F863BK224K310Z

AC Line EMI Suppression and RC Networks Metallized Polypropylene Film EMI Suppression Capacitors for Harsh Environmental Conditions − F863, Class X2, 310 VAC (Automotive Grade) Overview Applications The F863 is constructed of metallized polypropylene film, encapsulated with self−extinguishing resin in a box material recognized by UL 94 V–0. The F863 is ideal for harsh environmental conditions and meets the demanding Automotive Electronics Council's AEC–Q200 qualification requirements. Typical applications include parallel connection and in series with the mains for indoor application, capacitive power supplies with special emphasis in automotive applications for severe ambient conditions. Benefits • Approvals: ENEC, UL, cUL, CQC • Rated voltage: 310 VAC 50/60 Hz • Capacitance range: 0.1 – 10.0 µF • Lead spacing: 15.0 – 37.5 mm • Capacitance tolerance: ±20%, ±10% • Climatic category: 40/110/56, IEC 60068–1 • Tape & Reel in accordance with IEC 60286–2 • RoHS Compliant and lead−free terminations • Operating temperature range of −40°C to +110°C • 100% screening factory test at 1,900 VDC • Qualification based on AEC–Q200 guidelines Simulator Tool and Lifetime Expectancy model available online: K-SIM K-LEM Part Number System F 863 B C 104 M 310 C Capacitor Class Series Lead Spacing (mm) Size Code Capacitance Code (pF) Capacitance Tolerance Voltage (VAC) Packaging F = Film X2, Metallized Polypropylene 310 See Ordering Options Table B = 15 D = 22.5 F = 27.5 R = 37.5 See Dimension Table First two digits represent significant figures. Third digit specifies number of zeros. K = ±10% M = ±20% Built Into Tomorrow © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com F3110_F863_X2_310 • 7/14/2022 1 Film Capacitors – AC Line EMI Suppression and RC Networks Metallized Polypropylene Film EMI Suppression Capacitorsfor Harsh Environmental Conditions F863, Class X2, 310 VAC (Automotive Grade) Ordering Options Table Lead Spacing Nominal (mm) Type of Leads and Packaging Lead Length (mm) Lead and Packaging Code 4 +2/−0 H0 = 18.5 ±0.5 Z R 4 +2/−0 30 +5/−0 H0 = 18.5 ±0.5 H0 = 18.5 ±0.5 C ALW0L L P 4 +2/−0 H0 = 18.5 ±0.5 Z R 4 +2/−0 30 +5/−0 H0 = 18.5 ±0.5 H0 = 18.5 ±0.5 C ALW0L L P 30 +5/−0 ALW0L 4 +2/−0 Z Standard Lead and Packaging Options Pizza Pack Ammo Pack 15 Other Lead and Packaging Options Bulk – Short Leads Bulk – Long Leads Tape & Reel (Standard Reel) Tape & Reel (Large Reel) Standard Lead and Packaging Options 22.5 Pizza Pack 1 Ammo Pack 2 Other Lead and Packaging Options Bulk – Short Leads 3 Bulk – Long Leads Tape & Reel (Standard Reel) Tape & Reel (Large Reel) Standard Lead and Packaging Options 27.5 37.5 Tray – Long Leads Other Lead and Packaging Options Tray – Short Leads 1 Only for dimensions > 7 x16 x 26.5 mm 2 Only for dimensions ≤ 11 x 20 x 26.5 mm 3 Only for dimensions ≤ 7 x 16 x 26.5 mm © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com F3110_F863_X2_310 • 7/14/2022 2 Film Capacitors – AC Line EMI Suppression and RC Networks Metallized Polypropylene Film EMI Suppression Capacitorsfor Harsh Environmental Conditions F863, Class X2, 310 VAC (Automotive Grade) Dimensions – Millimeters FRONT VIEW SIDE VIEW L T H S LL F Size Code S T H L F Nominal Tolerance Nominal Tolerance Nominal Tolerance Nominal Tolerance Nominal Tolerance BC BF BK BN BS BT BW