30 minutes,
The capacitor shall then be stored under
standard atmospheric conditions for 24 - 48
hours.
浸渍时间 Solder press time: 2±0.5s
焊接温度
Solder temperature:
245±5℃
浸渍速度
Speed of immersion
3±2.5mm/sec
浸渍时间和温度 Solder temperature/immersion:
260±5℃持续 10±1 s 或者 350±10℃持续 3.5
±0.5s
260±5℃ for 10±1s or 350±10℃ for 3.5±
0.5s .
9.8
高温存储
Shelf life
9.9
可焊性
Solder
ability
9.10
耐焊接热
Resistance
to soldering
heat
9.11
耐湿性
Resistance
of
dump
heat
Conditions
温度: 40±2℃
Test Temperature :
40±2℃
湿度:90-95% RH
Relative Humidity:
90-95%RH
时间:240±8hrs
试验后常温放置 24-48 小时
To expose in the atmospheric condition for 24 to
48 hours after completion of test
南通江海电容器股份有限公司
技术要求 Specifications
漏电流:不超过规定值
容量变化:初测值的±20 % 以内
损耗角正切:不超过规定值的 2 倍
Leakage current : ≤
Initial specified value
Capacitance change:
Within ±20 % of initial value
dissipation factor : ≤
200% of initial specified value
外观 Appearance :无明显异常
No remarkable abnormality
漏电流:不超过规定值
容量变化:初测值的±15 % 以内
损耗角正切:不超过规定值的 1.5 倍
Leakage current : ≤
Initial specified value
Capacitance change:
Within ±15% of initial value
dissipation factor : ≤
150% of initial specified value
外观 Appearance :无明显异常
No remarkable abnormality
浸渍面积 95%以上附着
At least 95% of
Circumferential surface of the dipped portion
of termination shall be covered with new
solder
漏电流:不超过规定值
Leakage Current: Not more than the specified
value
电容量变化:初测值的±10%以内
Capacitance
Change :within±10% of the initial value
损耗角正切;不超过规定值
Dissipation factor: Not more than the
specified value
外观 Appearance :无明显异常
No remarkable abnormality
漏电流:不超过规定值
Leakage Current: Not more than the specified
value
电容量变化:
i. V>160v 初测值的±10%以内
ii. V≤160v 初测值的±15%以内
Capacitance change:
i. V>160v within ±10% of the initial value
ii. V ≤ 160v within ± 15% of the initial
value
损耗角正切:不超过规定值
Dissipation factor: Not more than the
specified value
外观:无明显异常
Appearance: No remarkable abnormality
-9-
No.
9.12
项目 Items
耐振性
Resistance
vibration
条件 Conditions
to
频率:10-55-10 Hz/分
Frequency: From 10 to 55 Hz and
return to 10 Hz, shall be transferred in
1 Min
Total Amplitude: 1.5 mm
条件:X. Y. Z 方向各 2 小时
Direction and duration of vibration: 3
orthogonal directions mutually each for
2 hours Total 6 hours.
9.13
耐溶剂性
Resisting Solvent
溶剂:异丙醇
Solvent :Isopropyl alcohol
温度:20-25℃
Temperature: 20-25℃
时间:30±5s
Time : 30±5s
9.14
端子强度
Terminal
Strength
线径
Diameter
terminal
(mm)
拉伸度
Tensile
test
intensity
of
0.3
ECS2GBB221MLA220050 价格&库存
很抱歉,暂时无法提供与“ECS2GBB221MLA220050”相匹配的价格&库存,您可以联系我们找货
免费人工找货