CAN17C223KARAC7800

Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) 250 VAC AC Rated Capacitors, CAN series (Industrial Grade) Overview KEMET’s CAN series are AC rated ceramic capacitors designed for 250 VAC applications where higher CV values are required but not available in safety certified MLCCs. These capacitors are qualified for continuous use under AC line conditions of 250 VAC 50/60 Hz. Available in a variety of case sizes and industry leading CV values (capacitance/voltage), these devices exhibit low leakage current and low ESR at high frequencies. For added reliability, KEMET's flexible termination technology is an available option that provides superior flex performance over standard termination systems. This series is available in X7R and C0G dielectrics. X7R exhibits a predictable change in capacitance with respect to time and voltage, and boasts a minimal change in capacitance with reference to ambient temperature. C0G exhibits no change in capacitance with respect to time and voltage and boasts a negligible change in capacitance with reference to ambient temperature. CAN series is specifically designed and tested for 50/60 Hz line frequencies and other non-safety critical applications. Benefits • Continuous AC voltage rating 250 VAC, 50/60 Hz • Offers more than 50x capacitance versus Safety Rated MLCCs • Base metal electrode (BME) dielectric system • −55°C to +125°C operating temperature range • Low ESR and ESL • Lead (Pb)-free, RoHS, and REACH Compliant • Temperature stable dielectric • Non-polar device, minimizing installation concerns • 100% pure matte tin-plated termination finish allowing for excellent solderability • Flexible termination option available upon request Click image above for interactive 3D content Open PDF in Adobe Reader for full functionality Applications • AC-DC converters • AC filtering • Power factor correction • Power supply Built Into Tomorrow © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com KEM_C1099_250_VAC_SMD • 8/10/2020 1 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) 250 VAC AC Rated Capacitors, CAN series (Industrial Grade) Ordering Information CAN Series CAN = Ceramic AC Rated MLCCs 08 C Case Size Specification/ (L"x W") Series 06 = 0603 08 = 0805 12 = 1206 13 = 1210 17 = 1808 18 = 1812 19 = 1825 21 = 2220 22 = 2225 C = Standard X = Flex 103 Capacitance Code (pF) Two single digits and number of zeros. K A R A Subclass Capacitance Rated Dielectric Designation Tolerance Voltage (V) F = ±1% G = ±2% J = ±5% K = ±10% M = ±20% A= 250 VAC 50/60 Hz R = X7R G = C0G A = N/A C TU Termination Finish Packaging (Suffix/C-Spec) C = 100% matte Sn See "Packaging C-Spec Ordering Options Table" See Table 1 for available capacitance and voltage ratings. Packaging C-Spec Ordering Options Table Packaging Type Bulk Bag1 7" Reel/Unmarked2 13" Reel/Unmarked 7" Reel/Marked2 13" Reel/Marked 1 2 Packaging/Grade Ordering Code (C-Spec) Not Required (Blank) TU 7411 (EIA 0603 case size) 7210 (EIA 0805 and larger case sizes) TM 7215 Default packaging is "Bulk Bag." An ordering code C-Spec is not required for "Bulk Bag" packaging. The terms "Marked" and "Unmarked" pertain to laser marking option of capacitors. All packaging options labeled as "Unmarked" will contain capacitors that have not been laser marked. © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com KEM_C1099_250_VAC_SMD • 8/10/2020 2 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) 250 VAC AC Rated Capacitors, CAN series (Industrial Grade) Typical Performance Capacitance Change vs. AC Voltage 15% Capacitance Change( %) 10% X7R 2220 330 nF C0G 2220 22 nF 5% 0% −5% −10% −15% −20% −25% −30% 0 25 50 75 100 125 150 175 200 225 250 Vrms at 60 Hz Electrical Parameters/Performance Characteristics Item Operating temperature range Capacitance change with reference to +25°C and 0 VDC applied (TCC) 1 Aging rate (maximum % capacitance loss/decade hour) 2 Dielectric withstanding voltage (DWV) 5 ±1 seconds and charge/discharge not exceeding 50 mA 3 4 Dissipation factor (DF) maximum limit at 25°C Insulation resistance (IR) minimum limit at 25°C 500 VDC applied for 120 ±5 seconds Dielectric Parameters/Characteristics X7R –55°C to +125°C C0G –55°C to +125°C X7R ±15% C0G ±30 ppm/°C X7R 3.0% C0G 0% X7R 945 VDC C0G 819 VDC X7R 2.5% C0G 0.1% X7R 100 MΩ-µF or 10 GΩ C0G 1,000 MΩ-µF or 100 GΩ Regarding Aging Rate: Capacitance measurements (including tolerance) are indexed to a referee time of 1,000 hours. DWV is the voltage a capacitor can withstand (survive) for a short period of time. It exceeds the nominal and continuous working voltage of the capacitor. 3 Capacitance and dissipation factor (DF) measured under the following conditions: 1 kHz ±50 Hz and 1.0 ±0.2 Vrms if capacitance ≤ 10 μF 120 Hz ±10 Hz and 0.5 ±0.1 Vrms if capacitance > 10 μF 4 To obtain IR limit, divide MΩ-μF value by the capacitance and compare to GΩ limit. Select the lower of the two limits. Note: When measuring capacitance it is important to ensure the set voltage level is held constant. The HP4284 and Agilent E4980 have a feature known as Automatic Level Control (ALC). The ALC feature should be switched to "ON". 