DC DE DL DN DS DV FD FF FJ 15.0 15.0 15.0 15.0 15.0 15.0 15.0 22.5 22.5 22.5 22.5 22.5 22.5 27.5 27.5 27.5 ±0.4 ±0.4 ±0.4 ±0.4 ±0.4 ±0.4 ±0.4 ±0.4 ±0.4 ±0.4 ±0.4 ±0.4 ±0.4 ±0.4 ±0.4 ±0.4 5.0 6.0 7.5 8.5 10.0 9.0 11.0 6.0 7.0 8.5 10.0 11.0 13.0 9.0 11.0 13.0 +0.2/−0.5 +0.2/−0.5 +0.2/−0.5 +0.2/−0.5 +0.2/−0.5 +0.2/−0.5 +0.2/−0.5 +0.2/−0.5 +0.2/−0.5 +0.2/−0.5 +0.2/−0.5 +0.2/−0.5 +0.2/−0.5 +0.2/−0.7 +0.2/−0.7 +0.2/−0.7 11.0 12.0 13.5 14.5 16.0 12.5 19.0 15.0 16.0 17.0 18.5 20.0 22.0 17.0 20.0 22.0 +0.1/−0.5 +0.1/−0.5 +0.1/−0.5 +0.1/−0.5 +0.1/−0.5 +0.1/−0.5 +0.1/−0.5 +0.1/−0.5 +0.1/−0.5 +0.1/−0.5 +0.1/−0.5 +0.1/−0.5 +0.1/−0.5 +0.1/−0.7 +0.1/−0.7 +0.1/−0.7 18.0 18.0 18.0 18.0 18.0 18.0 18.0 26.5 26.5 26.5 26.5 26.5 26.5 32.0 32.0 32.0 +0.3/−0.5 +0.3/−0.5 +0.5/−0.5 +0.5/−0.5 +0.5/−0.5 +0.5/−0.5 +0.5/−0.5 +0.3/−0.5 +0.3/−0.5 +0.3/−0.5 +0.3/−0.5 +0.3/−0.5 +0.3/−0.5 +0.3/−0.7 +0.3/−0.7 +0.3/−0.7 0.6 0.6 0.6 0.6 0.8 0.6 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 FL FP FU FW RE RG RJ RL RQ RR RT 27.5 27.5 27.5 27.5 37.5 37.5 37.5 37.5 37.5 37.5 37.5 ±0.4 ±0.4 ±0.4 ±0.4 ±0.4 ±0.4 ±0.4 ±0.4 ±0.4 ±0.4 ±0.4 13.0 14.0 18.0 22.0 11.0 13.0 16.0 19.0 20.0 24.0 30.0 +0.2/−0.7 +0.2/−0.7 +0.2/−0.7 +0.2/−0.7 +0.3/−0.7 +0.3/−0.7 +0.3/−0.7 +0.3/−0.7 +0.3/−0.7 +0.3/−0.7 +0.3/−0.7 25.0 28.0 33.0 37.0 22.0 24.0 28.5 32.0 40.0 44.0 45.0 +0.1/−0.7 +0.1/−0.7 +0.1/−0.7 +0.1/−0.7 +0.1/−0.7 +0.1/−0.7 +0.1/−0.7 +0.1/−0.7 +0.1/−0.7 +0.1/−0.7 +0.1/−0.7 32.0 32.0 32.0 32.0 41.5 41.5 41.5 41.5 41.5 41.5 41.5 +0.3/−0.7 +0.3/−0.7 +0.3/−0.7 +0.3/−0.7 +0.3/−0.7 +0.3/−0.7 +0.3/−0.7 +0.3/−0.7 +0.3/−0.7 +0.3/−0.7 +0.3/−0.7 0.8 0.8 0.8 0.8 1.0 1.0 1.0 1.0 1.0 1.0 1.0 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 Note: See the Ordering Options Table for lead length (LL/H 0) options. © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com F3110_F863_X2_310 • 7/14/2022 3 Film Capacitors – AC Line EMI Suppression and RC Networks Metallized Polypropylene Film EMI Suppression Capacitorsfor Harsh Environmental Conditions F863, Class X2, 310 VAC (Automotive Grade) Qualification Automotive Grade products meet or exceed the requirements outlined by the Automotive Electronics Council. Details regarding test methods and conditions are referenced in document AEC–Q200, Stress Test Qualification for Passive Components. For additional information regarding the Automotive Electronics Council and AEC–Q200, please visit their website at www.aecouncil.com. Performance Characteristics Rated Voltage Capacitance Range Capacitance Tolerance Temperature Range Climatic Category Storage Conditions Approvals 310 VAC 50/60 Hz 0.1 – 10.0 µF ±20%, ±10% −40°C to +110°C 40/110/56 Storage time: ≤ 24 months from the date marked on the label package Average relative humidity per year ≤ 70% RH ≤ 85% for 30 days randomly distributed throughout the year Dew is absent Temperature: −40 to 80°C (see "Maximum Humidity in Storage Conditions" graph below) ENEC, UL, cUL, CQC Maximum Values at +23°C Dissipation Factor 1 kHz Test Voltage Between Terminals C ≤ 0.1 µF C > 0.1 µF 0.3% 0.2% The 100% screening factory test is carried out at 1,900 VDC. The voltage level is selected to meet the requirements in applicable equipment standards. All electrical characteristics are checked after the test. It is not permitted to repeat this test as there