F43KR3500ZA01K

AC Line EMI Suppression and RC Networks F43 Metallized Polypropylene RC Snubber Film, 160 – 220 VAC/250 – 630 VDC; 275 VAC Class X2 Overview Applications The F43 is constructed of metallized polypropylene film encapsulated with self-extinguishing resin in a box of material that meets the requirements of UL 94 V–0. Typical applications include worldwide use in contact protection, contact interference suppression, and transient suppression. Benefits • Approvals (for 275 VAC only): ENEC, UL • Rated voltage: 160 VAC/250 VDC, 200 VAC/400 VDC, 220 VAC/630 VDC, 275 VAC Class X2 • Capacitance range: 0.01 – 1.0 µF • Lead spacing: 15.0 – 27.5 mm • Capacitance tolerance: ±20%, ±10% • Resistance range: 22 – 470 Ω • Resistance tolerance: ±10% • Resistance power: 0.5 W • Climatic category: 55/100/56, IEC 60068–1 and 40/100/56 (275 VAC), IEC 60068–1 • Tape & Reel packaging in accordance with IEC 60286-2 • RoHS compliance and lead (Pb)-free terminations • Operating temperature range: –55°C to +100°C and –40°C to +100°C (275 VAC) Click image above for interactive 3D content Open PDF in Adobe Reader for full functionality Part Number System F Capacitor Class 43 K N 3100 XX 01 K R101 Series Rated Voltage (VAC) Lead Spacing (mm) Capacitance Code (pF) Packaging Internal Use Capacitance Tolerance Resistance (Ω) Legacy PN: RC Snubber, F Metallized New KEMET PN: Polypropylene Omit this character I = 160 I = 15.0 M = 200 N = 22.5 P = 220 R = 27.5 K = 275 (X2) The last three See Ordering 00, 01, 04 digits represent Option Table. (Standard) significant Contact KEMET figures. The for other first digit packaging specifies availability and number of details. zeros to be added. K = ±10% M = ±20% R plus first two digits represent significant figures. Third digit specifies number of zeros. One world. One KEMET © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com F3023_F43 • 3/15/2019 1 Film Capacitors – AC Line EMI Suppression and RC Networks F43 Metallized Polypropylene RC Snubber Film, 160 – 220 VAC/250 – 630 VDC; 275 VAC Class X2 Ordering Options Table Lead Spacing Nominal (mm) Type of Leads and Packaging Lead Length (mm) Lead and Packaging Code 4 +2/−0 H0 = 18.5 ±0.5 00 DQ H0 = 18.5 ±0.5 30 +5/−0 25 +2/−1 30 +5/-0 (sp 8 ±2) 150 ±5 (sp 8 ±2) CK 40 50 51 52 Standard Lead and Packaging Options Bulk (Bag) – Short leads Ammo Pack 15 22.5 27.5 Other Lead and Packaging Options Tape & Reel (Large Reel Ø = 500 mm) Bulk (Bag) – Long leads Bulk (Bag) – Long leads Bulk (Bag) – Insulated Rigid Leads Bulk (Bag) – Insulated Flexible Leads Contact KEMET for availability and details for special leads or packing. Dimensions – Millimeters Insulated Rigid Leads B L B H 8 ±2 LL p Ød1 p B B H 8 ±2 H d L 35 +0/−5 L Insulated Flexible Leads 0.5 mm2 H 150 ±5 Loose L d d1 Nominal Tolerance Nominal Tolerance Nominal Tolerance Nominal Tolerance Nominal Tolerance Nominal Tolerance 15.0 15.0 15.0 15.0 22.5 22.5 22.5 22.5 22.5 27.5 27.5 27.5 ±0.4 ±0.4 ±0.4 ±0.4 ±0.4 ±0.4 ±0.4 ±0.4 ±0.4 ±0.4 ±0.4 ±0.4 6.0 7.5 8.5 10.0 6.0 7.0 8.5 10.0 11.0 11.0 13.0 18.0 +0.2 +0.2 +0.2 +0.2 +0.2 +0.2 +0.2 +0.2 +0.2 +0.2 +0.2 +0.2 17.5 14.5 14.5 16.0 15.0 16.0 17.0 18.5 20.0 20.0 22.0 33.0 +0.1 +0.1 +0.1 +0.1 +0.1 +0.1 +0.1 +0.1 +0.1 +0.1 +0.1 +0.1 18.0 18.0 18.0 18.0 26.5 26.5 26.5 26.5 26.5 32.0 32.0 32.0 +0.3 +0.5 +0.5 +0.5 +0.3 +0.3 +0.3 +0.3 +0.3 +0.3 +0.3 +0.3 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.8 0.8 0.8 0.8 0.8 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 Note: See the Ordering Options Table for lead length (LL) options. © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com F3023_F43 • 3/15/2019 2 Film Capacitors – AC Line EMI Suppression and RC Networks F43 Metallized Polypropylene RC Snubber Film, 160 – 220 VAC/250 – 630 VDC; 275 VAC Class X2 Performance Characteristics Rated Voltage Capacitance Range Capacitance Tolerance Temperature Range Climatic Category Approvals 160 VAC/250 VDC, 200 VAC/400 VDC, 220 VAC/630 VDC, 275 VAC, Class X2 0.01 – 1.0 µF ±10%, ±20% −55°C to +100°C, −40°C to +100°C (275 VAC) 55/100/56, 40/100/56 (275 VAC) ENEC, UL Maximum Values at +23°C Dissipation Factor Test Voltage Between Terminals Frequency tanδ 1 kHz 0.1% The 100% screening factory test is carried out at 1.6 UR, 4.3 UR for 275 VAC. The voltage level is selected to meet the requirements in applicable equipment standards. All electrical characteristics are checked after the test. This test may not be repeated due to potential capacitor damage. KEMET is not liable for any failures that result from re-testing. Between Terminals Insulation Resistance In DC Applications C ≤ 0.33 µF ≥ 10,000 MΩ C > 0.33 µF ≥ 3,000 MΩ • µF Recommended voltage ≤ 800 VDC Environmental Test Data Test IEC Publication Procedure Vibration IEC 60068–2–6 Test Fc 3 directions at 2 hours each 10 – 500 Hz at 0.75 mm or 98 m/seconds2 Bump IEC 60068–2–29 Test Eb 4,000 bumps at 390 m/seconds2 Solderability IEC 60068–2–20 Test Ta Wetting time d or d > 0.8 < 1.5 seconds Active Flammability IEC 60384–14 VR +20 surge pulses at 2.5 kV (pulse every 5 seconds) Passive Flammability IEC 60384–14 IEC 60384–1, IEC 60695–11–5 needle flame test Damp Heat Steady State IEC 60068–2–78 Test Cab +40°C and 93% R.H., 56 days © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com F3023_F43 • 3/15/2019 3 Film Capacitors – AC Line EMI Suppression and RC Networks F43 Metallized Polypropylene RC Snubber Film, 160 – 220 VAC/250 – 630 VDC; 275 VAC Class X2 Approvals Certification Body Specification File Number EN/IEC 60384–14 CA08.00032 UL 60384–14 and CAN/CSA–E60384–14 E97797 Environmental Compliance All KEMET EMI capacitors are RoHS compliant. Circuit Drawings Mounting: RC units are mounted parallel to the contacts to be protected or parallel to the inductive load (Figures 1 and 2). RC units are generally mounted parallel to the contacts to suppress radio interference (Figure 1). R Figure 1 C Figure 2 R C © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com F3023_F43 • 3/15/2019 4 Film Capacitors – AC Line EMI Suppression and RC Networks F43 Metallized Polypropylene RC Snubber Film, 160 – 220 VAC/250 – 630 VDC; 275 VAC Class X2 Table 1 – Ratings & Part Number Reference VAC VDC Capacitance Value (µF) 160 160 160 160 160 250 250 250 250 250 200 200 200 220 220 220 220 Lead Spacing (p) New KEMET Part Number Legacy Part Number B H L 0.25 0.33 0.47 0.5 1 8.5 6.0 8.5 8.5 10.0 14.5 15.0 17.0 17.0 18.5 18.0 26.5 26.5 26.5 26.5 15.0 22.5 22.5 22.5 22.5 43II3250(1)01(2)(3) 43IN3330(1)01(2)(3) 43IN3470(1)01(2)(3) 43IN3500(1)01(2)(3) 43IN4100(1)01(2)(3) F43II3250(1)01(2)(3) F43IN3330(1)01(2)(3) F43IN3470(1)01(2)(3) F43IN3500(1)01(2)(3) F43IN4100(1)01(2)(3) 400 400 400 0.25 0.5 1 7.0 10.0 13.0 16.0 18.5 22.0 26.5 26.5 32.0 22.5 22.5 27.5 43MN3250(1)01(2)(3) 43MN3500(1)01(2)(3) 43MR4100(1)01(2)(3) F43MN3250(1)01(2)(3) F43MN3500(1)01(2)(3) F43MR4100(1)01(2)(3) 630 630 630 630 0.022 0.1 0.25 0.5 7.5 7.0 11.0 13.0 14.5 16.0 20.0 22.0 18.0 26.5 26.5 32.0 15.0 22.5 22.5 27.5 43PI2220(1)01(2)(3) 43PN3100(1)01(2)(3) 43PN3250(1)01(2)(3) 43PR3500(1)01(2)(3) F43PI2220(1)01(2)(3) F43PN3100(1)01(2)(3) F43PN3250(1)01(2)(3) F43PR3500(1)01(2)(3) 