C771U472MYWDAAWL35

Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, C700, Encapsulated, KJY Type, X1 440/400 VAC/Y2 300/250 VAC (Industrial Grade) Overview KEMET’s C700 encapsulated radial leaded ceramic disc capacitors are specifically designed for interferencesuppression AC line filtering applications. Having internationally recognized safety certifications, these capacitors are well-suited for applications that require keeping potentially disruptive or damaging line transients and EMI out of susceptible equipment. They are also an ideal solution when needing to suppress line disturbances at the source. Safety Certified Capacitors are classified as either X and/or Y capacitors. Class X capacitors are primarily used in lineto-line (across-the-line) applications. In this application, there is no danger of electric shock to humans should the capacitor fail, but could result in a risk of fire. The class Y capacitor is primarily used in line-to-ground (line by-pass) applications. In this application, failure of the capacitor could lead to danger of electric shock. With a working voltage of 440/400 VAC in line-to-line (Class X) and 300/250 VAC in line-to-ground (Class Y) applications, these safety capacitors meet the impulse test criteria outlined in IEC Standard 60384. Meeting subclass X1 and Y2 requirements, these devices are certified to withstand impulses up to 4 KV (X1) and 5 KV (Y2) respectively. These encapsulated devices also meet the flame test requirements outlined in UL Standard 94 V-0. Benefits • Safety standard recognized (IEC 60384-14) • Reliable operation up to 125°C • Class X1 440/400 VAC/Y2 300/250 VAC • 5.0 mm, 7.5 mm, 10 mm, and 12.5mm lead spacing • Lead(Pb)-free and RoHS Compliant • Halogen-free • Capacitance offerings ranging from 100 pF up to 10 nF • Available capacitance tolerances of ±5%, ±10%, and ±20% • High-reliability • Preformed (crimped) or straight lead configurations • Non-polar device, minimizing installation concerns • Encapsulation meets flammability standard UL 94 V-0 Applications Typical applications include: • Line-to-line (Class X) filtering • Line-to-ground (Class Y) filtering • Antenna coupling • Primary and secondary coupling (switching power supplies) • Line disturbances suppression (motors and motor controls, relays, switching power supplies and invertors) Built Into Tomorrow © KEMET Electronics Corporation • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com C1103_KJY • 12/1/2023 1 Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, C700, Encapsulated, KJY Type, X1 440/400 VAC/Y2 300/250 VAC (Industrial Grade) Ordering Information C7 8 1 U 103 Ceramic Series Body Diameter Lead Spacing1,2,3 Spec. C7 = Ceramic 700 0 = 7.0 mm 1 = 8.0 mm 2 = 9.0 mm 3 = 10.0 mm 4 = 11.0 mm 5 = 12.0mm 6 = 13.0 mm 7 = 14.0 mm 8 = 15.0 mm 9 = 16.0 mm 5 = 5.0 mm 7 = 7.5 mm 1 = 10.0 mm 2 = 12.5 mm U= Safety M Y V Capacitance Capacitance Code (pF) Tolerance Rated Voltage Two significant digits and Number of zeroes Y = X1 400 VAC/ Y2 250 VAC Z = X1 440 VAC/ Y2 300 VAC K = ±10% M = ±20% D A A Dielectric/ Lead Failure Design Temp. Char. Configuration1,3 Rate S = SL Y = Y5P W = Y5U V = Y5V D= Disc A = Straight B = Vertical Kink C = Outside Kink D = Inside Kink A= N/A 7301 Packaging (C-Spec) See "Packaging C-Spec Ordering Options Table" below Due to a high risk of arcing, "Inside Kink" lead configuration cannot be combined with the 5 mm lead spacing option. The "Inside Kink" option is only available on capacitors with lead spacing of 7.5 mm or greater. A potential for arcing may exist when combining the "Inside Kink" lead configuration with a 7.5 mm lead spacing option, especially in high humidity environments and/or when exposure to voltages and transients may impact creepage and clearance requirements. 