is a risk of damage to the capacitor. KEMET is not liable in such case for any failures. Minimum Values Between Terminals Insulation Resistance In DC Applications C ≤ 0.33 µF ≥ 30,000 MΩ C > 0.33 µF ≥ 10,000 MΩ • µF Recommended voltage ≤ 630 VDC © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com F3110_F863_X2_310 • 7/14/2022 4 Film Capacitors – AC Line EMI Suppression and RC Networks Metallized Polypropylene Film EMI Suppression Capacitorsfor Harsh Environmental Conditions F863, Class X2, 310 VAC (Automotive Grade) Performance Characteristics cont. Maximum Humidity in Storage Condition 100 90 80 70 60 50 40 30 20 10 0 −40 Maximum Irms vs. Th Relative Humidity (%) 120% Maximum Irms 100% 30 Days Annual Average 80% 60% 40% 20% −20 0 20 40 Temperature (°C) 60 80 0% 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 Temperature Th(°C) Maximum Overtemperature ∆Tlim vs Th 25 ∆Tlim (°C) 20 15 10 5 0 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 Temperature Th(°C) Th is the maximum ambient temperature surrounding the capacitor or hottest contact point (e.g. tracks), whichever is higher, in the worst operation conditions in °C. © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com F3110_F863_X2_310 • 7/14/2022 5 Film Capacitors – AC Line EMI Suppression and RC Networks Metallized Polypropylene Film EMI Suppression Capacitorsfor Harsh Environmental Conditions F863, Class X2, 310 VAC (Automotive Grade) Maximum Voltage (Vrms) Versus Frequency (Sinusoidal Waveform/Th ≤ 80°C) Lead Spacing 22.5 mm Lead Spacing 15 mm 100 100 0.1 µF 0.15 µF 0.22 µF 0.33 µF 0.47 µF 0.56 µF 10 1 Voltage (Vrms) 1,000 Voltage (Vrms) 1,000 0.1 0.47 µF 0.68 µF 1 µF 1.5 µF 10 1.0 Frequency (kHz) 10.0 1 100.0 0.1 1.0 Lead Spacing 27.5 mm 100 Voltage (Vrms) 100 Voltage (Vrms) 1,000 1 2.2 µF 3.3 µF 4.7 µF 0.1 Frequency (kHz) 10.0 100.0 4.7 µF 6.8 µF 10 µF 10 1.0 10.0 Lead Spacing 37.5 mm 1,000 10 Frequency (kHz) 100.0 1 0.1 1.0 Frequency (kHz) 10.0 100.0 All the curves are evaluated in accordance to the datasheet declarations and considering an environmental condition as Dry Condition. If your environment is too harsh in terms of temperature and relative humidity, please contact KEMET for any kind of information. © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com F3110_F863_X2_310 • 7/14/2022 6 Film Capacitors – AC Line EMI Suppression and RC Networks Metallized Polypropylene Film EMI Suppression Capacitorsfor Harsh Environmental Conditions F863, Class X2, 310 VAC (Automotive Grade) Maximum Current (Arms) Versus Frequency (Sinusoidal Waveform/Th ≤ 80°C) Lead Spacing 22.5 mm Lead Spacing 15 mm 1 1 Current (Arms) 10 Current (Arms) 10 0.1 µF 0.15 µF 0.22 µF 0.33 µF 0.47 µF 0.56 µF 0.1 0.47 µF 0.68 µF 1 µF 1.5 µF 0.1 0.01 0.01 0.1 1.0 Frequency (kHz) 10.0 0.1 100.0 1.0 Lead Spacing 27.5 mm 1 1 Current (Arms) 10 Current (Arms) 10.0 100.0 Lead Spacing 37.5 mm 10 2.2 µF 3.3 µF 4.7 µF 0.1 Frequency (kHz) 4.7 µF 6.8 µF 10 µF 0.1 0.01 0.01 0.1 1.0 Frequency (kHz) 10.0 100.0 0.1 1.0 Frequency (kHz) 10.0 100.0 All the curves are evaluated in accordance to the datasheet declarations and considering an environmental condition as Dry Condition. If your environment is too harsh in terms of temperature and relative humidity, please contact KEMET for any kind of information. © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com