SF104

Ｒ S F101 THRU SF106 SUPER FAST RECTIFIER Reverse Voltage: 50 to 400 Volts Forward Current:1.0Ampere S ILICON RECTIFIER １．０（２５．４） ＭＩＮ ０．１０７（２．７） ０．０８０（２．０） ＤＩＡ ０．２０５（５．２０） ０．１８０（４．１０） １．０（２５．４） ＭＩＮ ０．０３４（０．８５） ０．０２８（０．７１） ＤＩＡ SEMICONDUCTOR FEATURES Low forward voltage drop High current capability High reliability High surge current capability Super fast recovery time Good for use in switching mode circuits Plastic package has Underwriters Laboratory Flammability Classification 94V-0 DO-41 JF MECHANICAL DATA Case: JEDEC DO-41 molded plastic body Terminals: Plated axial leads, solderable per MIL-STD-750,method 2026 Polarity: Color band denotes cathode end Mounting Position: Any Weight: 0.012ounce, 0.34 gram MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS (Rating at 25 C ambient temperature unless otherwise specified ,Single phase ,half wave ,60HZ,resistive or inductive load. For capacitive load,derate current by 20%.) SF 101 50 35 50 SF 102 100 70 100 SF 103 150 105 150 1.0 30.0 0.95 5.0 SF 104 200 140 200 SF 105 300 210 300 Dimensions in inches and (millimeters) Symbols Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current 0.375"(9.5mm)lead Length at Ta=55 C Peak Forward Surge Current 8.3ms single half sine-wave superimposed on rated load (JEDEC method) Maximum Instantaneous Forward Voltage at 1.0 A Maximum DC Reverse Current At Rated DC Blocking Voltage TA=25 C TA=100 C SF 106 400 280 400 Units VRRM VRMS VDC I(AV) IFSM VF IR Volts Volts Volts Amp Amps 1.25 Volts A 50 Maximum Reverse Recovery Time(Note1) Typical Junction Capacitance(Note2) Operating Junction and Storage Temperature Range Trr CJ TJ TSTG 35 50 -65 to+125 -65 to+150 25 ns PF C Note: 1.Test conditions: IF=0.5A,IR=1.0A,IRR=0.25A. 2.Measured at 1MHZ and applied reverse voltage of 4.0 Volts. 8-2 JINAN JINGHENG CO., LTD. ＮＯ．５１　ＨＥＰＩＮＧ　ＲＯＡＤ　ＰＲ　ＣＨＩＮＡ　　　ＴＥＬ：８６－５３１－６９４３６５７　　ＦＡＸ：８６－５３１－６９４７０９６　　 WWW.JIFUSEMICON.COM R ATINGS AND CHARACTERISTIC CURVES SF101 THRU SF106 FIG.1-TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC 10 NON INDUCTIVE FIG.2-TYPICAL FORWARD CURRENT DERATING CURVE AVERAGE FORWARD CURRENT (A) １．５ Single Phase Half Wave 60hz Resistive or Inductive Load 0.375"(9.5mm) Lead Length 50 NON INDUCTIVE ＋０．５Ａ Ｔｒｒ （＋） 50Vdc (APPROX) （－） D.U.T. PULSE GENERATOR (NOTE2) OSCILLOSCOPE (NOTE1) ０ －０．２５Ａ １．０ 1 NON INDUCTIVE ０．５ NOTES:1.Rise Time=7ns max. input impedance=1 megohm 22pF 2.Rise Time=10ns max. source impedance =50 ohms －１．０Ａ １ｃｍ ０ SET TIME BASE FOR 5/10 ns/cm ０ ２５ ５０ ７５ １００ １２５ １５０ １７５ AMBIENT TEMPERATURE ( C) FIG.3-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS INSTANTANEOUS FORWARD CURRENT( AMPERES) FIG.4-TYPICAL REVERSE CHARACTERISTICS INSTANTANEOUS REVERSE CURRENT ,(mA) 　１００ １００ 　１０ SF101-SF105 １０ TJ=100 C １．０ １ SF106 ０．１ TJ=25 C ０．１ TA=25 C Pulse Width=300 s 1% Duty Cycle ０．０１ ０．０１ ０ ０．２ ０．４ ０．６ ０．８ １．０ １．２ １．４ ０ ２０ ４０ ６０ ８０ １００ １２０ １４０ PERCENT OF RATED PEAK REVERSE VOLT AGE(%) INSTANTANEOUS FORWARD V OLTAGE (VOL TS) FIG.5-MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT ３５ TA=25 C 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) FIG.6-TYPICAL JUNCTION CAPACITANCE １７５ JUNCTION CAPACITANCE(pF) ３０ １５０ １２５ １００ ７５ ５０ ２５ １ ０．１ ０．５ １ ２ ５ １０ ２０ ５０ １００ ２００ ５００ １０００ SF106 PEAK FORWARD SURGE CURRENT(AMPERES) ２５ ２０ １５ １０ ５ ０ １ ５ １０ SF101-SF105 TJ=25 C ５０ １００ NUMBER OF CYCLES AT 60Hz REVERSE VOLTAGE. (V) 8-3 JINAN JINGHENG CO., LTD. ＮＯ．５１　ＨＥＰＩＮＧ　ＲＯＡＤ　ＰＲ　ＣＨＩＮＡ　　　ＴＥＬ：８６－５３１－６９４３６５７　　ＦＡＸ：８６－５３１－６９４７０９６　　 WWW.JIFUSEMICON.COM S ILICON RECTIFIER