2 Capacitor body diameter will limit available lead spacing and packaging options. See "Dimensions" and "Product Ordering Codes and Ratings" sections of this document to determine availability. 3 Bulk packaging lead length availability is dependent upon "Lead Configuration" and "Lead Spacing." See "Dimensions" section of this document to verify availability of a specific lead length option. For nonstandard lead length inquiries, please contact KEMET. 1 Packaging C-Spec Ordering Options Table Packaging Type Reel Ammo Pack Bulk Bag 1 2 Lead Length (mm)2,3 See Note 2 Packaging Ordering Code (C-Spec) 7301 7317 3.5 ±1.0 WL35 5.0 ±1.0 WL50 25.0 mm Minimum WL25 For nonstandard lead length inquiries, please contact KEMET. Lead length for ammo and reel pack packaging is defined by the H and H0 dimensions in Table 3. © KEMET Electronics Corporation • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com C1103_KJY • 12/1/2023 2 Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, C700, Encapsulated, KJY Type, X1 440/400 VAC/Y2 300/250 VAC (Industrial Grade) Lead Configurations Straight 1 Vertical Kink Outside Kink Inside Kink1 Due to a high risk of arcing, the "Inside Kink" lead configuration option cannot be combined with 5 mm lead spacing ("S" dimension above). The "Inside Kink" option is only available on devices with lead spacing of 7.5 mm, 10 mm, or 12.5 mm. Dimensions – Millimeters Lead Lead Configuration Configuration Ordering Code1 Straight A Vertical Kink (Preformed) B Outside Kink (Preformed) C Inside Kink (Preformed) D S Lead Spacing2 5.0 7.5 10.0 12.5 5.0 7.5 10.0 12.5 5.0 7.5 10.0 12.5 7.5 10.0 12.5 Lead Spacing Tolerance ±1.0 D T V F Body Diameter2 Body Thickness Width Lead Diameter See Table 1 - "Product Ordering Codes and Ratings" 2.1 ± 0.5 0.60 ±0.1 Lead Configuration is identified in the 13th character of the ordering code. See "Lead Configuration" and "Ordering Information" sections of this document for further details. 2 Body diameter of capacitor will limit available lead spacing and packaging options. See "Product Ordering Codes and Ratings" sections of this document for further details. 1 © KEMET Electronics Corporation • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com C1103_KJY • 12/1/2023 3 Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, C700, Encapsulated, KJY Type, X1 440/400 VAC/Y2 300/250 VAC (Industrial Grade) Approval Standard and Certification No. Safety Standard Standard No. Subclass Working Voltage TUV IEC 60384-14 X1 400 VAC Y2 250 VAC TUV IEC 60384-14 X1 440 VAC Y2 300 VAC UL CAN/CSA UL 60384-14 and E60384-14 X1 400 VAC Y2 250 VAC UL CAN/CSA UL 60384-14 and E60384-14 X1 440 VAC Y2 300 VAC Certificate No. R50466992 R50466992 E356389 E356389 These devices are TUV and UL recognized for antenna coupling and AC line-to-line (Class X) and line-to-ground (Class Y) applications per IEC60384-14 and UL 60384-14. Environmental Compliance These devices are Halogen-free and RoHS Compliant. They meet all requirements set forth by both EU and China RoHS directives. © KEMET Electronics Corporation • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com C1103_KJY • 12/1/2023 4 Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, C700, Encapsulated, KJY Type, X1 440/400 VAC/Y2 300/250 VAC (Industrial Grade) Table 1A – X1 400 Y2 250 Product Ordering Codes and Ratings Dimensions (mm) Dielectric/ Temp. Char. Y5P Y5U Y5V Dielectric/ Temp. Char. KEMET Part Number