1 2 © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com KEM_C1099_250_VAC_SMD • 8/10/2020 3 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) 250 VAC AC Rated Capacitors, CAN series (Industrial Grade) Dimensions – Millimeters (Inches) L W B T S Standard Termination Case Size EIA Size Code Metric Size Code L Length W Width 06 0603 1608 1.60 (0.063) ±0.15 (0.006) 0.80 (0.032) ±0.15 (0.006) 08 0805 2012 2.00 (0.079) ±0.20 (0.008) 1.25 (0.049) ±0.20 (0.008) 12 1206 3216 3.20 (0.126) ±0.20 (0.008) 1.60 (0.063) ±0.20 (0.008) 13 1210 3225 3.20 (0.126) ±0.20 (0.008) 2.50 (0.098) ±0.20 (0.008) 17 1808 4520 4.70 (0.185) ±0.50 (0.020) 2.00 (0.079) ±0.20 (0.008) 18 1812 4532 4.50 (0.177) ±0.30 (0.012) 3.20 (0.126) ±0.30 (0.012) 19 1825 4564 4.50 (0.177) ±0.30 (0.012) 6.40 (0.252) ±0.40 (0.016) 21 2220 5650 5.70 (0.224) ±0.40 (0.016) 5.00 (0.197) ±0.40 (0.016) 22 2225 5664 5.60 (0.220) ±0.40 (0.016) 6.40 (0.252) ±0.40 (0.016) L Length W Width 1.60 (0.063) ±0.15 (0.006) 2.00 (0.079) ±0.30 (0.012) 3.30 (0.130) ±0.40 (0.016) 0.80 (0.032) ±0.15 (0.006) 1.25 (0.049) ±0.30 (0.012) 1.60 (0.063) ±0.35 (0.013) 3.30 (0.130) ±0.40 (0.016) 2.60 (0.102) ±0.30 (0.012) 4.70 (0.185) ±0.50 (0.020) 4.50 (0.178) ±0.40 (0.016) 4.60 (0.181) ±0.40 (0.016) 5.90 (0.232) ±0.75 (0.030) 5.90 (0.232) ±0.75 (0.030) 2.00 (0.079) ±0.20 (0.008) 3.20 (0.126) ±0.30 (0.012) 6.40 (0.252) ±0.40 (0.016) 5.00 (0.197) ±0.40 (0.016) 6.40 (0.252) ±0.40 (0.016) T Thickness B Bandwidth S Separation Minimum 0.35 (0.014) ±0.15 (0.006) 0.70 (0.028) 0.75 (0.030) Mounting Technique Solder Wave or Solder Reflow 0.50 (0.02) ±0.25 (0.010) See Table 2 for Thickness N/A 0.60 (0.024) ±0.35 (0.014) Solder Reflow Only Flexible Termination Case Size EIA Size Code Metric Size Code 06 0603 1608 08 0805 2012 12 1206 3216 13 1210 3225 17 1808 4520 18 1812 4532 19 1825 4564 21 2220 5650 22 2225 5664 T Thickness B Bandwidth 0.35 (0.014) ±0.15 (0.006) 0.50 (0.02) ±0.25 (0.010) S Separation Minimum Mounting Technique 0.70 (0.028) 0.75 (0.030) Solder Wave or Solder Reflow 0.60 (0.024) ±0.25 (0.010) See Table 2 for Thickness © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com N/A 0.70 (0.028) ±0.35 (0.014) Solder Reflow Only KEM_C1099_250_VAC_SMD • 8/10/2020 4 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) 250 VAC AC Rated Capacitors, CAN series (Industrial Grade) Table 1A – X7R Dielectric Capacitance Range/Selection Waterfall Standard and Flexible Terminations Case Size/Series Cap Cap Code 1,000 pF 1,200 pF 1,500 pF 2,200 pF 2,700 pF 3,300 pF 3,900 pF 4,700 pF 5,600 pF 6,800 pF 8,200 pF 10,000 pF 12,000 pF 15,000 pF 18,000 pF 22,000 pF 27,000 pF 33,000 pF 39,000 pF 47,000 pF 56,000 pF 62,000 pF 68,000 pF 82,000 pF 0.10 µF 0.12 µF 0.15 µF 0.18 µF 0.22 µF 0.27 µF 0.33 µF 102 122 152 222 272 332 392 472 562 682 822 103 123 153 183 223 273 333 393 473 563 623 683 823 104 124 154 184 224 274 334 Cap Cap Code CAN06 0603 CAN08 0805 CAN12 1206 CAN13 1210 CAN17 1808 CAN18 1812 Voltage Code A Rated Voltage (VAC) 250 Capacitance Tolerance See Table 2 for chip thickness dimensions. F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M CG CG CG DG DG DG DG DG DG DG DG DG DG EJ EJ EJ EJ EJ EJ FZ FZ FZ FZ FU FU FK FK FK FS Rated Voltage (VAC) GB GB GB GC GE GE GE GE GH GK GN HE HE HG HJ HJ CAN21 2220 CAN22 2225 JE JE JK JL JN KE KF KH KH CAN21 2220 CAN22 2225 250 Voltage Code Case Size/Series LE LE LA LA LA LB LB LC LC LC LC CAN19 1825 A CAN06 0603 CAN08 0805 CAN12 1206 CAN13 1210 © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com CAN17 1808 CAN18 1812 CAN19 1825 KEM_C1099_250_VAC_SMD • 8/10/2020 5 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) 250 VAC AC Rated Capacitors, CAN series (Industrial Grade) Table 1B – C0G Dielectric Capacitance Range/Selection Waterfall Standard Termination Case Size/Series Cap 100 pF 110 pF 120 pF 130 pF 150 pF 160 pF 180 pF 200 pF 220 pF 240 pF 270 pF 300 pF 330 pF 360 pF 390 pF 430 pF 470 pF 510 pF 560 pF 620 pF 680 pF 1,000 pF 1,100 pF 1,200 pF 1,300 pF 1,500 pF 1,600 pF 1,800 pF 2,000 pF 2,200 pF Cap Cap Code 101 111 121 131 151 161 181 201 221 241 271 301 331 361 391 431 471 511 561 621 681 102 112 122 132 152 162 182 202 222 Cap Code 2 CAN08 0805 CAN12 1206 CAN13 1210 CAN17 1808 CAN18 1812 CAN19 1825 CAN21 2220 CAN22 2225 GB GB GB GB GB GD GD GH GH HE HE HE HE HE HG HG HG HG JK JK JK JK JK JK JK JK JK KE KE KE KE KE KE KE KE KE CAN18 1812 CAN19 1825 CAN21 2220 CAN22 2225 Voltage Code A Rated Voltage (VAC) 250 Capacitance Tolerance See Table 2 for chip thickness dimensions. F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M CG CG CG CG CG CG CG CG CG CG CG CG CG CG CG CG CG CG CG CG CG DN DN DN DN DP DP DG DG DG EF EG EG EG EG EG EG EB EB FM FK FK FS FS FS FS FL FL LB LC LC LC LC LC LC LA LA Rated Voltage (VAC) 250 Voltage Code A Case Size/Series 1 CAN06 0603 CAN06 0603 CAN08 0805 CAN12 1206 CAN13 1210 CAN17 1808 Not available in Flex termination. Different thickness codes between standard and flex termination options. Example: HE/HJ - Standard Termination = HE, Flexible Termination = HJ © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com