160R18W225KV4E

Tanceram Chip Capacitors ® TANCERAM® chip capacitors can replace tantalum capacitors in many applications and offer several key advantages over traditional tantalums. Because TANCERAM® capacitors exhibit extremely low ESR, equivalent circuit performance can often be achieved using considerably lower capacitance values. Low DC leakage reduces current drain, extending the battery life of portable products. TANCERAM® high DC breakdown voltage ratings offer improved reliability and eliminate large voltage de-rating common when designing with tantalums. Advantages • Low ESR • Low DC Leakage • Higher Surge Voltage • Non-polarized Devices • Reduced CHIP Size • Improved Reliability • Higher Insulation Resistance • Higher Ripple Current Applications • Switching Power Supply Smoothing (Input/Output) • Backlighting Inverters • DC/DC Converter Smoothing (Input/Output) • General Digital Circuits How to Order TANCERAM® 18 Part number written: 100R15X106MV4E 100 R15 X 106 M V 4 E VOLTAGE SIZE DIELECTRIC CAPACITANCE TOLERANCE TERMINATION MARKING PACKING 6R3 = 6.3 V 100 = 10 V 160 = 16 V 250 = 25 V 500 = 50 V 101 = 100 V See Chart W = X7R X = X5R 1st two digits are significant; third digit denotes number of zeros. 105 = 1.00 µF 476 = 47.0 µF 107 = 100 µF K = ±10% M = ±20% V = Nickel Barrier with 100% Tin Plating (Matte) 4 = Unmarked Code Type Reel E Plastic 7” T Paper 7” Tape specifications conform to EIA RS481 T = SnPb* (*available on select parts) www.johanson dielectrics.com DIELECTRIC Tanceram Chip Capacitors ® W W (X7R) T X (X5R) Case Size EIA / JDI L E/B Capacitance Selection INCHES (mm) VDC 1.0 µF 2.2 µF 3.3 µF 4.7 µF 10 µF 22 µF 47 µF 100 µF 105 225 335 475 106 226 476 107 16 10 0402 R07 L W T EB .040 ±.004 .020 ±.004 .025 Max. .008 ±.004 (1.02 ±.10) (0.51 ±.10) (0.64) (0.20±.10) 0603 R14 L W T EB .063 ±.008 .032 ±.008 .035 Max. .010±.005 (1.60 ±.20) (0.81 ±.20) (0.89) (.25±.13) 0805 R15 L W T EB .080 ±.010 .050 ±.010 .060 Max. .020±.010 (2.03 ±.25) (1.27 ±.25) (1.52) (0.51±.25 ) 1206 R18 L W T EB .125 ±.013 .062 ±.010 .070 Max. .020 +.015-0.01 (3.17 ±.35) (1.57 ±.25) (1.78) (0.51+.38-.25) 1210 S41 L W T EB .126 ±.016 .098 ±.012 .110 Max. .020 +.015-.010 (3.20 ±.40) (2.50 ±.30) (2.8) (0.51+.38-.25) 1812 S43 L W T EB .177 ±.016 .126 ±.015 .140 Max. .035 ±.020 (4.50 ±.40) (3.20 ±.38) (3.55) (0.89 ±0.51) 6.3   25 16 10 6.3 50 25 16 10 6.3 50 35 25 16 10 6.3 100 50 35 25 16 10 6.3 100 50 25 W X W X W X W X “K” OR “M” TOLERANCE W X W X W X W X ONLY “M” TOLERANCE Electrical Characteristics DIELECTRIC: X7R TEMPERATURE COEFFICIENT: DISSIPATION FACTOR: INSULATION RESISTANCE (MIN. @ 25°C, WVDC) DIELECTRIC STRENGTH: TEST CONDITIONS: OTHER: X5R ±15% (-55 to +125°C) ±15% (-55 to +85°C) For ≥ 50 VDC: 5% max. For ≤ 35 VDC: 10% max. For ≥ 50 VDC: 5% max. For ≤ 35 VDC: 10% max. 100 ΩF or 10 GΩ, whichever is less 2.5 X WVDC, 25°C, 50mA max. Capacitance values ≤ 10 µF: 1.0kHz±50Hz @ 1.0±0.2 Vrms Capacitance values > 10 µF: 120Hz±10Hz @ 0.5V±0.1 Vrms See page 79 for additional dielectric specifications. www.johanson dielectrics.com 19