KIA317PI

SEMICONDUCTOR TECHNICAL DATA 3-TERMINAL 1A POSITIVE ADJUSTABLE REGULATOR KIA317F/FP/PI/S BIPOLAR LINEAR INTEGRATED CIRCUIT The KIA317F/FP/PI/S is adjustable 3-terminal positive voltage regulator capable of supplying in excess of 1.5A over a 1.25V to 37V output range. This is exceptionally easy to use and require only two external resistors to set the output voltage. Further, both line and load regulation are better than standard fixed regulators. FEATURES ・Adjustable output between 1.25V and 37V ・Guaranteed 1.5A output current ・Line regulation typically 0.001%/V ・Load regulation typically 0.1% ・80dB ripple rejection (with Cadj) ・Internal thermal overload protection ・Internal short-circuit current limiting ・Output transistor safe-area compensation MAXIMUM RATINGS (Ta=25℃) CHARACTERISTIC Input-Output Voltage Differential Output Current F Power Dissipation (No Heatsink) FP PI S (Note) Operating Temperature Storage Temperature Lead Temperature mounting pad for the GND Lead min. 6㎠. Topr Tstg Tlead PD SYMBOL VIN IOUT RATING 40 1.5 1.3 2.0 W 2.0 1.0 -30～85 -65～150 230 ℃ ℃ ℃ UNIT V A Note) : Package Mounted on FR-4 PCB 36×18×1.5㎜. BLOCK DIAGRAM VIN I2 + Voltage Reference Protection Circuitry I3 I1 Adj VO 2005. 6. 24 Revision No : 4 1/6 KIA317F/FP/PI/S ELECTRICAL CHARACTERISTICS (Ta=25℃) (VI-VO=5V, IO=0.5A, 0℃≤Tj≤125℃, IMAX=1.5A, unless otherwise specified.) CHARACTERISTIC SYMBOL ΔVO(Line) TEST CONDITION Ta=25℃, Io=10mA Ta=0～125℃, Io=10mA Ta=25℃, Ta=0～125℃, 3V≤Vin-Vout≤40V 10mA≤Iout≤IMAX 10mA≤Io≤IMAX, 3V≤Vin-Vout≤40V 10mA≤Io≤IMAX, 3V≤Vin-Vout≤40V, P≤PMAX TMin≤Tj≤TMAX (Vin-Vout)=40V (Vin-Vout)≤15V, P≤PMAX (Vin-Vout)≤40V, P≤PMAX, Ta=25℃ Ta=25℃, 10HZ≤f≤10kHZ, % of Vout Vo=10V, f=120HZ CAdj=10㎌ Ta=25℃ for end point measurement, 1000 Hr 1.20 1.5 0.15 66 0.02 0.1 0.3 50 0.2 1.25 1 3.5 2.2 0.4 0.0003 65 80 0.3 0.07 0.5 % 1.5 100 5 1.30 10 3.4 dB 1 % ㎂ ㎂ V % mA A A % MIN. TYP. 0.01 MAX. 0.04 %/V UNIT Line Regulation Load Regulation Adjustable Pin Current Adjustable Pin Current Change Reference Voltage Temperature Stability Minimum Load Current to Maintain Regulation Current Limit Output Noise Voltage Ripple Rejection Ratio Long Term Stability ΔVO(Load) IAdj ΔIAdj Vref STT Io(MIN) Io(MAX) VNO RR ST Note : Load and line regulation are specified at constant junction temperature. Change in Vo due to heating effects must be taken into account separately. Pulse testing with low duty is used. TYPICAL APPLICATION (PROGRAMMABLE REGULATOR) V IN V IN Adj I Adj Ci 0.1µF R2 VO R1 CO 1µF V OUT = 1.25V (1 + R2 ) + I Adj R 2 R1 Ci is required when regulator is located an appreciable distance from power supply filter. Co is not needed for stability, however, in the range of 1㎌ to 100㎌ of aluminum or tantalum electrolytic are commonly used to provide improved output impedance and rejection of transients. Since IAdj is controlled to less then 100㎂, the error associated with this term is negligible in most applications. 2005. 6. 