KEM_C1099_250_VAC_SMD • 8/10/2020 6 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) 250 VAC AC Rated Capacitors, CAN series (Industrial Grade) Table 1B – C0G Dielectric Capacitance Range/Selection Waterfall Standard Termination cont. Case Size/Series Cap Cap Code 2,400 pF 2,700 pF 3,000 pF 3,300 pF 3,600 pF 3,900 pF 4,300 pF 4,700 pF 5,100 pF 5,600 pF 6,200 pF 6,800 pF 7,500 pF 8,200 pF 9,100 pF 10,000 pF 12,000 pF 15,000 pF 18,000 pF 22,000 pF 27,000 pF 33,000 pF 39,000 pF 47,000 pF 56,000 pF 68,000 pF 82,000 pF 0.1 µF 242 272 302 332 362 392 432 472 512 562 622 682 752 822 912 103 123 153 183 223 273 333 393 473 563 683 823 104 Cap Cap Code CAN06 0603 CAN08 0805 CAN12 1206 CAN13 1210 CAN19 1825 CAN21 2220 CAN22 2225 GH GH GH GH GH GH GH GH GK GK GK GM GM GO GO GO GH GH GH GH GK GM GO GO HG HG HG HG HG HG HG HG HE HE HE HE HE HE HG HG HG HJ HK HE HE HK HE HE HG HJ HK HK JK JK JK JK JK JK JK JK JK JK JE JE JE JE JE JE JK JL JL JN JN JN JE JE JK JL JL JN KE KE KE KE KF KF KF KF KF KF KF KF KE KE KE KE KE KF KH KJ KJ KH KJ KE KE KF KH KH CAN18 1812 CAN19 1825 CAN21 2220 CAN22 2225 A Rated Voltage (VAC) 250 Capacitance Tolerance See Table 2 for chip thickness dimensions. F F F F F F F F F F F F F F F F F F F F F F F F F F F F G G G G G G G G G G G G G G G G G G G G G G G G G G G G J J J J J J J J J J J J J J J J J J J J J J J J J J J J K K K K K K K K K K K K K K K K K K K K K K K K K K K K M M M M M M M M M M M M M M M M M M M M M M M M M M M M DG DG EB EB EB EB EC EC ED ED EE EF EF EG EG EG EG EH FL FL FL FM FM FY FY FY FS FS FE FE FF FF FF FG FG FM FM FY FS FS LA LA LA LA LB LB LC LC LB LC LC LC LA LA LA LA LA LB LC 250 Voltage Code Case Size/Series 2 CAN18 1812 Voltage Code Rated Voltage (VAC) 1 CAN17 1808 A CAN06 0603 CAN08 0805 CAN12 1206 CAN13 1210 CAN17 1808 Not available in Flex termination. Different thickness codes between standard and flex termination options. Example: HE/HJ - Standard Termination = HE, Flexible Termination = HJ © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com KEM_C1099_250_VAC_SMD • 8/10/2020 7 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) 250 VAC AC Rated Capacitors, CAN series (Industrial Grade) Table 1C – C0G Dielectric Capacitance Range/Selection Waterfall Flexible Termination Case Size/Series Cap 100 pF 110 pF 120 pF 130 pF 150 pF 160 pF 180 pF 200 pF 220 pF 240 pF 270 pF 300 pF 330 pF 360 pF 390 pF 430 pF 470 pF 510 pF 560 pF 620 pF 680 pF 1,000 pF 1,100 pF 1,200 pF 1,300 pF 1,500 pF 1,600 pF 1,800 pF 2,000 pF 2,200 pF Cap Cap Code 101 111 121 131 151 161 181 201 221 241 271 301 331 361 391 431 471 511 561 621 681 102 112 122 132 152 162 182 202 222 Cap Code 2 CAN08 0805 CAN12 1206 CAN13 1210 CAN17 1808 CAN18 1812 CAN19 1825 CAN21 2220 CAN22 2225 GB GB GB GB GB GD GD GH GH HJ HE HE HG HG HE HE JK JK JK JK JK JK JK JK JK KE KE KE KE KE KE KE KE KE CAN18 1812 CAN19 1825 CAN21 2220 CAN22 2225 Voltage Code A Rated Voltage (VAC) 250 Capacitance Tolerance See Table 2 for chip thickness dimensions. F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M CG CG CG CG CG CG CG CG CG CG CG CG CG CG CG CG CG CG CG CG CG DN DN DN DN DP DP DG DG DG EF EG EG EG EG EG EG EB EB FM FK FK FS FS FS FS FL FL LB LC LC LC LC LC LC LA LA Rated Voltage (VAC) 250 Voltage Code A Case Size/Series 1 CAN06 0603 CAN06 0603 CAN08 0805 CAN12 1206 CAN13 1210 CAN17 1808 Not available in Flex termination. Different thickness codes between standard and flex termination options. Example: HE/HJ - Standard Termination = HE, Flexible Termination = HJ © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com KEM_C1099_250_VAC_SMD • 8/10/2020 8 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) 250 VAC AC Rated Capacitors, CAN series (Industrial Grade) Table 1C – C0G Dielectric Capacitance Range/Selection Waterfall Flexible Termination cont. Case Size/Series Cap Cap Code 2,400 pF 2,700 pF 3,000 pF 3,300 pF 3,600 pF 3,900 pF 4,300 pF 4,700 pF 5,100 pF 5,600 pF 6,200 pF 6,800 pF 7,500 pF 8,200 pF 9,100 pF 10,000 pF 12,000 pF 15,000 pF 18,000 pF 22,000 pF 27,000 pF 33,000 pF 39,000 pF 47,000 pF 56,000 pF 68,000 pF 82,000 pF 0.1 µF 242 272 302 332 362 392 432 472 512 562 622 682 752 822 912 103 123 153 183 223 273 333 393 473 563 683 823 104 Cap Cap Code CAN06 0603 CAN08 0805 CAN12 1206 CAN13 1210 CAN19 1825 CAN21 2220 CAN22 2225 GH GH GH GH GH GH GH GH GK GK GK GM GM GO GO GO GH GH GH GH GK GM GO GO HE HE HE HG HG HJ HJ HJ HE HE HE HE HE HE HG HG HG HJ HK HE HE HK HE HE HG HJ HK HK JK JK JK JK JK JK JK JK JK JK JE JE JE JE JE JE JK JL JL JN JN JN JE JE JK JL JL JN KE KE KE KE KF KF KF KF KF KF KF KF KE KE KE KE KE KF KH KJ KJ KH KJ KE KE KF KH KH CAN18 1812 CAN19 1825 CAN21 2220 CAN22 2225 A Rated Voltage (VAC) 250 Capacitance Tolerance See Table 2 for chip thickness dimensions. F F F F F F F F F F F F F F F F F F F F F F F F F F F F G G G G G G G G G G G G G G G G G G G G G G G G G G G G J J J J J J J J J J J J J J J J J J J J J J J J J J J J K K K K K K K K K K K K K K K K K K K K K K K K K K K K M M M M M M M M M M M M M M M M M M M M M M M M M M M M DG DG EB EB EB EB EC EC ED ED EE EF EF EG EG EG EG EH FL FL FL FM FM FY FY FY FS FS FE