0.01 0.015 0.022 0.033 0.047 0.068 0.1 0.15 0.22 0.25 0.33 0.47 0.5 0.68 1 7.5 7.5 7.5 7.5 7.5 10.0 8.5 10.0 11.0 11.0 11.0 13.0 13.0 18.0 18.0 14.5 14.5 14.5 14.5 14.5 16.0 17.0 18.5 20.0 20.0 20.0 22.0 22.0 33.0 33.0 18.0 18.0 18.0 18.0 18.0 18.0 26.5 26.5 26.5 32.0 32.0 32.0 32.0 32.0 32.0 15.0 15.0 15.0 15.0 15.0 15.0 22.5 22.5 22.5 27.5 27.5 27.5 27.5 27.5 27.5 43KI2100(1)01(2)(3) 43KI2150(1)01(2)(3) 43KI2220(1)01(2)(3) 43KI2330(1)01(2)(3) 43KI2470(1)01(2)(3) 43KI2680(1)01(2)(3) 43KN3100(1)01(2)(3) 43KN3150(1)01(2)(3) 43KN3220(1)01(2)(3) 43KR3250(1)01(2)(3) 43KR3330(1)01(2)(3) 43KR3470(1)01(2)(3) 43KR3500(1)01(2)(3) 43KR3680(1)01(2)(3) 43KR4100(1)01(2)(3) F43KI2100(1)01(2)(3) F43KI2150(1)01(2)(3) F43KI2220(1)01(2)(3) F43KI2330(1)01(2)(3) F43KI2470(1)01(2)(3) F43KI2680(1)01(2)(3) F43KN3100(1)01(2)(3) F43KN3150(1)01(2)(3) F43KN3220(1)01(2)(3) F43KR3250(1)01(2)(3) F43KR3330(1)01(2)(3) F43KR3470(1)01(2)(3) F43KR3500(1)01(2)(3) F43KR3680(1)01(2)(3) F43KR4100(1)01(2)(3) Capacitance Value (µF) B (mm) H (mm) L (mm) Lead Spacing (p) New KEMET Part Number Legacy Part Number 275 (X2) 275 (X2) 275 (X2) 275 (X2) 275 (X2) 275 (X2) 275 (X2) 275 (X2) 275 (X2) 275 (X2) 275 (X2) 275 (X2) 275 (X2) 275 (X2) 275 (X2) VAC Max Dimensions in mm VDC (1) Lead and packaging code. Contact KEMET for availability and details. (2) M = ±20%, K = ±10%. (3) Resistance value [Ω] - R plus first two digits represent significant figures. Third digit specifies number of zeros: R220 = 22 Ω R470 = 47 Ω R101 = 100 Ω R221 = 220 Ω R471 = 470 Ω © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com F3023_F43 • 3/15/2019 5 Film Capacitors – AC Line EMI Suppression and RC Networks F43 Metallized Polypropylene RC Snubber Film, 160 – 220 VAC/250 – 630 VDC; 275 VAC Class X2 Soldering Process The implementation of the RoHS directive has resulted in the selection of SnAuCu (SAC) alloys or SnCu alloys as primary solder. This has increased the liquidus temperature from that of 183ºC for SnPb eutectic alloy to 217 – 221ºC for the new alloys. As a result, the heat stress to the components, even in wave soldering, has increased considerably due to higher pre-heat and wave temperatures. Polypropylene capacitors are especially sensitive to heat (the melting point of polypropylene is 160 – 170ºC). Wave soldering can be destructive, especially for mechanically small polypropylene capacitors (with lead spacing of 5 – 15 mm), and great care must be taken during soldering. The recommended solder profiles from KEMET should be used. Consult KEMET with any questions. In general, the wave soldering curve from IEC Publication 61760-1 Edition 2 serves as a solid guideline for successful soldering. See Figure 1. Reflow soldering is not recommended for through-hole film capacitors. Exposing capacitors to a soldering profile in excess of the recommended limits may result in degradation of or permanent damage to the capacitors. Do not place the polypropylene capacitor through an adhesive curing oven to cure resin for surface-mount components. Insert through-hole parts after curing the surface-mount parts. Consult KEMET to discuss the actual temperature profile in the oven, if through-hole components must pass through the adhesive curing process. A maximum of two soldering cycles is recommended. Allow time for the capacitor surface temperature to return to a normal temperature before the second soldering cycle. Wave Soldering Recommendations Manual Soldering Recommendations 300 Following is the recommendation for manual soldering with a soldering iron. 2 +3 seconds