C71(1)U101KYYD(2)A(3) C71(1)U151KYYD(2)A(3) C71(1)U181KYYD(2)A(3) C71(1)U221KYYD(2)A(3) C71(1)U331KYYD(2)A(3) C71(1)U471KYYD(2)A(3) C72(1)U561KYYD(2)A(3) C72(1)U681KYYD(2)A(3) C73(1)U102KYYD(2)A(3) C71(1)U102MYWD(2)A(3) C72(1)U152MYWD(2)A(3) C73(1)U222MYWD(2)A(3) C74(1)U252MYWD(2)A(3) C75(1)U332MYWD(2)A(3) C76(1)U392MYWD(2)A(3) C77(1)U472MYWD(2)A(3) C71(1)U102MYVD(2)A(3) C71(1)U152MYVD(2)A(3) C72(1)U222MYVD(2)A(3) C73(1)U252MYVD(2)A(3) C73(1)U332MYVD(2)A(3) C74(1)U392MYVD(2)A(3) C75(1)U472MYVD(2)A(3) C76(1)U502MYVD(2)A(3) C77(1)U562MYVD(2)A(3) C78(1)U682MYVD(2)A(3) C79(1)U103MYVD(2)A(3) KEMET Part Number Capacitance Capacitance Tolerance 100 pF 150 pF 180 pF 220 pF 330 pF 470 pF 560 pF 680 pF 1000 pF 1000 pF 1500 pF 2200 pF 2500 pF 3300 pF 3900 pF 4700 pF 1000 pF 1500 pF 2200 pF 2500 pF 3300 pF 3900 pF 4700 pF 5000 pF 5600 pF 6800 pF 10000 pF Capacitance Body Diameter (Maximum) Lead Spacing Body Thickness (Maximum) Lead Diameter 5.0 0.60 ± 0.1 5 mm 7.5 mm 10.0 mm 12.5 mm Body Thickness (Maximum) Lead Diameter Lead Spacing 8.0 ±10% 9.0 ±20% 10.0 8.0 9.0 10.0 11.0 12.0 13.0 14.0 8.0 9.0 10.0 ±20% Capacitance Tolerance 11.0 12.0 13.5 14.0 15.0 16.0 Body Diameter (Maximum) (1) To properly complete ordering code, insert the one-digit numeric code to reflect required lead spacing: (Note that select capacitance values and packaging options may limit lead spacing availability. See table above to verify availability.) 5 = 5.0 mm 7 = 7.5mm 1 = 10.0 mm 2 = 12.5 mm (2) To properly complete ordering code, insert the one-digit character code to reflect the required lead configuration: (See "Lead Configuration" section of this document, page 2, for further details.) A = Straight B = Vertical Kink C = Outside Kink D = Inside Kink (3) To properly complete ordering code, enter the four-digit numeric or alphanumeric "Packaging C-Spec Ordering Code." See "Dimensions" section of this document, page 2, for available options. © KEMET Electronics Corporation • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com C1103_KJY • 12/1/2023 5 Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, C700, Encapsulated, KJY Type, X1 440/400 VAC/Y2 300/250 VAC (Industrial Grade) Table 1B – X1 440 Y2 300 Product Ordering Codes and Ratings Dimensions (mm) Dielectric/ Temp. Char. Y5P Y5U Y5V Dielectric/ Temp. Char. KEMET Part Number C71(1)U101KZYD(2)A(3) C71(1)U151KZYD(2)A(3) C71(1)U181KZYD(2)A(3) C71(1)U221KZYD(2)A(3) C71(1)U331KZYD(2)A(3) C71(1)U471KZYD(2)A(3) C72(1)U561KZYD(2)A(3) C72(1)U681KZYD(2)A(3) C73(1)U102KZYD(2)A(3) C71(1)U102MZWD(2)A(3) C72(1)U152MZWD(2)A(3) C73(1)U222MZWD(2)A(3) C74(1)U252MZWD(2)A(3) C75(1)U332MZWD(2)A(3) C76(1)U392MZWD(2)A(3) C77(1)U472MZWD(2)A(3) C71(1)U102MZVD(2)A(3) C71(1)U152MZVD(2)A(3) C72(1)U222MZVD(2)A(3) C73(1)U252MZVD(2)A(3) C73(1)U332MZVD(2)A(3) C74(1)U392MZVD(2)A(3) C75(1)U472MZVD(2)A(3) C76(1)U502MZVD(2)A(3) C77(1)U562MZVD(2)A(3) C78(1)U682MZVD(2)A(3) C79(1)U103MZVD(2)A(3) KEMET Part Number Capacitance Capacitance Tolerance 100 pF 150 pF 180 pF 220 pF 330 pF 470 pF 560 pF 680 pF 1000 pF 1000 pF 1500 pF 2200 pF 2500 pF 3300 pF 3900 pF 4700 pF 1000 pF 1500 pF 2200 pF 2500 pF 3300 pF 3900 pF 4700 pF 5000 pF 5600 pF 6800 pF 10000 pF Capacitance Body Diameter (Maximum) Lead Spacing Body Thickness (Maximum) Lead Diameter 5.0 0.60 ± 0.1 7.5 mm 10.0 mm 12.5 mm Body Thickness (Maximum) Lead Diameter Lead Spacing 8.0 ±10% 9.0 ±20% 10.0 8.0 9.0 10.0 11.0 12.0 13.0 14.0 8.0 9.0 10.0 ±20% Capacitance Tolerance 11.0 12.0 13.5 14.0 15.0 16.0 Body Diameter (Maximum) (1) To properly complete ordering code, insert the one-digit numeric code to reflect required lead spacing: (Note that select capacitance values and packaging options may limit lead spacing availability. See table above to verify availability.) 