F3110_F863_X2_310 • 7/14/2022 7 Film Capacitors – AC Line EMI Suppression and RC Networks Metallized Polypropylene Film EMI Suppression Capacitorsfor Harsh Environmental Conditions F863, Class X2, 310 VAC (Automotive Grade) Impedance Graph 100 10 Z [Ω] 1 0.1 0.1 µF p. 15 0.01 0.001 0.33 µF p.22.5 1 µF p. 27.5 0.1 1 F [MHz] 10 100 Environmental Test Data Test Publication Procedure Endurance IEC 60384–14 1.25 x VR VAC 50 Hz, once every hour increase to 1,000 VAC for 0.1 second, 1,000 hours at upper rated temperature Vibration IEC 60068–2–6 Test Fc 3 directions at 2 hours each 10 – 55 Hz at 0.75 mm or 98 m/s2 Bump IEC 60068–2–29 Test Eb 1,000 bumps at 390 m/s2 Temperature Cycling JESD22–MethodJA–104 1,000 cycles (−55°C to 85°C) Note: If 100°C or 125°C part the 1,000 cycles will be at that temperature rating. Measurement at 24 ±4 hours after test conclusion. 30 minute maximum dwell time at each temperature extreme. 1 minute maximum transition time. Active Flammability IEC 60384–14 VR +20 surge pulses at 2.5 kV (pulse every 5 seconds) Passive Flammability IEC 60384–14 IEC 60384–1, IEC 60695–11–5 Needle−flame test Biased Humidity MIL–STD–202 Method 103 1,000 hours 40°C/93%RH. Rated Voltage. Measurement at 24 ±2 hours after test conclusion. 85°C, 85% RH and 240 VAC, 500 hours Capacitance change (∆C/C): ≤ 10% Dissipation factor change (∆tan δ): ≤ 5 * 10−3 (at 1 kHz) Insulation resistance Rins or time constant τ = CR Rins: ≥ 50% of initial limit THB Test © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com F3110_F863_X2_310 • 7/14/2022 8 Film Capacitors – AC Line EMI Suppression and RC Networks Metallized Polypropylene Film EMI Suppression Capacitorsfor Harsh Environmental Conditions F863, Class X2, 310 VAC (Automotive Grade) Approvals Certification Body Mark Specification File Number IMQ S.p.A. EN/IEC 60384–14 CA08.00209 UL UL 60384–14 and CAN/CSA–E60384–14 E97797 IEC 60384–14 CQC15001128240 CQC15001128444 CQC15001128445 CQC15001128446 CQC15001128447 CQC Environmental Compliance All new KEMET EMI capacitors are RoHS compliant. Table 1 – Ratings & Part Number Reference Capacitance Value (µF) Size Code 0.1 0.15 0.22 0.33 0.47 0.56 0.47 0.68 1.0 1.5 2.2 3.3 4.7 4.7 6.8 10.0 Capacitance Value (µF) Dimensions in mm Lead Spacing (S) dV/dt (V/µs) Part Number 18.0 18.0 18.0 18.0 18.0 18.0 26.5 26.5 26.5 26.5 32.0 32.0 32.0 41.5 41.5 41.5 15.0 15.0 15.0 15.0 15.0 15.0 22.5 22.5 22.5 22.5 27.5 27.5 27.5 37.5 37.5 37.5 400 400 400 400 400 400 200 200 200 200 150 150 150 100 100 100 F863BC104(1)310(2) F863BF154(1)310(2) F863BK224(1)310(2) F863BN334(1)310(2) F863BW474(1)310(2) F863BW564(1)310(2) F863DE474(1)310(2) F863DN684(1)310(2) F863DS105(1)310(2) F863DV155(1)310(2) F863FL225(1)310(2) F863FU335(1)310(2) F863FW475(1)310(2) F863RL475(1)310(2) F863RR685(1)310(2) F863RT106(1)310(2) L (mm) Lead Spacing (S) dV/dt (V/µs) Part Number T H L BC BF BK BN BW BW DE DN DS DV FL FU FW RL RR RT 5.0 6.0 7.5 8.5 11.0 11.0 7.0 10.0 11.0 13.0 13.0 18.0 22.0 19.0 24.0 30.0 11.0 12.0 13.5 14.5 19.0 19.0 16.0 18.5 20.0 22.0 25.0 33.0 37.0 32.0 44.0 45.0 Size Code T (mm) H (mm) (1) M = ±20%, K = ±10%. (2) Insert lead and packaging code. See Ordering Options Table for available options. © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com F3110_F863_X2_310 • 7/14/2022 