FE FF FF FF FG FG FM FM FY FS FS LA LA LA LA LB LB LC LC LB LC LC LC LA LA LA LA LA LB LC 250 Voltage Code Case Size/Series 2 CAN18 1812 Voltage Code Rated Voltage (VAC) 1 CAN17 1808 A CAN06 0603 CAN08 0805 CAN12 1206 CAN13 1210 CAN17 1808 Not available in Flex termination. Different thickness codes between standard and flex termination options. Example: HE/HJ - Standard Termination = HE, Flexible Termination = HJ © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com KEM_C1099_250_VAC_SMD • 8/10/2020 9 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) 250 VAC AC Rated Capacitors, CAN series (Industrial Grade) Table 2A – Chip Thickness/Tape & Reel Packaging Quantities Thickness Code CG DN DP DG EB EC ED EE EF EG EH FE FF FG FL FM FY FK FS LA LB LC GB GD GH GK GM GO HE HG HJ HK Case Thickness ± Size Range (mm) 0603 0805 0805 0805 1206 1206 1206 1206 1206 1206 1206 1210 1210 1210 1210 1210 1210 1210 1210 1808 1808 1808 1812 1812 1812 1812 1812 1812 1825 1825 1825 1825 0.80 ± 0.10* 0.78 ± 0.10* 0.90 ± 0.10* 1.25 ± 0.15 0.78 ± 0.10 0.90 ± 0.10 1.00 ± 0.10 1.10 ± 0.10 1.20 ± 0.15 1.60 ± 0.15 1.60 ± 0.20 1.00 ± 0.10 1.10 ± 0.10 1.25 ± 0.15 1.40 ± 0.15 1.70 ± 0.20 2.00 ± 0.20 2.10 ± 0.20 2.50 ± 0.30 1.40 ± 0.15 1.60 ± 0.15 2.00 ± 0.15 1.00 ± 0.10 1.25 ± 0.15 1.40 ± 0.15 1.60 ± 0.20 2.00 ± 0.20 2.50 ± 0.20 1.40 ± 0.15 1.60 ± 0.20 2.00 ± 0.20 2.50 ± 0.20 Paper Quantity Plastic Quantity 7" Reel 13" Reel 7" Reel 13" Reel 4,000 4000 4000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 15,000 15000 15000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 2,500 4,000 4,000 2,500 2,500 2,500 2,000 2,000 2,500 2,500 2,500 2,000 2,000 2,000 2,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 500 500 1,000 1,000 500 500 0 0 0 10,000 10,000 10,000 10,000 10,000 10,000 8,000 8,000 10,000 10,000 10,000 8,000 8,000 8,000 8,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 4,000 2,000 2,000 4,000 4,000 2,000 2,000 Package quantity based on finished chip thickness specifications. © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com KEM_C1099_250_VAC_SMD • 8/10/2020 10 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) 250 VAC AC Rated Capacitors, CAN series (Industrial Grade) Table 2A – Chip Thickness/Tape & Reel Packaging Quantities cont. Thickness Code JE JK JL JN KE KF KH KJ TA TB TC QB QC QD MA MB MC SA SB SC Case Thickness ± Size Range (mm) 2220 2220 2220 2220 2225 2225 2225 2225 2824 2824 2824 3040 3040 3040 3640 3640 3640 4540 4540 4540 1.40 ± 0.15 1.60 ± 0.20 2.00 ± 0.20 2.50 ± 0.20 1.40 ± 0.15 1.60 ± 0.20 2.00 ± 0.20 2.50 ± 0.20 1.40 ± 0.15 2.00 ± 0.20 2.50 ± 0.20 1.40 ± 0.15 2.00 ± 0.20 2.50 ± 0.20 1.40 ± 0.15 2.00 ± 0.20 2.50 ± 0.20 1.40 ± 0.15 2.00 ± 0.20 2.50 ± 0.20 Paper Quantity Plastic Quantity 7" Reel 13" Reel 7" Reel 13" Reel 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1,000 1,000 500 500 1,000 1,000 500 500 750 300 300 500 500 350 250 250 250 200 200 200 4,000 4,000 2,000 2,000 4,000 4,000 2,000 2,000 Package quantity based on finished chip thickness specifications. Table 2B – Bulk Packaging Quantities Loose Packaging Packaging Type Bulk Bag (default) Packaging C-Spec N/A Case Size Packaging Quantities (pieces/unit packaging) CAN EIA (in) 06 08 0603 0805 12 13 17 18 19 21 22 1206 1210 1808 1812 1825 2220 2225 Minimum Maximum 50,000 1 20,000 For Industrial grade products ordered without a packaging, C-Spec will default to our standard "Bulk Bag" packaging. © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com KEM_C1099_250_VAC_SMD • 8/10/2020 11 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) 250 VAC AC Rated Capacitors, CAN series (Industrial Grade) Table 3 – Performance & Reliability: Test Methods & Conditions Stress Reference Test or Inspection Method Shear force per specific case size; Time: 60 ±1 second Terminal Strength AEC–Q200–006 Board Flex AEC–Q200–005 Case Size EIA Size Code Force 06 08 12 13 ≥ 17 0603 0805 1206 1210 ≥ 1808 5N 10 N 10 N 10 N 18 N Standard termination system - 2.0 mm (minimum) Flexible termination system and C0G Dielectric - 3.0 mm (minimum) Magnification 50 X. Conditions: Solderability J–STD–002 Temperature Cycling JESD22 Method JA-104 Biased Humidity MIL–STD–202 Method 103 Moisture Resistance MIL–STD–202 Method 106 AC Rated Life Test KEMET Custom Test Storage Life MIL–STD–202 Method 108 Vibration MIL–STD–202 Method 204 Mechanical Shock MIL–STD–202 Method 213 MIL–STD–202 Method 215 a) Method B, 4 hours at 155°C, dry heat at 235°C b) Method B, category 3, at 215°C c) Method D, category 3, at 260°C Resistance to Solvents 1,000 cycles (−55°C to +125°C). Measurement at 24 hours ±4 hours after test conclusion. Load humidity: 1,000 hours 85°C/85% RH and 200 VDC maximum. Add 100 KΩ resistor. Measurement at 24 hours ±4 hours after test conclusion. Low volt humidity: 1,000 hours 85°C/85% RH and 1.5 V. Add 100 KΩ resistor. Measurement at 24 hours ±4 hours after test conclusion. t = 24 hours/cycle. Steps 7a and 7b not required. Unpowered. Measurement at 24 hours ±4 hours after test conclusion. 1,000 hours at 125°C 250 Vrms 50/60 Hz Measurement at 24 hours ±2 hours after test conclusion. 