7 = 7.5mm 1 = 10.0 mm 2 = 12.5 mm (2) To properly complete ordering code, insert the one-digit character code to reflect the required lead configuration: (See "Lead Configuration" section of this document, page 2, for further details.) A = Straight B = Vertical Kink C = Outside Kink D = Inside Kink (3) To properly complete ordering code, enter the four-digit numeric or alphanumeric "Packaging C-Spec Ordering Code." See "Dimensions" section of this document, page 2, for available options. © KEMET Electronics Corporation • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com C1103_KJY • 12/1/2023 6 Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, C700, Encapsulated, KJY Type, X1 440/400 VAC/Y2 300/250 VAC (Industrial Grade) Table 2 – Performance & Reliability: Test Methods and Conditions Item Specification −55°C to +125°C Operating Temperature Range Dielectric Strength Between lead wires No failures Body Insulation No failures Insulation Resistance (IR) 10,000 MΩ minimum Capacitance Within specified tolerance Dissipation Factor (DF) or Q Test Method Temperature Characteristics Specification Y5P DF ≤ 2.5% Y5U/Y5V DF ≤ 5.0% SL Q ≥ 300 The capacitor shall not be damaged when 2,600 VAC (rms) is applied between the lead wires for 60 seconds. The terminals (leads) of the capacitor shall be connected together. A metal foil is tightly wrapped around the body of the capacitor at a distance of about 3 to 4 mm from each terminal. The capacitor is then inserted Metal about Foil into a container filled with metal balls 3 to 4 mm approximately 1 mm in diameter. 2,600 VAC Metal (rms) is applied for 60 seconds between the Balls capacitor lead wires and metal balls. (charge/discharge current ≤ 50 mA). The insulation resistance shall be measured with 500 ±50 VDC applied after 60 ±5 seconds of charging. Characteristic Frequency SL 1 MHz ±20% Y5P /Y5U/Y5V 1 MHz ±20% Voltage 5.0 Vrms Maximum The measurement at reference temperature 25°C A capacitance measurement is made at each step specified: Temperature Characteristics Temperature Characteristics Capacitance Change Y5P Within ±10% Y5U Within +22%/−56% Y5V Within +22%/−82% SL +350~1,000% Tensile Lead wire or capacitor body shall not break. Bending Lead wire or capacitor body shall not break. Terminal Strength 1 Step Temperature 1 +25 ±2°C 2 Minimum operating temperature 3 +25 ±2°C 4 Maximum operating temperature 5 +25 ±2°C Pretreatment: Capacitor is stored at 85 ±2°C for 1 hour and then placed at room condition1 for 24 ±2 hours before measurement. With the termination in its normal position, the specimen is held by its body in such a manner that the axis of the termination is vertical. A tensile force of 10 N is applied to the termination in the direction of its axis and acting in a direction away from the body of the specimen. With the termination in its normal position, the specimen is held by its body in such a manner that the axis of the termination is vertical; a mass force of 5 N is then suspended from the end of the termination. The body of the specimen is then inclined within a period of 2 to 3 seconds, through an angle of approximately 90° in the vertical plane and then resumed to its initial position over the same period of time; this operation constitutes one bend. One bend immediately followed by a second bend in the opposite direction. “Room Condition” is defined as follows: Temperature: 20 ~ 35°C/Humidity: 45 ~ 75%/Atmospheric Pressure: 86 ~ 106 kPa. © KEMET Electronics Corporation • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com C1103_KJY • 12/1/2023 7 Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, C700, Encapsulated, KJY Type, X1 440/400 VAC/Y2 300/250 VAC (Industrial Grade) Table 2 – Performance & Reliability: Test Methods and Conditions cont. Item Specification Appearance No visual defect IR 1,000 MΩ Minimum Dielectric Strength Per item 1 Soldering Effect (Non-Preheat) Thermal