Metallized Polypropylene Film EMI Suppression Capacitors
R41, Class X1/Y2, 300 VAC, 110°C
(Automotive Grade)
Overview
Applications
The R41 is constructed of metallized polypropylene film
encapsulated with self-extinguishing resin in a box of
material meeting the requirements of UL 94 V–0.
For use in electromagnetic interference (EMI) suppression
filter in "line-to-ground" and "across-the-line" applications
requiring Y2/X1 safety classification. Suitable for use in
situations where failure of the capacitor could lead to danger
of electric shock. Not for use in "series with mains" type
applications.
Automotive Grade devices (up to 22.5 mm Lead Spacing)
meet the demanding Automotive Electronics Council's
AEC–Q200 qualification requirements.
Benefits
• Approvals: ENEC, UL, cUL, CQC
• Class X1 / Y2 (IEC 60384-14)
• Rated voltage: 300 VAC 50/60 Hz
• Capacitance range: 0.001 – 1 µF
• Lead spacing: 10 – 37.5 mm
• Capacitance tolerance: ±20%, ±10%
• Climatic category: 40/110/56, IEC 60068–1
• Tape and reel in accordance with IEC 60286–2
• RoHS Compliant and lead-free terminations
• Operating temperature range of −40˚C to +110˚C
• 100% screening factory test at 5,000 VDC/2,500 VAC
• Self-healing properties
• Automotive (AEC–Q200) grades available up to
22.5 mm Lead Spacing
Part Number System
R41
3
I
2330
00
M1
M
Series
Rated Voltage
(VAC)
Lead Spacing
(mm)
Capacitance
Code (pF)
Packaging
Internal Use
Capacitance
Tolerance
See Ordering
Options Table
00
M1
Y2, Metallized
Polypropylene
3 = 300
F = 10.0
I = 15.0
N = 22.5
R = 27.5
W = 37.5
The last three
digits represent
significant figures.
The first digit
specifies number
of zeros to be
added.
K = ±10%
M = ±20%
Built Into Tomorrow
© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
F3100_R41_Y2_300 • 12/3/2021
1
Metallized Polypropylene Film EMI Suppression Capacitors
R41 Series, Class X1/Y2, 300 VAC, 110ºC (Automotive Grade)
Ordering Options Table
Lead Spacing
Nominal
(mm)
Lead Length
(mm)
Lead and
Packaging Code
4 +2/−0
H0= 18.5 ±0.5
00
DQ
Tape & Reel (Large Reel)
H0= 18.5 ±0.5
CK
Bulk (Bag) – Short Leads
3.5 +0.5/−0
JB
Bulk (Bag) – Short Leads
4.0 +0.5/−0
JE
Bulk (Bag) – Short Leads
3.2 +0.3/−0.2
JH
Bulk (Bag) – Long Leads
18 ±1
JM
Bulk (Bag) – Long Leads
30 +5/−0
40
Bulk (Bag) – Long Leads
25 +2/−1
50
4 +2/−0
H0= 18.5 ±0.5
00
CK1
30 +5/−0
25 +2/−1
40
50
4 +2/−0
00
30 +5/−0
25 +2/−1
40
50
Type of Leads and Packaging
Standard Lead and Packaging Options
Bulk (Bag) – Short Leads
Ammo Pack
Other Lead and Packaging Options
10,
15,
22.5
Standard Lead and Packaging Options