9 Film Capacitors – AC Line EMI Suppression and RC Networks Metallized Polypropylene Film EMI Suppression Capacitorsfor Harsh Environmental Conditions F863, Class X2, 310 VAC (Automotive Grade) Soldering Process The implementation of the RoHS directive has resulted in the selection of SnAgCu (SAC) alloys or SnCu alloys as primary solder. This has increased the liquidus temperature from that of 183ºC for SnPb eutectic alloy to 217 – 221°C for the new alloys. As a result, the heat stress to the components, even in wave soldering, has increased considerably due to higher pre−heat and wave temperatures. Polypropylene capacitors are especially sensitive to heat (the melting point of polypropylene is 160 – 170°C). Wave soldering can be destructive, especially for mechanically small polypropylene capacitors (with lead spacing of 5 – 15 mm), and great care has to be taken during soldering. The recommended solder profiles from KEMET should be used. Please consult KEMET with any questions. In general, the wave soldering curve from IEC Publication 61760–1 Edition 2 serves as a solid guideline for successful soldering. Please see Figure 1. Reflow soldering is not recommended for through−hole film capacitors. Exposing capacitors to a soldering profile in excess of the above the recommended limits may result to degradation or permanent damage to the capacitors. Do not place the polypropylene capacitor through an adhesive curing oven to cure resin for surface mount components. Insert through−hole parts after the curing of surface mount parts. Consult KEMET to discuss the actual temperature profile in the oven, if through−hole components must pass through the adhesive curing process. A maximum two soldering cycles is recommended. Please allow time for the capacitor surface temperature to return to a normal temperature before the second soldering cycle. Wave Soldering Recommendations Manual Soldering Recommendations Following is the recommendation for manual soldering with a soldering iron. 300 Second Wave First Wave Recommended Soldering Temperature 200 Temperature (°C) 400 350 Soldering Iron Bit Temperature (°C) 2+3 seconds max 260°C 250 300 250 ∆ T < 150°C Cooling Preheating 150 ca. 2°C/second ca. 3.5°C/second typical ca. 5°C/second Tpreheat 100 Typical 200 50 150 100 0 50 0 40 80 120 160 200 240 Time (seconds) 0 0 1 2 3 4 5 6 7 8 Soldering Time (seconds) The soldering iron tip temperature should be set at 350°C (+10°C maximum), with the soldering duration not to exceed more than 3 seconds. © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com F3110_F863_X2_310 • 7/14/2022 10 Film Capacitors – AC Line EMI Suppression and RC Networks Metallized Polypropylene Film EMI Suppression Capacitorsfor Harsh Environmental Conditions F863, Class X2, 310 VAC (Automotive Grade) Soldering Process cont. Wave Soldering Recommendations cont. 1. The table indicates the maximum set−up temperature of the soldering process Figure 1 Dielectric Film Material Maximum Preheat Temperature Maximum Peak Soldering Temperature Capacitor Capacitor Capacitor Capacitor Pitch Pitch Pitch Pitch ≤ 15 mm > 15 mm ≤ 15 mm > 15 mm Polyester 130°C 130°C 270°C 270°C Polypropylene 110°C 130°C 260°C 270°C Paper 130°C 140°C 270°C 270°C Polyphenylene Sulphide 150°C 160°C 270°C 270°C 2. The maximum temperature measured