Screen Capacitor 1.5 to 2.0 mm Molten Solder Within ±10% Y5P, Y5U and Y5V: within ±10% SL: within ±2.5% or ±0.25 pF, whichever is larger Appearance Capacitance Biased Humidity No visual defect Temperature Characteristics Capacitance Change Y5P Within ±10% Y5U Within ±15% Y5V Within ±30% SL Within ±5% DF Y5V and Y5U: 7.5% maximum Y5P: 5% maximum Q Q ≥ 135 IR 3,000 MΩ minimum Dielectric Strength No failures Appearance No visual defect Capacitance Change Y5P, Y5U within ±20% Y5V within ±30% 3,000 MΩ minimum SL: 1,000 MΩ minimum IR High Temperature Life Dielectric Strength No failures Pretreatment: Capacitor is stored at 85°C ±2°C for 1 hour and then placed at room condition1 for 24 ±2 hours before initial measurements. Post-treatment: Capacitor is stored for 1 to 2 hours at room condition1. Steady State Humidity: Load Humidity: 90 to 95% humidity at 40°C ±2°C for 500 ±12 hours. 90 to 95% humidity at 40°C ±2°C for 500 ±12 hours with full rated voltage applied. Post-treatment: Capacitor is stored for 1 to 2 hours at room condition1. Post-treatment: Capacitor is stored for 1 to 2 hours at room condition1. Impulse Voltage: Each individual capacitor is subjected to three 5 kv impulses prior to life testing. 0.9Vp Cx tr (uF) (uS) 0.01 1.2 0.1 1.5 U PR Vp Voltage Capacitance 1 Test Method As shown in the figure below, the lead wires are immersed in molten solder up to 1.5 mm (+5/−0 mm) from the end of the epoxy meniscus (root of lead wire). Duration/Solder Temperature: 3.5 ±0.5 seconds/350°C ±10°C or 10 ±1 seconds/260°C ±5°C U PP td (uS) 46 47 0.5Vp tr td Time Capacitors are placed in a circulating air oven for a period of 1,000 hours. The air in the oven is maintained at a temperature of 125°C ±2 throughout the test. The capacitors are subjected to 170% of Rated Voltage. Each hour the voltage is increased to AC 1,000 Vrms for 0.1 seconds. “Room Condition” is defined as follows: Temperature: 20 ~ 35°C/Humidity: 45 ~ 75%/Atmospheric Pressure: 86 ~ 106 kPa. © KEMET Electronics Corporation • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com C1103_KJY • 12/1/2023 8 Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, C700, Encapsulated, KJY Type, X1 440/400 VAC/Y2 300/250 VAC (Industrial Grade) Table 2 – Performance & Reliability: Test Methods and Conditions cont. Item Specification The capacitor flame extinguishes as follows: Flame Test Cycle Time 1~4 30 seconds maximum 5 60 seconds maximum Test Method The capacitor is exposed to a flame for 15 seconds and then removed for 15 seconds. This test is repeated for 5 cycles. Capacitor Flame 76 38 127 Gas Burner 20º (Unit:mm) The capacitors are individually wrapped in at least one, but not more than two, complete layers of cheesecloth. They are then subjected to 20 discharges. The interval between successive discharges is 5 seconds. The VAC is maintained for 2 minutes after the last discharge. F S1 Tr C1 S2 Vac L1 L2 C2 L3 C3 L4 R CX Ct Vt Oscilloscope Active Flammability The cheesecloth should not ignite. C1, 2 1 μF ±10% C3 0.033 μF ±5% 10 kV L1-10 1.5 mH ±20% 16 A Rod core choke Cx Test capacitor R 100 ±2% Ω VAC V R ±5% Ct 3 μF ±5% 10 kV VR Rated Working Voltage F Fuse, Rated 10A Vt Voltage applied to C t Vx 5kV time Passive Flammability The burning time should not exceed 30 seconds. The tissue paper should not ignite. About 8mm The capacitor under test is held into a flame and in a position which best promotes burning. Each specimen is exposed to the flame once. Test Specimen 200 45º ±5mm Tissue About 10mm Thick Board Time of Exposure to Flame: 30 seconds Length of Flame: 12 ±1 mm Gas Burner Length: 35 mm minimum Inside Diameter: 0.5 ±0.1 mm Outside Diameter: 0.9 mm maximum Gas Butane Gas Purity: 95% minimum 1 “Room