C0603C473M1RAC

Product Bulletin Surface Mount Ceramic Chip Capacitors – 100 Volt Series – X7R Dielectric Outline Drawing W T S ELECTRODES L B NICKEL PLATE CONDUCTIVE METALLIZATION TIN PLATE Dimensions – Millimeters (Inches) EIA Size Code 0603 0805 1206 1210 Metric Size Code 1608 2012 3216 3225 L Length 1.6 (.063) ± 0.15 (.006) 2.0 (.079) ± 0.2 (.008) 3.2 (.126) ± 0.2 (.008) 3.2 (.126) ± 0.2 (.006) W Width 0.8 (.031) ± 0.15 (.006) 1.25 (.049) ± 0.2 (.008) 1.6 (.063) ± 0.2 (.008) 2.5 (.098) ± 0.2 (.008) B Bandwidth 0.35 (.014) ± 0.15 (.006) 0.5 (.02) ± 0.25 (.010) 0.5 (.02) ± 0.25 (.010) 0.5 (.02) ± 0.25 (.010) S Separation 0.7 (.028) 0.75 (.030) N/A N/A See below for thickness dimension. Capacitance Value Capacitance Values (μF) 0.047 0.22 0.47 0.47 1.0 KEMET Part Number C0603C473_1RAC C0805C224_1RAC C1206C474_1RAC C1210C474_1RAC C1210C105_1RAC Voltage 100 100 100 100 100 Capacitance Tolerance J,K,M J,K,M J,K,M J,K,M J,K,M Thickness mm 0.8 (.031) ± 0.07 (.003) 1.25 (.049) ± 0.15 (.001) 1.60 (.063) ± 0.15 (.001) 0.95 (.037) ± 0.10 (.004) 1.70 (.067) ± 0.20 (.008) Qty 7” Reel 4,000 2,500 2,000 4,000 2,000 Qty 13” Reel 10,000 10,000 8,000 10,000 8,000 F-9122B 9/06 © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com Product Bulletin Electrical Parameters As detailed in the KEMET Surface Mount Catalog F3102 for X7R, with following specific requirements based on room temperature (25°C) parameters: • Operating Range: -55°C to +125°C, with no-bias capacitance shift limited to ± 15% over that range. • Insulation Resistance (IR) measured after 2 minutes at rated voltage @ 25°C: Limit is 500 megohm microfarads or 50,000MΩ, whichever of the two is smaller. • Capacitance and Dissipation Factor (DF) measured at the following conditions: DF Limit is 2.5%. 1 kHz and 1 Vrms. Qualifications/ Certifications • AEC-Q200 Rev. C • RoHS Compliant Soldering Process These components are suitable for reflow and wave soldering. All parts incorporate the standard KEMET barrier layer of pure nickel, with an overplate of pure tin to provide excellent solderability as well as resistance to leaching. Marking These chips will be supplied unmarked. If required, they can be laser-marked as an extra option. Details on the marking format are included in KEMET Surface Mount catalog F3102. enville, SC 29606 (864) 963-6300 • www.k In general, the information in the KEMET Surface Mount catalog F3102 applies to these capacitors. The information in this bulletin supplements that in the catalog. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com