inside the capacitor: Set the temperature so that inside the element the maximum temperature is below the limit: Dielectric Film Material Maximum Temperature Measured Inside the Element Polyester 160°C Polypropylene 110°C Paper 160°C Polyphenylene Sulphide 160°C Temperature monitored inside the capacitor. Selective Soldering Recommendations Selective dip soldering is a variation of reflow soldering. In this method, the printed circuit board with through−hole components to be soldered is preheated and transported over the solder bath as in normal flow soldering without touching the solder. When the board is over the bath, it is stopped and pre−designed solder pots are lifted from the bath with molten solder only at the places of the selected components, and pressed against the lower surface of the board to solder the components. The temperature profile for selective soldering is similar to the double wave flow soldering outlined in this document, however, instead of two baths, there is only one bath with a time from 3 to 10 seconds. In selective soldering, the risk of overheating is greater than in double wave flow soldering, and great care must be taken so that the parts are not overheated. © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com F3110_F863_X2_310 • 7/14/2022 11 Film Capacitors – AC Line EMI Suppression and RC Networks Metallized Polypropylene Film EMI Suppression Capacitorsfor Harsh Environmental Conditions F863, Class X2, 310 VAC (Automotive Grade) Mounting Resistance to Vibration and Mechanical Shock AEC-Q200 Mechanical Stress Tests: Mechanical Shock Vibration MIL-SDT-202 Method 213 Test condition C Peak value 100 g, duration 6 ms, half-sine-wave (see MIL-HDBK for details) MIL-SDT-202 Method 204 5 g for 20 minutes, 12 cycles each of 3 orientations Use 8"X5" PCB, 0.031" thick. 7 secure points on one 8" side and 2 secure points at corners of opposite sides. Parts mounted within 2" from any secure point. Test from 10 – 2,000 Hz. The capacitors are designed for PCB mounting. The stand-off pipes must be in good contact with the printed circuit board. The capacitors with pitch ≤ 22.5 mm can be mechanically fixed by the leads, for pitch > 22.5 mm, the capacitor body has to be properly fixed (e.g. clamped or glued). Construction Single-sided Metallized Polypropylene Film (First Layer) Molded Plastic Case Detailed Cross Section Molded Plastic Self-Extinguishing Case Resin Single-sided Metallized Polypropylene Film (Second Layer) Margin Margin Metal Contact Layer Metal Contact Layer Margin FILM WINDING SCHEME OPTIONS Leads Single-sided Metallized Polypropylene Film Double-sided Winding Scheme Single-sided Metallized Polypropylene Film 1 Section Single-sided Metallized Polypropylene Film Double-sided Metallized Polyester Carrier Film 2 Sections 1 Section © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com Single-sided Metallized Polyprop Film Diel Single-sided Metallized F3110_F863_X2_310 • 7/14/2022 Double-sided Metallized 12 Polypropy Film Capacitors – AC Line EMI Suppression and RC Networks Metallized Polypropylene Film EMI Suppression Capacitorsfor Harsh Environmental Conditions F863, Class X2, 310 VAC (Automotive Grade) Marking FRONT TOP Approval Marks Rated Voltage Series & Safety Class Manufacturing Plant Code Manufacturer’s Capacitance Logo