Condition” is defined as follows: Temperature: 20 ~ 35°C/Humidity: 45 ~ 75%/Atmospheric Pressure: 86 ~ 106 kPa. © KEMET Electronics Corporation • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com C1103_KJY • 12/1/2023 9 Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, C700, Encapsulated, KJY Type, X1 440/400 VAC/Y2 300/250 VAC (Industrial Grade) Soldering and Mounting Information Soldering: When soldering this product to a PCB/PWB, do not exceed the solder heat resistance specification of the capacitor. Subjecting this product to excessive heating could reflow the solder joint between the lead and ceramic element and/or may result in thermal shocks that can crack the ceramic element. When soldering these capacitors with a soldering iron, it should be performed under the following conditions: • Temperature of iron-tip: 400°C maximum • Soldering iron wattage: 50 W maximum • Soldering time: 3.5 seconds maximum Cleaning (ultrasonic cleaning): To perform ultrasonic cleaning, observe the following conditions: • Rinse bath capacity: output of 20 watts per liter or less • Rinsing time: 5 minute maximum • Do not vibrate the PCB/PWB directly • Excessive ultrasonic cleaning may lead to fatigue destruction of the lead wires Construction Epoxy Encapsulation (0.2 mm Minimum Thickness, Pigment = Blue/UL 94 V-0) Detailed Cross Section Lead Attach Solder (Sn97/Ag3 Sn99.3/Cu0.5) Dielectric material (BaTiO3) Electrode (Ag/Cu) Lead Attach Solder (Sn97/Ag3 Sn99.3/Cu0.7) © KEMET Electronics Corporation • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com Electrode (Ag/Cu) Lead wire Steel Cu 100% Sn Finish Layer (3-7 µm) Core Metal Barrier Layer Dielectric material (BaTiO3) C1103_KJY • 12/1/2023 10 Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, C700, Encapsulated, KJY Type, X1 440/400 VAC/Y2 300/250 VAC (Industrial Grade) Marking These capacitors shall be laser marked with KEMET's trademark, type designation, capacitor class, rated voltage, rated capacitance, and capacitance tolerance codes. In addition, all devices are marked with the recognized approval mark and a date/lot code for traceability. Marking will be supplied on one side of the encapsulated capacitor body. All marking shall be legible to allow for clear identification of the component. Marking appears in legible contrast. Illustrated below is an example of the marking format and content. KEMET Trademark Rated Capacitance (3 Numeric Characters) Type Designation (3 Characters) Capacitance Tolerance Code (1 Character) Approval Mark UL approval mark Date/Lot Code (See Table Below) Capacitor Class and Rated Voltage Date/Lot Code e.g., 9D (December 2019, Taiwan) 9 Last digit of year, e.g., 3 = 2013 D Manufacturing Month: 1-9 = Jan - Sept O = October N = November D = December Manufacturing Location Code (blank): Taiwan C: Dongguan © KEMET Electronics Corporation • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com C1103_KJY • 12/1/2023 11 Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, C700, Encapsulated, KJY Type, X1 440/400 VAC/Y2 300/250 VAC (Industrial Grade) Packaging Quantities 1 Capacitor Body Diameter (mm) Body Diameter Code1 7.0 0 8.0 1 9.0 2 10.0 3 11.0 4 12.0 5 13.0 6 14.0 7 15.0 8 16.0 9 Bulk Bag (Loose) Lead Length (WL25) Cut Lead Length (WL35, WL50, WL10) 200 pieces/bag 500 pieces/bag The "Body Diameter Code" is located in the third character position of the ordering code. This code identifies the maximum diameter of the capacitor body in millimeters. For more information regarding the ordering code, see "Ordering Information" section of this document. Lead Spacing 5 7.5 Body Diameter (mm) Pitch (Carrier Tape) Body Diameter Code Reel (7301) Ammo Pack (7317) ≤ 12.0 12.7 0-5 2,000 pieces/reel 