125°C, 0 VDC, for 1,000 hours 5 G for 20 minutes, 12 cycles each of 3 orientations. Note: Use 8" x 5" PCB 0.031" thick 7 secure points on one long side and 2 secure points at corners of opposite sides. Parts mounted within 2" from any secure point. Test from 10 – 2,000 Hz Figure 1 of Method 213, Condition F Add aqueous wash chemical, OKEM Clean or equivalent Environmental Compliance Lead-free Lead (Pb)-free, RoHS, and REACH compliant without exemptions. © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com KEM_C1099_250_VAC_SMD • 8/10/2020 12 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) 250 VAC AC Rated Capacitors, CAN series (Industrial Grade) Table 4 – Land Pattern Design Recommendations per IPC–7351 Standard Termination EIA Size Code Metric Size Code 0603 0805 1206 1210 1808 1812 1825 2220 2225 1608 2012 3216 3225 4520 4532 4564 5650 5664 Density Level A: Maximum (Most) Land Protrusion (mm) Density Level B: Median (Nominal) Land Protrusion (mm) Density Level C: Minimum (Least) Land Protrusion (mm) C Y X V1 V2 C Y X V1 V2 C Y X V1 V2 0.90 1.00 1.60 1.60 2.30 2.15 2.15 2.75 2.70 1.15 1.35 1.35 1.35 1.75 1.60 1.60 1.70 1.70 1.10 1.55 1.90 2.80 2.30 3.60 6.90 5.50 6.90 4.00 4.40 5.60 5.65 7.40 6.90 6.90 8.20 8.10 2.10 2.60 2.90 3.80 3.30 4.60 7.90 6.50 7.90 0.80 0.90 1.50 1.50 2.20 2.05 2.05 2.65 2.60 0.95 1.15 1.15 1.15 1.55 1.40 1.40 1.50 1.50 1.00 1.45 1.80 2.70 2.20 3.50 6.80 5.40 6.80 3.10 3.50 4.70 4.70 6.50 6.00 6.00 7.30 7.20 1.50 2.00 2.30 3.20 2.70 4.00 7.30 5.90 7.30 0.60 0.75 1.40 1.40 2.10 1.95 1.95 2.55 2.50 0.75 0.95 0.95 0.95 1.35 1.20 1.20 1.30 1.30 0.90 1.35 1.70 2.60 2.10 3.40 6.70 5.30 6.70 2.40 2.80 4.00 4.00 5.80 5.30 5.30 6.60 6.50 1.20 1.70 2.00 2.90 2.40 3.70 7.00 5.60 7.00 Flexible Termination EIA Size Code Metric Size Code 0603 0805 1206 1210 1808 1812 1825 2220 2225 1608 2012 3216 3225 4520 4532 4564 5650 5664 Density Level A: Maximum (Most) Land Protrusion (mm) Density Level B: Median (Nominal) Land Protrusion (mm) Density Level C: Minimum (Least) Land Protrusion (mm) C Y X V1 V2 C Y X V1 V2 C Y X V1 V2 0.90 0.99 1.59 1.59 2.30 2.10 2.15 2.85 2.85 1.15 1.44 1.62 1.62 1.75 1.80 1.80 2.10 2.10 1.10 1.66 2.06 3.01 2.30 3.60 6.90 5.50 6.90 4.00 4.47 5.85 5.90 7.40 7.00 7.10 8.80 8.80 2.10 2.71 3.06 4.01 3.30 4.60 7.90 6.50 7.90 0.80 0.89 1.49 1.49 2.20 2.00 2.05 2.75 2.75 0.95 1.24 1.42 1.42 1.55 1.60 1.60 1.90 1.90 1.00 1.56 1.96 2.91 2.20 3.50 6.80 5.40 6.80 3.10 3.57 4.95 4.95 6.50 6.10 6.20 7.90 7.90 1.50 2.11 2.46 3.41 2.70 4.00 7.30 5.90 7.30 0.60 0.79 1.39 1.39 2.10 1.90 1.95 2.65 2.65 0.75 1.04 1.22 1.22 1.35 1.40 1.40 1.70 1.70 0.90 1.46 1.86 2.81 2.10 3.40 6.70 5.30 6.70 2.40 2.42 4.25 4.25 5.80 5.40 5.50 7.20 7.20 1.20 1.81 2.16 3.11 2.40 3.70 7.00 5.60 7.00 Density Level A: For low-density product applications. Recommended for wave solder applications and provides a wider process window for reflow solder processes. KEMET only recommends wave soldering of EIA 0603, 0805, and 1206 case sizes. Density Level B: For products with a moderate level of component density. Provides a robust solder attachment condition for reflow solder processes. Density Level C: For high component density product applications. Before adapting the minimum land pattern variations, the user should perform qualification testing based on the conditions outlined in IPC Standard 7351 (IPC-7351). Image below based on Density Level B for an EIA 1210 case size. V1 Y Y X X C C V2 Grid Placement Courtyard © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com KEM_C1099_250_VAC_SMD • 8/10/2020 13 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) 250 VAC AC Rated Capacitors, CAN series (Industrial Grade) Soldering Process Recommended Soldering Technique: • Solder wave or solder reflow for EIA case sizes 0805 and 1206 • All other EIA case sizes are limited to solder reflow only Recommended Reflow Soldering: KEMET’s family of surface mount multilayer ceramic capacitors (SMD MLCCs) are compatible with wave (single or dual), convection, IR, or vapor phase reflow techniques. Preheating these components is recommended to avoid extreme thermal stress. KEMET's recommended profile conditions for convection and IR reflow reflect the profile conditions of the IPC/J–STD–020 standard for moisture sensitivity testing. These devices can safely withstand a maximum of three reflow passes at these conditions. Preheat/Soak Temperature Minimum (TSmin) Temperature Maximum (TSmax) Termination Finish TP 100% matte Sn Time (tS) from TSmin to TSmax 150°C 200°C 60 – 120 seconds Ramp-Up Rate (TL to TP) 3°C/second maximum Liquidous Temperature (TL) 217°C Time Above Liquidous (tL) 60 – 150 seconds Peak Temperature (TP) 260°C Time Within 5°C of Maximum Peak Temperature (tP) 30 seconds maximum Ramp-Down Rate (TP to TL) 6°C/second maximum Time 25°C to Peak Temperature 8 minutes maximum TL Temperature Profile Feature tP Maximum Ramp-up Rate = 3°C/second Maximum Ramp-down Rate = 6°C/second tL Tsmax Tsmin 25 ts 25°C to Peak Time Note: All temperatures refer to the center of the package, measured on the capacitor body surface that is facing up during assembly reflow. Storage & Handling Ceramic chip capacitors should be stored in normal working environments. While the chips themselves are quite robust in other environments, solderability will be degraded by exposure to high temperatures, high humidity, corrosive atmospheres, and long term storage. Packaging materials will be degraded by high temperature – reels may soften or warp, and tape peel force may increase. KEMET recommends that maximum storage temperature not exceed 40°C and maximum storage humidity not exceed 70% relative humidity. Temperature fluctuations should be minimized to avoid condensation on the parts and atmospheres should be free of chlorine and sulfur bearing compounds. For optimized solderability, chip stock should be used promptly, preferably within 1.5 years upon receipt. © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com KEM_C1099_250_VAC_SMD • 8/10/2020 14 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) 250 VAC AC Rated Capacitors, CAN series (Industrial Grade) Construction Standard Termination Detailed Cross Section Dielectric Material* Shield Electrodes (Ni) Dielectric Barrier Layer Material* (Ni) End Termination/ External Electrode Termination Finish (Cu) (100% Matte Sn) Inner Electrodes (Ni) Shield Electrodes End Termination/ (Ni) External Electrode (Cu) Barrier Layer (Ni) * Dielectric Material C0G: CaZrO3 X7R: BaTiO3 Inner Electrodes (Ni) Termination Finish (100% Matte Sn) Shield Electrode (Ni) Flexible Termination Detailed Cross Section Shield Electrodes (Ni) Dielectric Material* Barrier Layer (Ni) Termination Finish (100% Matte Sn) End Termination/ External Electrode (Cu) Epoxy Layer (Ag) Dielectric Material* Inner Electrodes (Ni) Shield Electrodes End Termination/ (Ni) External Electrode (Cu) Epoxy Layer (Ag) * Dielectric Material C0G: CaZrO3 X7R: BaTiO3 Inner Electrodes (Ni) Shield Electrode (Ni) © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com Barrier Layer (Ni) Termination Finish (100% Matte Sn) KEM_C1099_250_VAC_SMD • 8/10/2020 15 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) 250 VAC AC Rated Capacitors, CAN series (Industrial Grade) Capacitor Marking (Optional) These surface mount multilayer ceramic capacitors are normally supplied unmarked. If required, they can be marked as an extra cost option. Marking is available on most KEMET devices, but must be requested using the correct ordering code identifier(s). If this option is requested, two sides of the ceramic body will be laser marked with a “K” to identify KEMET, followed by two characters (per EIA–198 - see table below) to identify the capacitance value. EIA 0603 case size devices are limited to the “K” character only. Marking appears in legible contrast. Illustrated below is an example of an MLCC with laser marking of “KA8”, which designates a KEMET device with rated capacitance of 100 µF. Orientation of marking is vendor optional. KEMET ID 2-Digit Capacitance Code Laser marking option is not available on: • C0G, ultra stable X8R and Y5V dielectric devices. • EIA 0402 case size devices. • EIA 0603 case size devices with flexible termination option. • KPS commercial and automotive grade stacked devices. • X7R dielectric products in capacitance values outlined below. EIA Case Size Metric Size Code Capacitance 0603 0805 1206 1210 1808 1812 1825 2220 2225 1608 2012 3216 3225 4520 4532 4564 5650 5664 ≤ 170 pF ≤ 150 pF ≤ 910 pF ≤ 2,000 pF ≤ 3,900 pF ≤ 6,700 pF ≤ 0.018 µF ≤ 0.027 µF ≤ 0.033 µF © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com KEM_C1099_250_VAC_SMD • 8/10/2020 16 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) 250 VAC AC Rated Capacitors, CAN series (Industrial Grade) Capacitor Marking (Optional) cont. Capacitance (pF) For Various Alpha/Numeral Identifiers Numeral Alpha Character 9 A 0.10 1.0 10 100 1,000 10,000 B 0.11 1.1 11 110 1,100 11,000 C 0.12 1.2 12 120 1,200 12,000 D 0.13 1.3 13 130 1,300 E 0.15 1.5 15 150 1,500 0 1 2 3 4 5 6 7 8 100,000 1,000,000 10,000,000 100,000,000 110,000 1,100,000 11,000,000 110,000,000 120,000 1,200,000 12,000,000 120,000,000 13,000 130,000 1,300,000 13,000,000 130,000,000 15,000 150,000 1,500,000 15,000,000 150,000,000 160,000,000 Capacitance (pF) F 0.16 1.6 16 160 1,600 16,000 160,000 1,600,000 16,000,000 G 0.18 1.8 18 180 1,800 18,000 180,000 1,800,000 18,000,000 180,000,000 H 0.20 2.0 20 200 2,000 20,000 200,000 2,000,000 20,000,000 200,000,000 J 0.22 2.2 22 220 2,200 22,000 220,000 2,200,000 22,000,000 220,000,000 K 0.24 2.4 24 240 2,400 24,000 240,000 2,400,000 24,000,000 240,000,000 L 0.27 2.7 27 270 2,700 27,000 270,000 2,700,000 27,000,000 270,000,000 M 0.30 3.0 30 300 3,000 30,000 300,000 3,000,000 30,000,000 300,000,000 N 0.33 3.3 33 330 3,300 33,000 330,000 3,300,000 33,000,000 330,000,000 P 0.36 3.6 36 360 3,600 36,000 360,000 3,600,000 36,000,000 360,000,000 Q 0.39 3.9 39 390 3,900 39,000 390,000 3,900,000 39,000,000 390,000,000 R 0.43 4.3 43 430 4,300 43,000 430,000 4,300,000 43,000,000 430,000,000 470,000,000 S 0.47 4.7 47 470 4,700 47,000 470,000 4,700,000 47,000,000 T 0.51 5.1 51 510 5,100 51,000 510,000 5,100,000 51,000,000 510,000,000 U 0.56 5.6 56 560 5,600 56,000 560,000 