maximum 260°C 250 First wave 200 Temperature (°C) Recommended Soldering Temperature 400 350 Soldering Iron Bit Temperature (°C) Second wave 300 Cooling ∆T < 150°C Preheating 150 ca 2°C/second ca 3.5°C/second typical T preheat 100 ca 5°C/second 115 °C max 100 °C Typical 250 50 200 150 0 0 100 40 80 120 160 200 240 Time (s) 50 0 0 1 2 3 4 5 6 7 8 Soldering Time (seconds) Soldering iron tip temperature should be set at 350°C (+10°C maximum), with the soldering duration not to exceed more than 3 seconds. © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com F3023_F43 • 3/15/2019 6 Film Capacitors – AC Line EMI Suppression and RC Networks F43 Metallized Polypropylene RC Snubber Film, 160 – 220 VAC/250 – 630 VDC; 275 VAC Class X2 Soldering Process cont'd Wave Soldering Recommendations cont'd 1. The table indicates the maximum setup temperature for the soldering process. Dielectric film material Maximum Preheat Temperature Maximum Peak Soldering Temperature Capacitor Capacitor Capacitor Capacitor Capacitor Pitch ≤ 10 mm Pitch = 15 mm Pitch > 15 mm Pitch ≤ 15 mm Pitch > 15 mm Polyester 130°C 130°C 130°C 270°C 270°C Polypropylene 100°C 110°C 130°C 260°C 270°C Paper 130°C 130°C 140°C 270°C 270°C Polyphenylene Sulphide 150°C 150°C 160°C 270°C 270°C 2. The maximum temperature measured inside the capacitor: set the temperature so that inside the element the maximum temperature is below the limit. Dielectric Film Material Maximum Temperature Measured Inside the Element Polyester 160°C Polypropylene 110°C Paper 160°C Polyphenylene Sulphide 160°C Temperature monitored inside the capacitor. Selective Soldering Recommendations Selective dip soldering is a variation of reflow soldering. In this method, the printed circuit board with through-hole components to be soldered is preheated and transported over the solder bath, as in normal flow soldering, without touching the solder. When the board is over the bath, it is stopped. Pre-designed solder pots are lifted from the bath with molten solder, only at the places of the selected components, and pressed against the lower surface of the board to solder the components. The temperature profile for selective soldering is similar to the double wave flow soldering outlined in this document. However, instead of two baths, there is only one with a time from 3 to 10 seconds. In selective soldering, the risk of overheating is greater than in double wave flow soldering. Great care must be taken so that the parts do not overheat. © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com F3023_F43 • 3/15/2019 7 Film Capacitors – AC Line EMI Suppression and RC Networks F43 Metallized Polypropylene RC Snubber Film, 160 – 220 VAC/250 – 630 VDC; 275 VAC Class X2 Marking • KEMET’s logo • Series • Capacitance • Rated resistance • Rated voltage • Capacitor class • Approval marks • IEC climatic category • Passive flammability class • Manufacturing date code Packaging Quantities Height (mm) Length (mm) Bulk Short Leads Lead Spacing Thickness (mm) 15 6.0 7.5 8.5 10.0 Packaging Codes 17.5 14.5 14.5 16.0 18.0 18.0 18.0 18.0 00 1,000 1,000 1,000 750 40 – 50 700 700 500 500 51 700 500 500 500 52 250 250 250 250 22.5 6.0 7.5 8.5 10.0 11.0 15.0 16.0 17.0 18.5 20.0 26.5 26.5 26.5 26.5 26.5 805 700 468 396 360 500 500 300 300 250 500 400 300 250 200 250 250 200 200 200 27.5 11.0 13.0 18.0 20.0 22.0 33.0 32.0 32.0 32.0 600 480 256 336 288 128 336 288 128 150 150 150 © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com Bulk Long Leads F3023_F43 • 3/15/2019 8 Film Capacitors – AC Line EMI Suppression and