1,000 pieces/box 12.0 < D ≤ 16.0 25.4 6-9 1,000 pieces/reel 750 pieces/box ≤ 12.0 12.7 0-5 2,000 pieces/reel 1,000 pieces/box 6-8 1,000 pieces/reel 750 pieces/box 12.0 < D ≤ 15.0 ≥ 16.0 10 12.5 ≤ 10 ≥ 11 ≤9 ≥ 10 25.4 25.4 25.4 © KEMET Electronics Corporation • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com 9 750 pieces/reel 750 pieces/box 0-3 1,000 pieces/reel 1,000 pieces/box 4-9 750 pieces/reel 750 pieces/box 0-2 1,000 pieces/reel 500 pieces/box 3-9 500 pieces/reel 500 pieces/box C1103_KJY • 12/1/2023 12 Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, C700, Encapsulated, KJY Type, X1 440/400 VAC/Y2 300/250 VAC (Industrial Grade) Figure 1 - Ammo/Reel Pack Taping Format 5 mm and 7.5 mm Lead Spacing: P2 P For All Lead Spacing: ∆S D ∆h1 e P1 Ød F T maximum Marking Side W2 L W1 W0 ℓ P0 0 ∆h2 W t2 ØD0 t1 5 mm, 7.5 mm, 10 mm and 12.5 mm Lead Spacing: P2 P ∆S D e P1 F W2 Ød L W1 W0 P0 H H0 W ØD0 ℓ Table 3 – Ammo/Reel Pack Taping Specifications Lead Spacing 5 mm Lead Style Item Lead Spacing Straight 7.5 mm Preformed1 Straight 10 mm Preformed1 Symbol Straight 12.5 mm Preformed1 Straight Preformed1 Dimensions (mm) F 5.0 ±1.0 12.7 ±1.0 25.4 ±2.0 12.7 ±1.0 7.5 ±1.0 25.4 ±2.0 12.7 ±1.0 12.7 ±1.0 25.4 ±2.0 12.5 ±1.0 25.4 ±2.0 25.4 ±2.0 12.7 ±0.3 12.7 ±0.3 Component Pitch P Sprocket Hole Pitch P0 Sprocket Hole Center to Component Center P2 6.35 ±1.5 12.7 ±1.5 6.35 ±1.5 12.7 ±1.5 6.35 ±1.5 12.7 ±1.5 6.35 ±1.5 12.7 ±1.5 12.7 ±1.5 12.7 ±1.5 Sprocket Hole Center to Lead Center P1 3.85 ±0.7 10.2 ±1.5 3.85 ±0.7 10.2 ±1.5 2.6 ±0.7 8.95 ±1.5 2.6 ±0.7 8.95 ±1.5 7.7 ±1.5 6.45 ±1.5 12.7 ±0.3 25.4 ±2.0 10.0 ±1.0 12.7 ±0.3 Body Diameter D See "Product Ordering Codes and Ratings" section of this document. Component Alignment (side/side) ∆S 0 ±2.0 Carrier Tape Width W 18.0 +1.0/−0.5 Sprocket Hole Position W1 9.0 ±0.5 Preformed (crimped) lead configurations include vertical kink, outside kink, and inside kink. See "Lead Configurations" and "Ordering Information" sections of this document for further details. 2 Also referred to as "lead length" in this document. 1 © KEMET Electronics Corporation • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com C1103_KJY • 12/1/2023 13 Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, C700, Encapsulated, KJY Type, X1 440/400 VAC/Y2 300/250 VAC (Industrial Grade) Table 3 – Ammo Pack Taping Specifications cont. Lead Spacing 5 mm Lead Style Straight 7.5 mm Preformed1 Straight 10 mm Preformed1 12.5 mm Straight Preformed1 Straight Preformed1 Item Symbol Height to Seating Plane 2 (preformed leads1) Dimensions (mm) H0 N/A 16.0 +2.0/-0 N/A 16.0 +2.0/-0 N/A 16.0 +2.0/-0 N/A 16.0 +2.0/-0 Height to SeatingPlane 2 (straight leads) H 20.0 +1.5/-1.0 N/A 20.0 +1.5/-1.0 N/A 20.0 +1.5/-1.0 N/A 20.0 +1.5/-1.0 N/A Lead Protrusion ℓ 2.0 maximum Diameter of Sprocket Hole D0 4.0 ±0.2 Lead Diameter φd 0.6 ±0.1 Carrier Tape Thickness t1 0.6 ±0.3 Total Thickness (Carrier Tape, HoldDown Tape and Lead) t2 1.5 maximum Component Alignment (front/back ) Cut Out Length ∆h1 2.0 maximum ∆h2 L 11.0 maximum Hold-Down Tape Width W0 10.0 minimum Hold-Down Tape Position W2 3.0 maximum Coating Extension on Leads (meniscus) e 3.0 maximum for straight lead; not to exceed the bend for preformed1 lead configurations. Body Thickness T 8.0 maximum Prefromed (crimped) lead configurations include vertical kink and outside kink. See "Lead Configurations" and "Ordering Information" sections of this document for further details. 2 Also referred to as "lead length" in this document. 