5,600,000 56,000,000 560,000,000 V 0.62 6.2 62 620 6,200 62,000 620,000 6,200,000 62,000,000 620,000,000 W 0.68 6.8 68 680 6,800 68,000 680,000 6,800,000 68,000,000 680,000,000 X 0.75 7.5 75 750 7,500 75,000 750,000 7,500,000 75,000,000 750,000,000 Y 0.82 8.2 82 820 8,200 82,000 820,000 8,200,000 82,000,000 820,000,000 Z 0.91 9.1 91 910 9,100 91,000 910,000 9,100,000 91,000,000 910,000,000 a 0.25 2.5 25 250 2,500 25,000 250,000 2,500,000 25,000,000 250,000,000 b 0.35 3.5 35 350 3,500 35,000 350,000 3,500,000 35,000,000 350,000,000 d 0.40 4.0 40 400 4,000 40,000 400,000 4,000,000 40,000,000 400,000,000 e 0.45 4.5 45 450 4,500 45,000 450,000 4,500,000 45,000,000 450,000,000 f 0.50 5.0 50 500 5,000 50,000 500,000 5,000,000 50,000,000 500,000,000 m 0.60 6.0 60 600 6,000 60,000 600,000 6,000,000 60,000,000 600,000,000 n 0.70 7.0 70 700 7,000 70,000 700,000 7,000,000 70,000,000 700,000,000 t 0.80 8.0 80 800 8,000 80,000 800,000 8,000,000 80,000,000 800,000,000 y 0.90 9.0 90 900 9,000 90,000 900,000 9,000,000 90,000,000 900,000,000 © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com KEM_C1099_250_VAC_SMD • 8/10/2020 17 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) 250 VAC AC Rated Capacitors, CAN series (Industrial Grade) Tape & Reel Packaging Information KEMET offers multilayer ceramic chip capacitors packaged in 8, 12 and 16 mm tape on 7" and 13" reels in accordance with EIA Standard 481. This packaging system is compatible with all tape-fed automatic pick and place systems. See Table 2 for details on reeling quantities for commercial chips. Bar code label Anti-static reel ® Embossed plastic* or punched paper carrier. ET KEM Chip and KPS orientation in pocket (except 1825 commercial, and 1825 and 2225 Military) Sprocket holes Embossment or punched cavity 8 mm, 12 mm or 16 mm carrier tape 180 mm (7.00") or 330 mm (13.00") Anti-static cover tape (0.10 mm (0.004") maximum thickness) *EIA 01005, 0201, 0402 and 0603 case sizes available on punched paper carrier only. Table 5 – Carrier Tape Configuration, Embossed Plastic & Punched Paper (mm) EIA Case Size Tape Size (W)* Embossed Plastic 7" Reel 13" Reel Pitch (P1)* Punched Paper 7" Reel 13" Reel Pitch (P1)* 0603 8 – – 2/4 2/4 0805 8 4 4 4 4 1206 – 1210 8 4 4 4 4 1805 – 1808 12 4 4 – – ≥ 1812 12 8 8 – – *Refer to Figures 1 and 2 for W and P1 carrier tape reference locations. *Refer to Tables 7 and 8 for tolerance specifications. © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com KEM_C1099_250_VAC_SMD • 8/10/2020 18 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) 250 VAC AC Rated Capacitors, CAN series (Industrial Grade) Figure 1 – Embossed (Plastic) Carrier Tape Dimensions P2 T T2 ØD0 (10 pitches cumulative tolerance on tape ±0.2 mm) P0 A0 E1 F K0 B1 S1 W E2 B0 P1 T1 Center Lines of Cavity ØD1 Cover Tape B1 is for tape feeder reference only, including draft concentric about B0. Embossment For cavity size, see Note 1 Table 4 User Direction of Unreeling Table 6 – Embossed (Plastic) Carrier Tape Dimensions Metric will govern Constant Dimensions — Millimeters (Inches) Tape Size D0 8 mm 12 mm 16 mm 1.5 +0.10/−0.0 (0.059 +0.004/−0.0) D1 Minimum Note 1 1.0 (0.039) 1.5 (0.059) R Reference S1 Minimum T Note 2 Note 3 Maximum 25.0 (0.984) 0.600 0.600 (0.024) (0.024) 30 1.75 ±0.10 4.0 ±0.10 2.0 ±0.05 (1.181) (0.069 ±0.004) (0.157 ±0.004) (0.079 ±0.002) E1 P0 P2 30.0 (1.181) 24 mm 5.0 (0.196) 0.250 (0.009) T1 Maximum 0.100 (0.004) 0.350 (0.013) Variable Dimensions — Millimeters (Inches) Tape Size 8 mm 12 mm 16 mm 24 mm B1 Maximum Pitch Note 4 4.35 Single (4 mm) (0.171) Single (4 mm) 8.2 and Double (8 mm) (0.323) 12.1 Triple (12 mm) (0.476) 11.5 16 mm (0.452) E2 Minimum 6.25 (0.246) 10.25 (0.404) 14.25 (0.561) 22.25 (0.875) F P1 3.5 ±0.05 (0.138 ±0.002) 5.5 ±0.05 (0.217 ±0.002) 7.5 ±0.05 (0.138 ±0.002) 11.5 ±0.10 (0.452 ±0.003) 4.0 ±0.10 (0.157 ±0.004) 8.0 ±0.10 (0.315 ±0.004) 12.0 ±0.10 (0.157 ±0.004) 16.0 ±0.10 (0.629 ±0.004) T2 Maximum 2.5 (0.098) 4.6 (0.181) 4.6 (0.181) 3 (0.118) W Maximum 8.3 (0.327) 12.3 (0.484) 16.3 (0.642) 24.3 (0.956) A0,B0 & K0 Note 5 1. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of the embossment location and the hole location shall be applied independently of each other. 2. The tape with or without components shall pass around R without damage (see Figure 6). 3. If S1 < 1.0 mm, there may not be enough area for a cover tape to be properly applied (see EIA Standard 481, paragraph 4.3, section b.) 4. B1 dimension is a reference dimension for tape feeder clearance only. 5. The cavity defined by A0, B0 and K0 shall surround the component with sufficient clearance that: (a) the component does not protrude above the top surface of the carrier tape. (b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the top cover tape has been removed. (c) rotation of the component is limited to 20° maximum for 8 and 12 mm tapes and 10° maximum for 16 mm tapes (see Figure 3). (d) lateral movement of the component is restricted to 0.5 mm maximum for 8 and 12 mm wide tape and to 1.0 mm maximum for 16 mm tape (see Figure 4). (e) for KPS product, A0 and B0 are measured on a plane 0.3 mm above the bottom of the pocket. (f) see addendum in EIA Standard 481 for standards relating to more precise taping requirements. © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com KEM_C1099_250_VAC_SMD • 8/10/2020 19 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) 250 VAC AC Rated Capacitors, CAN series (Industrial Grade) Packaging Information Performance Notes 1. Cover Tape Break Force: 1.0 kg minimum. 