24 Revision No : 4 2/6 KIA317F/FP/PI/S Load Regulation OUTPUT VOLTAGE DEVIATION (%) 0.2 0 -0.2 IL = 1.5A IL = 0.5A Current Limit 3 OUTPUT CURRENT (A) 2 -0.4 -0.6 -0.8 -1.0 -75 1 Tj = 150 C Tj = -55 C VIN =15V VOUT =10V Tj = 25 C 0 0 25 50 75 100 125 150 -50 -25 0 10 20 30 40 TEMPERATURE ( C) INPUT-OUTPUT DIFFERENTIAL (V) Adjustment Current ADJUSTMENT CURRENT (µA) 60 55 50 45 40 35 -75 -50 -25 0 25 50 75 100 125 150 Dropout Voltage INPUT-OUTPUT DIFFERENTIAL (V) 3.0 VOUT =100mV 2.5 IL = 1.5A IL = 1A 2.0 IL = 500mA 1.5 IL = 200mA IL = 20mA 1.0 -75 -50 -25 0 25 50 75 100 125 150 TEMPERATURE ( C) TEMPERATURE ( C) Temperature Stability 1.260 4.5 Minimum Operating Current QUIESCENT CURRENT (mA) REFERENCE VOLTAGE (V) 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 0 10 20 30 40 T j =25 C T j =150 C T j =-55 C 1.250 1.240 1.230 1.220 -75 -50 -25 0 25 50 75 100 125 150 TEMPERATURE ( C) INPUT-OUTPUT DIFFERENTIAL (V) 2005. 6. 24 Revision No : 4 3/6 KIA317F/FP/PI/S Ripple Rejection 100 100 CADJ =10µF Ripple Rejection VIN = 15V, VOUT = 10V IL=500mA, Tj=25 C RIPPLE REJECTION (dB) 80 CADJ =0 RIPPLE REJECTION (dB) 80 60 CADJ =10µF CADJ =0 60 40 40 20 0 20 0 0 VIN - VOUT = 5V IL=500mA, f = 120Hz Tj=25 C 5 10 15 20 25 30 35 0 100 1K 10K 100K 1M OUTPUT VOLTAGE (V) FREQUENCY (Hz) Ripple Rejection 100 80 60 40 20 VIN = 15V, VOUT = 10V f = 120Hz, Tj=25 C Output Impedance 10 1 VIN = 15V, VOUT = 10V IL=500mA, Tj=25 C OUTPUT IMPEDANCE (Ω) RIPPLE REJECTION (dB) CADJ =10µF CADJ =0 10 0 CADJ =10µF 10 -1 10 -2 CADJ =0 0 0.01 0.1 1 10 10 -3 10 100 1K 10K 100K 1M OUTPUT CURRENT (A) FREQUENCY (Hz) INPUT VOLTAGE OUTPUT VOLTAGE CHANGE (V) DEVIATION (V) LOAD CURRENT (A) OUTPUT VOLTAGE DEVIATION (V) Line Transient Response 1.5 1.0 0.5 0 -0.5 -1.0 -1.5 1.0 0.5 0 0 10 20 30 40 CL=0; CL=1µF; CADJ =0 CADJ =10µF Line Transient Response 3 2 1 0 -1 -2 -3 1.5 1.0 0.5 0 0 10 20 30 40 CL=0; CL=1µF; CADJ =0 CADJ =10µF VIN = 15V VOUT = 10V INL=50mA Tj=25 C VOUT = 10V IL=50mA Tj=25 C TIME (µs) TIME (µs) 2005. 6. 24 Revision No : 4 4/6 KIA317F/FP/PI/S Power Dissipation-2 (DPAK) 15 40 Power Dissipation-3 (D2PAK) POWER DISSIPATION PD (W) THERMAL RESISTANCE J-A J-C C/W 62.5 3.6 POWER DISSIPATION PD (W) 12 9 6 3 0 0 50 THERMAL RESISTANCE J-A J-C C/W 9.62 96.2 35 30 25 20 15 10 5 0 -25 0 25 50 75 100 150 100 125 150 AMBIENT TEMPERATURE Ta ( C) AMBIENT TEMPERATURE Ta ( C) Power Dissipation-1 (TO-220IS) 24 Power Dissipation-4 (SOT-223) 12 POWER DISSIPATION PD (W) 20 16 12 8 4 0 -25 POWER DISSIPATION PD (W) THERMAL RESISTANCE J-C J-A C/W 6.0 62.5 10 8 6 4 2 0 -25 THERMAL RESISTANCE J-A J-C C/W 15 125 0 50 100 150 0 50 100 150 AMBIENT TEMPERATURE Ta ( C) AMBIENT TEMPERATURE Ta ( C) 2005. 6. 24 Revision No : 4 5/6 KIA317F/FP/PI/S A C D I J A I J H F 1 2 F 3 P L DIM A B C D E F H I J K L M O P Q MILLIMETERS _ 6.60 + 0.2 _ 6.10 + 0.2 _ 5.0 + 0.2 _ 1.10 + 0.2 _ 2.70 + 0.2 _ 2.30 + 0.1 1.00 MAX _ 2.30 + 0.2 _ 0.5 + 0.1 _ 2.00 + 0.20 _ 0.50 + 0.10 _ 0.91+ 0.10 _ 0.90 + 0.1 _ 1.00 + 0.10 0.95 MAX DIM A B B N R E G F M O C D E F G I J K L M N O KQ Q R D K 1 2 3 P E L C MILLIMETERS _ 9.8 + 0.2 _ 8.8 + 0.2 8.0 _ 15 + 0.3 _ 5.0 + 0.2 _ 2.54 + 0.1 _ 0.8 + 0.1 _ 4.0 + 0.2 _ 1.27 + 0.13 6.7 _ 0.5 + 0.15 0~0.25 _ 1.27 + 0.1 _ 2.3 + 0.3 7.85 0~0.15 B M Q 1. ADJ 2. OUTPUT 3. INPUT 1. ADJ 2. OUTPUT 3. INPUT O DPAK D2 PAK A U E G B F A C H L L K L M D D J N T N T Q 1 2 3 DIM A B C S D E F G RH T J K L M V N O P Q R H S T U 1. ADJ V 2. OUTPUT 3. INPUT O MILLIMETERS 10.30 MAX 15.30 MAX 2.70±0.30 0.85 MAX Φ3.20±0.20 3.00±0.30 12.30 MAX 0.75 MAX 13.60±0.50 3.90 MAX 1.20 1.30 2.54 4.50±0.20 6.80 2.60±0.20 10° 25° 5° 0.5 2.60±0.15 P E B K J G F F DIM A B C MILLIMETERS _ 6.5 + 0.2 _ 3.5 + 0.2 1.8 MAX 0.7+0.15/-0.1 _ 7 + 0.3 2.3 TYP 0.26+0.09/-0.02 3.0+0.15/-0.1 _ 1.75 + 0.25 0.1 MAX 10 MAX 1 2 3 C D E D F G H J K L 1. ADJ 2. OUTPUT 3. INPUT TO-220IS SOT-223 2005. 6. 24 Revision No : 4 6/6