1 Application Notes: Storage and Operating Conditions: The Insulating coating of these devices does not form an air and moisture tight seal. Avoid exposure to moisture and do not use or store these devices in a corrosive atmosphere, especially where chloride gas, sulfide gas, acid, alkali, salt or the like are present. Before cleaning, bonding or molding these devices, it is important to verify that your process does not affect product quality and performance. KEMET recommends testing and evaluating the performance of a cleaned, bonded or molded product prior to implementing and/or qualifying any of these processes. Store the capacitors where the temperature and relative humidity do not exceed 40 degrees centigrade and 70% respectively. For optimum solderability, capacitor stock should be used promptly, preferably within 6 months of receipt. Working Voltage: Application voltage (Vp-p or Vo-p) must not exceed the voltage rating of the capacitor. Irregular voltages can be generated for a transient period of time when voltage is initially applied and/or removed from a circuit. It is important to choose a capacitor with a voltage rating greater than or equal to these irregular voltages. © KEMET Electronics Corporation • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com C1103_KJY • 12/1/2023 14 Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, C700, Encapsulated, KJY Type, X1 440/400 VAC/Y2 300/250 VAC (Industrial Grade) Application Notes (cont.): Operating Temperature and Self-Generating Heat: The surface temperature of a capacitor should be kept below the upper limit of its rated operating temperature range. Be sure to take into account the heat generated by the capacitor itself. When the capacitor is used in a high-frequency current, pulse current or similar current, it may self-generate heat due to dielectric loss. Temperature rise due to self-generated heating should not exceed 20°C (while operated at an atmosphere temperature of 25°C). Handling - Vibration and Impact: Do not expose these devices or their leads to excessive shock or vibration during use. FAILURE TO FOLLOW THE ABOVE CAUTIONS MAY RESULT, WORST CASE, IN A SHORT CIRCUIT AND CAUSE FUMING OR PARTIAL DISPERSION WHEN THE PRODUCT IS USED. © KEMET Electronics Corporation • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com C1103_KJY • 12/1/2023 15 Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, C700, Encapsulated, KJY Type, X1 440/400 VAC/Y2 300/250 VAC (Industrial Grade) KEMET Electronics Corporation Sales Offices For a complete list of our global sales offices, please visit www.kemet.com/sales. Disclaimer All product specifications, statements, information and data (collectively, the “Information”) in this datasheet are subject to change. The customer is responsible for checking and verifying the extent to which the Information contained in this publication is applicable to an order at the time the order is placed. All Information given herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied. Statements of suitability for certain applications are based on KEMET Electronics Corporation’s (“KEMET”) knowledge of typical operating conditions for such applications, but are not intended to constitute – and KEMET specifically disclaims – any warranty concerning suitability for a specific customer application or use. The Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by KEMET with reference to the use of KEMET’s products is given gratis, and KEMET assumes no obligation or liability for the advice given or results obtained. Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. Although all product–related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicated or that other measures may not be required. KEMET is a registered trademark of KEMET Electronics Corporation. © KEMET Electronics Corporation • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com C1103_KJY • 12/1/2023 16