2. Cover Tape Peel Strength: The total peel strength of the cover tape from the carrier tape shall be: Tape Width Peel Strength 8 mm 0.1 to 1.0 newton (10 to 100 gf) 12 and 16 mm 0.1 to 1.3 newton (10 to 130 gf) The direction of the pull shall be opposite the direction of the carrier tape travel. The pull angle of the carrier tape shall be 165° to 180° from the plane of the carrier tape. During peeling, the carrier and/or cover tape shall be pulled at a velocity of 300 ±10 mm/minute. 3. Labeling: Bar code labeling (standard or custom) shall be on the side of the reel opposite the sprocket holes. Refer to EIA Standards 556 and 624. Figure 2 – Maximum Component Rotation ° T Maximum Component Rotation Top View Maximum Component Rotation Side View Typical Pocket Centerline Tape Maximum Width (mm) Rotation ( 8,12 20 16 – 200 10 Bo ° T) ° s Tape Width (mm) 8,12 16 – 56 72 – 200 Typical Component Centerline Ao Figure 3 – Maximum Lateral Movement 8 mm & 12 mm Tape 0.5 mm maximum 0.5 mm maximum Maximum Rotation ( 20 10 5 ° S) Figure 4 – Bending Radius Embossed Carrier 16 mm Tape Punched Carrier 1.0 mm maximum 1.0 mm maximum R © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com Bending Radius R KEM_C1099_250_VAC_SMD • 8/10/2020 20 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) 250 VAC AC Rated Capacitors, CAN series (Industrial Grade) Figure 5 – Reel Dimensions Full Radius, See Note W3 (Includes flange distortion at outer edge) Access Hole at Slot Location (Ø 40 mm minimum) W2 D A (See Note) N C (Arbor hole diameter) B (see Note) (Measured at hub) W1 (Measured at hub) If present, tape slot in core for tape start: 2.5 mm minimum width x 10.0 mm minimum depth Note: Drive spokes optional; if used, dimensions B and D shall apply. Table 7 – Reel Dimensions Metric will govern Constant Dimensions — Millimeters (Inches) Tape Size 8 mm 12 mm 16 mm 24 mm A B Minimum C D Minimum 178 ±0.20 (7.008 ±0.008) or 330 ±0.20 (13.000 ±0.008) 1.5 (0.059) 13.0 +0.5/−0.2 (0.521 +0.02/−0.008) 20.2 (0.795) 1.2 (0.047) 13.0 ±0.2 (0.521 ±0.008) 21 (0.826) Variable Dimensions — Millimeters (Inches) Tape Size N Minimum W1 W2 Maximum W3 50 (1.969) 8.4 +1.5/−0.0 (0.331 +0.059/−0.0) 12.4 +2.0/−0.0 (0.488 +0.078/−0.0) 16.4 +2.0/−0.0 (0.646 +0.078/−0.0) 25 +1.0/−0.0 (0.984 +0.039/−0.0) 14.4 (0.567) 18.4 (0.724) 22.4 (0.882) 27.4 +1.0/−1.0 (1.078 +0.039/−0.039) Shall accommodate tape width without interference 8 mm 12 mm 16 mm 24 mm © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com KEM_C1099_250_VAC_SMD • 8/10/2020 21 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) 250 VAC AC Rated Capacitors, CAN series (Industrial Grade) Figure 6 – Tape Leader & Trailer Dimensions Embossed Carrier Punched Carrier 8 mm & 12 mm only END Carrier Tape Round Sprocket Holes START Top Cover Tape Elongated Sprocket Holes (32 mm tape and wider) Trailer 160 mm minimum Components 100 mm minimum leader 400 mm minimum Top Cover Tape Figure 7 – Maximum Camber Elongated Sprocket Holes (32 mm & wider tapes) Carrier Tape Round Sprocket Holes 1 mm maximum, either direction Straight Edge 250 mm © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com KEM_C1099_250_VAC_SMD • 8/10/2020 22 Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) 250 VAC AC Rated Capacitors, CAN series (Industrial Grade) KEMET Electronics Corporation Sales Offices For a complete list of our global sales offices, please visit www.kemet.com/sales. Disclaimer All product specifications, statements, information and data (collectively, the “Information”) in this datasheet are subject to change. The customer is responsible for checking and verifying the extent to which the Information contained in this publication is applicable to an order at the time the order is placed. All Information given herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied. Statements of suitability for certain applications are based on KEMET Electronics Corporation’s (“KEMET”) knowledge of typical operating conditions for such applications, but are not intended to constitute – and KEMET specifically disclaims – any warranty concerning suitability for a specific customer application or use. The Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by KEMET with reference to the use of KEMET’s products is given gratis, and KEMET assumes no obligation or liability for the advice given or results obtained. Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. Although all product–related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicted or that other measures may not be required. KEMET is a registered trademark of KEMET Electronics Corporation. © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com KEM_C1099_250_VAC_SMD • 8/10/2020 23