Manufacturing Date Code IEC Climatic Category Capacitance Tolerance Passive Flammability Category: B for volume ≥ 1750 mm3 C for volume < 1750 mm3 OR FRONT TOP Approval Marks Series & Safety Class Rated Voltage Manufacturing Date Code Manufacturer’s Logo Capacitance IEC Climatic Category Passive Flammability Category: B for volume ≥ 1750 mm3 C for volume < 1750 mm3 Capacitance Tolerance Manufacturing Plant Code © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com F3110_F863_X2_310 • 7/14/2022 13 Film Capacitors – AC Line EMI Suppression and RC Networks Metallized Polypropylene Film EMI Suppression Capacitorsfor Harsh Environmental Conditions F863, Class X2, 310 VAC (Automotive Grade) Manufacturing Date Code (IEC–60062) Y = Year, Z = Month Year 2010 2011 2012 2013 2014 2015 2016 2017 2018 2019 2020 2021 2022 2023 2024 2025 2026 2027 2028 2029 2030 Code A B C D E F H J K L M N P R S T U V W X A Month January February March April May June July August September October November December Code 1 2 3 4 5 6 7 8 9 O N D © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com F3110_F863_X2_310 • 7/14/2022 14 Film Capacitors – AC Line EMI Suppression and RC Networks Metallized Polypropylene Film EMI Suppression Capacitorsfor Harsh Environmental Conditions F863, Class X2, 310 VAC (Automotive Grade) Packaging Quantities Size Code BC BF BK BN BT BS BW DC DE DL DN DS DV FD FF FJ FL FP FU FW RE RG RJ RL RQ RR RT Tray – Pizza Short Leads Tray – Pizza Long Leads Height (mm) Length (mm) Bulk Short Leads Bulk Long Leads 15 5 6 7.5 8.5 9 10 11 11 12 13.5 14.5 12.5 16 19 18 18 18 18 18 18 18 2,000 1,750 1,000 1,000 1,000 750 450 1,000 900 700 500 520 500 350 600 500 350 300 270 15 16 17 18.5 20 22 26.5 26.5 26.5 26.5 26.5 26.5 805 700 22.5 6 7 8.5 10 11 13 500 500 300 300 250 200 300 250 250 160 190 130 27.5 9.0 11.0 13.0 13.0 14.0 18.0 22.0 17.0 20.0 22.0 25.0 28.0 33.0 37.0 32.0 32.0 32.0 32.0 32.0 32.0 32.0 816 560 480 480 352 256 168 408 336 288 288 176 128 112 11.0 13.0 16.0 19.0 20.0 24.0 22.0 24.0 28.5 32.0 40.0 44.0 41.5 41.5 41.5 41.5 41.5 41.5 420 360 216 192 126 108 252 216 108 96 84 72 30.0 45.0 41.5 90 60 Lead Thickness Spacing (mm) 37.5 © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com Standard Large Reel Reel (355 mm) (500 mm) Ammo Pizza 1,250 1,000 800 700 650 600 500 800 680 500 440 410 380 340 1,122 935 748 663 612 561 510 700 550 450 350 350 300 464 380 280 235 217 660 564 468 396 360 300 F3110_F863_X2_310 • 7/14/2022 15 Film Capacitors – AC Line EMI Suppression and RC Networks Metallized Polypropylene Film EMI Suppression Capacitorsfor Harsh Environmental Conditions F863, Class X2, 310 VAC (Automotive Grade) Lead Taping & Packaging (IEC 60286–2) Lead Spacing 5 mm ∆p Lead Spacing 7.5 mm ∆p ∆h H1 W2 F H0 P1 ∆p W0 W1 W W D0 P1 ∆p ∆h t P0 ∆p ∆h H1 W0 W1 P1 ∆p ∆h W2 F H0 D0 P0 Lead Spacing 22.5 – 27.5 mm Lead Spacing 10 – 15 mm H1 ∆h W2 F H0 t ∆p ∆h H1 W0 W1 P0 ∆p ∆h W2 F H0 W0 W1 W D0 P0 P1 ∆h W D0 t t Taping Specification Dimensions in mm Lead Spacing Standard IEC 60286–2 +0.6/−0.1 F 5.0 7.5 10.0 15.0 22.5 27.5 +1/−0.5 W 18.0 18.0 18.0 18.0 18.0 18.0 Minimum W0 6.0 6.0 9.0 10.0 10.0 10.0 Position of Sprocket Hole ±0.5 W1 9.0 9.0 9.0 9.0 9.0 9.0 9+0.75/−0.5 Distance Between Tapes Maximum W2 3.0 3.0 3.0 3.0 3.0 3.0 3.0 Sprocket Hole Diameter ±0.2 