27.5
Bulk (Tray) – Short Leads
Tape & Reel (Large Reel)
Other Lead and Packaging Options
Bulk (Tray) – Long Leads
Bulk (Tray) – Long Leads
Standard Lead and Packaging Options
Bulk (Tray) – Short Leads
37.5
Other Lead and Packaging Options
Bulk (Tray) – Long Leads
Bulk (Tray) – Long Leads
1
Not for all sizes, see "Packaging Quantities" table
© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
F3100_R41_Y2_300 • 12/3/2021
2
Metallized Polypropylene Film EMI Suppression Capacitors
R41 Series, Class X1/Y2, 300 VAC, 110ºC (Automotive Grade)
Dimensions – Millimeters
FRONT VIEW
SIDE VIEW
L
T
H
S
LL
F
S
T
H
L
F
Nominal Tolerance Nominal Tolerance Nominal Tolerance Nominal Tolerance Nominal Tolerance
10.0
10.0
10.0
15.0
15.0
15.0
15.0
15.0
22.5
22.5
22.5
22.5
22.5
27.5
27.5
27.5
37.5
37.5
37.5
±0.4
±0.4
±0.4
±0.4
±0.4
±0.4
±0.4
±0.4
±0.4
±0.4
±0.4
±0.4
±0.4
±0.4
±0.4
±0.4
±0.4
±0.4
±0.4
4.0
5.0
6.0
5.0
6.0
7.5
8.5
11.0
6.0
7.0
8.5
10.0
13.0
13.0
14.0
18.0
13.0
16.0
20.0
+0.2/−0.5
+0.2/−0.5
+0.2/−0.5
+0.2/−0.5
+0.2/−0.5
+0.2/−0.5
+0.2/−0.5
+0.2/−0.5
+0.2/−0.5
+0.2/−0.5
+0.2/−0.5
+0.2/−0.5
+0.2/−0.5
+0.2/−0.7
+0.2/−0.7
+0.2/−0.7
+0.2/−0.7
+0.2/−0.7
+0.2/−0.7
9.0
11.0
12.0
11.0
12.0
13.5
14.5
19.0
15.0
16.0
17.0
18.5
22.0
22.0
28.0
33.0
24.0
28.5
40.0
+0.1/−0.5
+0.1/−0.5
+0.1/−0.5
+0.1/−0.5
+0.1/−0.5
+0.1/−0.5
+0.1/−0.5
+0.1/−0.5
+0.1/−0.5
+0.1/−0.5
+0.1/−0.5
+0.1/−0.5
+0.1/−0.5
+0.1/−0.7
+0.1/−0.7
+0.1/−0.7
+0.1/−0.7
+0.1/−0.7
+0.1/−0.7
13.0
13.0
13.0
18.0
18.0
18.0
18.0
18.0
26.5
26.5
26.5
26.5
26.5
32.0
32.0
32.0
41.5
41.5
41.5
+0.3/−0.5
+0.3/−0.5
+0.3/−0.5
+0.3/−0.5
+0.3/−0.5
+0.3/−0.5
+0.3/−0.5
+0.3/−0.5
+0.3/−0.5
+0.3/−0.5
+0.3/−0.5
+0.3/−0.5
+0.3/−0.5
+0.3/−0.7
+0.3/−0.7
+0.3/−0.7
+0.3/−0.7
+0.3/−0.7
+0.3/−0.7
0.6
0.6
0.6
0.6
0.6
0.6
0.6
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1.0
1.0
1.0
±0.05
±0.05
±0.05
±0.05
±0.05
±0.05
±0.05
±0.05
±0.05
±0.05
±0.05
±0.05
±0.05
±0.05
±0.05
±0.05
±0.05
±0.05
±0.05
Note: See Ordering Options Table for lead length (LL/H0) options.
© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
F3100_R41_Y2_300 • 12/3/2021
3
Metallized Polypropylene Film EMI Suppression Capacitors
R41 Series, Class X1/Y2, 300 VAC, 110ºC (Automotive Grade)
Performance Characteristics
Dielectric
Plates
Winding
Leads
Protection
Related documents
Rated Voltage (VR)
Recommended DC Voltage
Polypropylene film
Metal layer deposited by evaporation under vacuum
Non-inductive type
Tinned wire
Plastic case, thermosetting resin filled. Box material is solvent resistant and flame retardant according to UL94.