RC Networks F43 Metallized Polypropylene RC Snubber Film, 160 – 220 VAC/250 – 630 VDC; 275 VAC Class X2 Lead Taping & Packaging (IEC 60286–2) Figure 1 Lead Spacing 15 mm Figure 2 Lead Spacing 22.5 and 27.5 mm P W2 P2 h ød P1 P0 A B W W0 W1 H0 F P h D0 P1 P2 A-B t Taping Specification Dimensions (mm) Description Symbol 15 Figure 1 Lead Space 22.5 Figure 2 27.5 Figure 2 Tolerance Lead Wire Diameter d 0.6 – 0.8 0.8 0.8 ±0.05 Taping Lead Space P 25.4 38.1 38.1 ±1 Feed-hole Lead Space* P0 12.7 12.7 12.7 ±0.2** Centering of the Lead Wire P1 5.2 7.8 5.3 ±0.7 Centering of the Body P2 12.7 19.05 19.05 ±1.3 Lead Spacing (Pitch)*** F 15 22.5 27.5 +0.6/−0.1 Component Alignment ∆h 0 0 0 ±2 Height of Component from Tape Center H0 **** 18.5 18.5 18.5 ±0.5 Carrier Tape Width W 18.0 18.0 18.0 +1/−0.5 Hold Down Tape Width W0 10.0 10.0 10.0 Minimum Hole Position W1 10.0 10.0 10.0 ±0.5 Hold Down Tape Position W2 3.0 3.0 3.0 Maximum Feed-hole Diameter D0 4.0 4.0 4.0 ±0.2 Total Tape Thickness t 0.7 0.7 0.7 ±0.2 * Available also in 15 mm ** Maximum 1 mm on 20 lead spaces *** Pitches 15 mm and 10 mm taped to 7.5 mm (crimped leads) available upon request **** H0 = 16.5 mm available upon request © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com F3023_F43 • 3/15/2019 9 Film Capacitors – AC Line EMI Suppression and RC Networks F43 Metallized Polypropylene RC Snubber Film, 160 – 220 VAC/250 – 630 VDC; 275 VAC Class X2 Lead Taping & Packaging (IEC 60286–2) cont'd Ammo Specifications Dimensions (mm) H W T 360 340 59 H T W Reel Specifications Dimensions (mm) D H W 355 500 30 25 55 Maximum D Manufacturing Date Code (IEC–60062) H W Y = Year, Z = Month Year 2010 2011 2012 2013 2014 2015 2016 2017 2018 2019 2020 2021 2022 2023 2024 2025 2026 2027 2028 2029 2030 Code A B C D E F H J K L M N P R S T U V W X A Month January February March April May June July August September October November December Code 1 2 3 4 5 6 7 8 9 O N D © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com F3023_F43 • 3/15/2019 10 Film Capacitors – AC Line EMI Suppression and RC Networks F43 Metallized Polypropylene RC Snubber Film, 160 – 220 VAC/250 – 630 VDC; 275 VAC Class X2 KEMET Electronics Corporation Sales Offices For a complete list of our global sales offi ces, please visit www.kemet.com/sales. Disclaimer All product specifi cations, statements, information and data (collectively, the “Information”) in this datasheet are subject to change. The customer is responsible for checking and verifying the extent to which the Information contained in this publication is applicable to an order at the time the order is placed. All Information given herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied. Statements of suitability for certain applications are based on KEMET Electronics Corporation’s (“KEMET”) knowledge of typical operating conditions for such applications, but are not intended to constitute – and KEMET specifi cally disclaims – any warranty concerning suitability for a specifi c customer application or use. The Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by KEMET with reference to the use of KEMET’s products is given gratis, and KEMET assumes no obligation or liability for the advice given or results obtained. Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. Although all product–related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicted or that other measures may not be required. KEMET is a registered trademark of KEMET Electronics Corporation. © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com F3023_F43 • 3/15/2019 11