D0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 Carrier Tape Width Hold-Down Tape Width 18 12.7 12.7 12.7 12.7 12.7 12.7 12.7 ±0.7 P1 3.85 3.75 7.7 5.2 7.8 5.3 P1 Maximum ∆p 1.3 1.3 1.3 1.3 1.3 1.3 1.3 Lateral Deviation ±2 ∆h 2.0 2.0 2.0 2.0 2.0 2.0 2.0 Total Thickness ±0.2 t 0.7 0.7 0.7 0.7 0.9MAX 0.9MAX 0.9MAX Sprocket Hole/Cap Body ±0.5 H0 18.5 18.5 18.5 18.5 18.5 18.5 18 +2/−0 Feed Hole Lead Spacing Distance Lead – Feed Hole Deviation Tape – Plane ±0.2 (1) P0 F +1/−0.5 (3) (2) ±0.5 ±0.5 ±0.5 ±0.5 ±0.5 ±0.5 (1) Maximum cumulative feed hole error, 1 mm per 20 parts. (2) 16.5 mm available on request. (3) 15 mm available on request (F ≥ 10 mm). © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com F3110_F863_X2_310 • 7/14/2022 16 Film Capacitors – AC Line EMI Suppression and RC Networks Metallized Polypropylene Film EMI Suppression Capacitorsfor Harsh Environmental Conditions F863, Class X2, 310 VAC (Automotive Grade) Lead Taping & Packaging (IEC 60286–2) cont. Ammo Specifications Dimensions (mm) Series R4x, R4x+R, R7x, RSB F5A, F5B, F5D F6xx, F8xx PHExxx, PMExxx, PMRxxx H W T 360 340 59 330 330 50 H T Reel Specifications W Dimensions (mm) Series R4x, R4x+R, R7x, RSB F5A, F5B, F5D F6xx, F8xx PHExxx, PMExxx, PMRxxx D H W 355 500 30 25 55 (Max) 360 500 30 46 (Max) D Manufacturing Date Code (IEC–60062) H W Y = Year, Z = Month Year 2010 2011 2012 2013 2014 2015 2016 2017 2018 2019 2020 2021 2022 2023 2024 2025 2026 2027 2028 2029 2030 Code A B C D E F H J K L M N P R S T U V W X A Month January February March April May June July August September October November December Code 1 2 3 4 5 6 7 8 9 O N D © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com F3110_F863_X2_310 • 7/14/2022 17 Film Capacitors – AC Line EMI Suppression and RC Networks Metallized Polypropylene Film EMI Suppression Capacitorsfor Harsh Environmental Conditions F863, Class X2, 310 VAC (Automotive Grade) KEMET Electronics Corporation Sales Offices For a complete list of our global sales offi ces, please visit www.kemet.com/sales. Disclaimer All product specifi cations, statements, information and data (collectively, the “Information”) in this datasheet are subject to change. The customer is responsible for checking and verifying the extent to which the Information contained in this publication is applicable to an order at the time the order is placed. All Information given herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied. Statements of suitability for certain applications are based on KEMET Electronics Corporation’s (“KEMET”) knowledge of typical operating conditions for such applications, but are not intended to constitute – and KEMET specifi cally disclaims – any warranty concerning suitability for a specifi c customer application or use. The Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by KEMET with reference to the use of KEMET’s products is given gratis, and KEMET assumes no obligation or liability for the advice given or results obtained. Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. Although all product–related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicated or that other measures may not be required. KEMET is a registered trademark of KEMET Electronics Corporation. © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com F3110_F863_X2_310 • 7/14/2022 18