Product Bulletin
Surface Mount Ceramic Chip Capacitors – C0402 Series - C0G Dielectric
Outline Drawing
W T S ELECTRODES L B NICKEL PLATE CONDUCTIVE METALLIZATION TIN PLATE
Dimensions – Millimeters (Inches)
EIA Size Metric Size Code Code 0402 1005 L L ength 1.0 (.039) ± 0.05 (.002) W Width 0.5 (.020) ± 0.05 (.002) B Bandwidth 0.25 (.010) ± 0.10 (.004) S Separation -
See Capacitance Value Table below for thickness dimension.
Capacitance Value
Capacitance Value (pF) 120 150 180 220 270 330 KEMET Part Number C0402C121J5GAC C0402C151J5GAC C0402C181J5GAC C0402C221J5GAC C0402C271J5GAC C0402C331J5GAC Voltage 50 50 50 50 50 50 Capacitance Tolerance ±5% ±5% ±5% ±5% ±5% ±5% Thickness 0.5 (.020) ± 0.05 (.002) 0.5 (.020) ± 0.05 (.002) 0.5 (.020) ± 0.05 (.002) 0.5 (.020) ± 0.05 (.002) 0.5 (.020) ± 0.05 (.002) 0.5 (.020) ± 0.05 (.002) Qty 7" Reel 10,000 10,000 10,000 10,000 10,000 10,000 Qty 13" Reel 50,000 50,000 50,000 50,000 50,000 50,000
F-9080A 03/06
Capacitor Ordering Information
C 0402
Style C - Ceramic Size Code See dimension table Specification C - Standard
C
331
J
5
G
A
C
End Metallization C = Standard (Tin-plate nickel barrier) Failure Rate Level A = Not Applicable
Capacitance Code, pF First two digits represent significant figures. Third digit specifies number of zeros. 100 pF = 101. (Use “9” for 1.0 through 9.9 pF) (Use “8” for 0.1 through .99 pF) Capacitance Tolerance J = ± 5%
Temperature Characteristic Designated by Capacitance Change Over Temperature Range G = C0G (0±30 ppm/°C) (-55°C +125°C) Voltage 5 = 50V
Electrical Parameters As detailed in the KEMET Surface Mount Catalog F3102 for C0G, with following specific requirements based on room temperature (25°C) parameters: • Operating Range: -55°C to +125°C, with no-bias capacitance shift limited to ± 30 ppm/°C over that range. • Insulation Resistance (IR) measured after 2 minutes at rated voltage @ 25°C: Limit is 10,000 MΩ, minimum. • Capacitance and Quality Factor (Q) measured at 1 MHz and 0.5 Vrms: DF limit is 0.1% Q = (< 30 pF: Q ≥ 400 + 20C; > 30pF: Q ≥ 1000) C = Nominal Capacitance Soldering Process These components are suitable for reflow only. All parts incorporate the standard KEMET barrier layer of pure nickel, with an overplate of pure tin to provide excellent solderability as well as resistance to leaching. Marking These chips will be supplied unmarked. In general, the information in the KEMET Surface Mount catalog F3102 applies to these capacitors. The information in this bulletin supplements that in the catalog.
F-9080A 03/06
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
很抱歉,暂时无法提供与“C0402C221J5GAC”相匹配的价格&库存,您可以联系我们找货
免费人工找货