IEC 60384-14, EN 60384-14
300 VAC (50/60 Hz)
1,000 VDC
Capacitance Range
0.0010 to 1 µF
Capacitance Values
E6 series (IEC 60063)
Capacitance Tolerance
Temperature Range
Climatic Category
±10%, ±20%
−40°C to +110°C
40/110/56 IEC 60068-1
Storage time: ≤ 24 months from the date marked on the label package
Average relative humidity per year ≤ 70%
Storage Conditions
RH ≤ 85% for 30 days randomly distributed throughout the year
Dew is absent
Temperature: −40 to 80°C (see "Maximum Humidity in Storage Conditions" graph below)
Approvals
ENEC, UL, cUL, CQC
Maximum Values at +25°C ±5°C
Dissipation Factor (tanδ)
at 1 kHz
Test Voltage Between Terminals
≤ 0.3% (0.2%*) at 1 kHz , +25°C ±5°C
The 100% screening factory test is carried out at 5,000 VDC/2,500 VAC. The voltage level is selected to meet
the requirements in applicable equipment standards. All electrical characteristics are checked after the test.
It is not permitted to repeat this test as there is a risk to damage the capacitor. KEMET is not liable in such
case for any failures.
Measured at +25°C ±5°C
Insulation Resistance
Minimum Values Between Terminals
Voltage Charge
Voltage Charge Time
C ≤ 0.33 μF
C > 0.33 μF
1 minute
≥ 1 • 10 MΩ
( ≥ 5 • 105 MΩ )*
≥ 30,000 MΩ • µF
( ≥ 150,000 MΩ • µF )*
100 VDC
In DC Applications
5
Recommended voltage ≤ 1,000 VDC
* Typical value
© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
F3100_R41_Y2_300 • 12/3/2021
4
Metallized Polypropylene Film EMI Suppression Capacitors
R41 Series, Class X1/Y2, 300 VAC, 110ºC (Automotive Grade)
Performance Characteristics cont.
Maximum Humidity in Storage Condition
100
90
80
70
60
50
40
30
20
10
0
−40
Maximum Irms vs. Th
Relative Humidity (%)
120%
Maximum Irms
100%
30 Days
Annual Average
80%
60%
40%
20%
−20
0
20
40
60
Temperature (°C)
80
0%
25
35
45
55
65
75
85
95
105
115
Temperature Th(°C)
Maximum Overtemperature ∆Tlim vs Th
25
∆Tlim (°C)
20
15
10
5
120
110
100
Temperature Th(°C)
90
80
70
60
50
40
30
20
10
0
0
Th is the maximum ambient temperature surrounding the capacitor or hottest contact point (e.g. tracks), whichever is higher, in the worst operation
conditions in °C.
© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
F3100_R41_Y2_300 • 12/3/2021
5
Metallized Polypropylene Film EMI Suppression Capacitors
R41 Series, Class X1/Y2, 300 VAC, 110ºC (Automotive Grade)
Maximum Voltage (Vrms) Versus Frequency (Sinusoidal Waveform/Th ≤ 40°C)
Lead Spacing 10 mm
Lead Spacing 15 mm
100
100
0.001 µF
0.068 µF
10
1
Voltage (Vrms)
1,000
Voltage (Vrms)
1,000
0.01 µF
0.047 µF
10
0.1
1.0
Frequency (kHz)
10.0
1
100.0
0.1
1.0
100
Voltage (Vrms)
100
Voltage (Vrms)
1,000
1
0.047 µF
0.1 µF
0.22 µF
0.1
1.0
10.0
100.0
0.22 µF
0.47 µF
0.68 µF
10
Frequency (kHz)
10.0
Lead Spacing 27.5 mm
Lead Spacing 22.5 mm
1,000
10
Frequency (kHz)
100.0
1
0.1
1.0
Frequency (kHz)
10.0
100.0
Lead Spacing 37.5 mm
1,000
Voltage (Vrms)
100
0.47 µF
1 µF
10
1
0.1
1.0
Frequency (kHz)
10.0
100.0
© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
F3100_R41_Y2_300 • 12/3/2021
6
Metallized Polypropylene Film EMI Suppression Capacitors
