C0805C684K5RAC

Product Bulletin Surface Mount Ceramic Chip Capacitors – X7R Dielectric - Capacitance Extensions Outline Drawing W T S ELECTRODES L B NICKEL PLATE CONDUCTIVE METALLIZATION TIN PLATE Dimensions – Millimeters (Inches) EIA Size Metric Size Code Code 0402 0603 0805 1206 1210 1005 1608 2012 3216 3225 L Length 1.0 (.039) ± 0.05 (.002) 1.6 (.063) ± 0.15 (.006) 2.0 (.079) ± 0.02 (.008) 3.2 (1.26) ± 0.2 (.008) 3.2 (.126) ± 0.2 (.008) W Width 0.5 (.020) ± 0.05 (.002) 0.8 (.032) ± 0.15 (.006) 1.25 (.049) ± 0.2 (.008) 1.6 (.063) ± 0.2 (.008) 2.5 (.098) ± 0.2 (.008) B Bandwidth 0.20 (.008) ± 0.4 (.016) 0.35 (.014) ± 0.15 (.006) 0.5 (.020) ± 0.25 (.010) 0.5 (.020) ± 0.25 (.010) 0.5 (.020) ± 0.25 (.010) S Seperation 0.3 (.012) 0.7 (.028) 0.75 (.030) - See Capacitance Value Table below for thickness dimension. Capacitor Ordering Information C 0603 Style C - Ceramic Size Code See dimension table Specification C - Standard C 105 K 4 R A C End Metallization C = Standard (Tin-plate nickel barrier) Failure Rate Level A = Not Applicable Capacitance Code, pF First two digits represent significant figures. Third digit specifies number of zeros. 100 pF = 101. (Use “9” for 1.0 through 9.9 pF) (Use “8” for 0.1 through .99 pF) Capacitance Tolerance K = ± 10% M = ±20% Temperature Characteristic Designated by Capacitance Change Over Temperature Range R = X7R (±15%) (-55°C +125°C) 9 = 6.3V 3 = 25V 8 = 10V 5 = 50V Voltage 4 = 16V F-9079B 9/06 Capacitance Value Capacitance Value ( µF) 0.022 0.022 0.047 0.15 0.22 1 0.47 0.68 1 2.2 2.2 4.7 10 10 10 2.2 3.3 4.7 4.7 4.7 4.7 KEMET Part Number C0402C223_3RAC C0402C223_5RAC C0402C473_3RAC C0603C154_5RAC C0603C224_3RAC C0805C105_3RAC C0805C474_5RAC C0805C684_5RAC C1206C105_5RAC C1206C225_3RAC C1206C225_5RAC C1206C475_3RAC C1210C106_4RAC C1210C106_8RAC C1210C106_9RAC C1210C225_5RAC C1210C335_5RAC C1210C475_3RAC C1210C475_4RAC C1210C475_8RAC C1210C475_9RAC Voltage 25 50 25 50 25 25 50 50 50 25 50 25 16 10 6.3 50 50 25 16 10 6.3 Capacitance Tolerance K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M K, M Thickness 0.5 (.020) ± 0.05 (.002) 0.5 (.020) ± 0.05 (.002) 0.5 (.020) ± 0.05 (.002) 0.8 (.032) ± 0.15 (.006) 0.8 (.032) ± 0.15 (.006) 1.25 (.049) ± 0.20 (.008) 1.00 (.040) ± 0.10 (.004) 1.25 (.049) ± 0.20 (.008) 1.00 (.040) ± 0.10 (.004) 1.20 (.047) ± 0.15 (.006) 1.60 (.063) ± 0.20 (.008) 1.60 (.063) ± 0.20 (.008) 1.55 (.061) ± 0.15 (.006) 1.55 (.061) ± 0.15 (.006) 1.55 (.061) ± 0.15 (.006) 1.25 (.049) ± 0.15 (.006) 1.70 (.067) ± 0.20 (.008) 1.25 (.049) ± 0.15 (.006) 0.90 (.035) ± 0.10 (.004) 0.90 (.035) ± 0.10 (.004) 0.90 (.035) ± 0.10 (.004) Qty 7" Reel 10,000 10,000 10,000 4,000 4,000 3,000 2,500 3,000 2,500 2,500 2,000 2,000 2,000 2,000 2,000 2,500 2,000 2,500 4,000 4,000 4,000 Qty 13" Reel 50,000 50,000 50,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 8,000 8,000 8,000 8,000 8,000 10,000 8,000 10,000 10,000 10,000 10,000 Electrical Parameters As detailed in the KEMET Surface Mount Catalog F3102 for X7R, with the following specific requirements based on room temperature (25°C) parameters: • Operating Range: -55°C to +125°C, with no-bias capacitance shift limited to the ± 15% over that range. • Insulating Resistance (IR) measured after 2 minutes at rated voltage @25°C: Limit is 500 megohmmicrofarads or 10,000MΩ , whichever of the two is smaller. • Capacitance and Dissipation Factor (DF) are measured under the following conditions: 1kHz and 1 Vrms if capacitance * 10µF 120Hz and 0.5 Vrms if capacitance $ 10µF • DF limits: 50 -200 Volts ü 2.5% 16 -25 Volts ü 3.5% 6.3 / 10 Volts ü 5.0% Soldering Process All parts incorporate the standard KEMET barrier layer of pure nickel, with an ove rplate of pure tin to provide excellent solderability as well as resistance to leaching. The recommended mounting techniques are as follows: • 0402 / 1210 case sizes ü Solder Reflow • 0603 / 0805 / 1206 case sizes ü Solder Wave / Solder Reflow Marking These chips will be supplied unmarked. If required, they can be laser-marked as an extra option. Details on the marking format are included in KEMET Surface Mount catalog F3102. In general, the information provided in the KEMET Surface Mount catalog F3102 applies to these capacitors. The Information in this bulletin supplements that in the catalog F-9079B 9/06 © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com