R41 Series, Class X1/Y2, 300 VAC, 110ºC (Automotive Grade)
Maximum Current (Irms) Versus Frequency (Sinusoidal Waveform/Th ≤ 40°C)
Lead Spacing 15 mm
Lead Spacing 10 mm
1
Current (Arms)
Current (Arms)
1
0.001 µF
0.068 µF
0.1
0.1
0.01 µF
0.047 µF
0.01
0.01
0.1
1.0
Frequency (kHz)
10.0
0.1
100.0
1.0
Frequency (kHz)
10.0
100.0
Lead Spacing 27.5 mm
Lead Spacing 22.5 mm
10
1
0.1
Current (Arms)
Current (Arms)
1
0.047 µF
0.1 µF
0.22 µF
0.22 µF
0.47 µF
0.68 µF
0.1
0.01
0.01
0.1
1.0
Frequency (kHz)
10.0
100.0
0.1
1.0
Frequency (kHz)
10.0
100.0
Lead Spacing 37.5 mm
10
Current (Arms)
1
0.47 µF
1 µF
0.1
0.01
0.1
1.0
Frequency (kHz)
10.0
100.0
© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
F3100_R41_Y2_300 • 12/3/2021
7
Metallized Polypropylene Film EMI Suppression Capacitors
R41 Series, Class X1/Y2, 300 VAC, 110ºC (Automotive Grade)
Qualification
Automotive grade products meet or exceed the requirements outlined by the Automotive Electronics Council. Details
regarding test methods and conditions are referenced in document AEC–Q200, Stress Test Qualification for Passive
Components. For additional information regarding the Automotive Electronics Council and AEC–Q200, please visit their
website at www.aecouncil.com.
Impedance Graph
100
|Z| (Ω)
10
0.001µF
1
0.01 µF
0.1µF
0.1
0.01
0.1
1
10
100
Frequency (MHz)
Environmental Test Data
Test
IEC Publication
Procedure
1.7 x VR VAC 50 Hz, once every hour increase to 1,000 VAC for 0.1
second, 1,000 hours at upper rated temperature
Endurance
EN/IEC 60384–14
Vibration
IEC 60068–2–6 Test Fc
3 directions at 2 hours each 10 – 55 Hz at 0.75 mm or 98 m/s2
Bump
IEC 60068–2–29 Test Eb
1,000 bumps at 390 m/s2
Change of Temperature
IEC 60068–2–14 Test Na
Upper and lower rated temperature 5 cycles
Active Flammability
IEC 60384–14
VR +20 surge pulses at 5 kV (pulse every 5 seconds)
Passive Flammability
IEC 60384–14
IEC 60384–1, IEC 60695–11–5 Needle flame test
Damp Heat Steady State
IEC 60068–2–78 Test Cab
© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
+40°C and 93% RH, 56 days
F3100_R41_Y2_300 • 12/3/2021
8
Metallized Polypropylene Film EMI Suppression Capacitors
R41 Series, Class X1/Y2, 300 VAC, 110ºC (Automotive Grade)
Approvals
Certification Body
Mark
Specification
File Number
IMQ S.p.A.
EN/IEC 60384-14
V4160
UL
UL 60384-14 and
CAN/CSA E60384-14
(300 VAC)
E97797
IEC 60384-14
CQC14001116018
CQC13001101264
CQC15001128704
CQC19001218777
CQC13001087758
CQC
Environmental Compliance
All KEMET EMI capacitors are RoHS Compliant.
© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
F3100_R41_Y2_300 • 12/3/2021
9
Metallized Polypropylene Film EMI Suppression Capacitors
R41 Series, Class X1/Y2, 300 VAC, 110ºC (Automotive Grade)
Table 1 – Ratings & Part Number Reference
Dimensions in mm
Capacitance
Value (µF)
T
H
0.0010
0.0015
0.0022
0.0033
0.0047
0.0068
0.010
0.0033
0.0047
0.0068
0.010
0.015
0.022
0.033
0.047
0.068
0.047
0.068
0.068
0.10
0.15
0.22
0.22
0.33
0.33
0.47
0.68
0.47
0.68
1.0
4.0
4.0
4.0
4.0
5.0
6.0
6.0
5.0
5.0
5.0
5.0
5.0
6.0
7.5
8.5
11.0
6.0
6.0
7.0
8.5
10.0
13.0
13.0
14.0
13.0
18.0
18.0
13.0
16.0
20.0
9.0
9.0
9.0
9.0
11.0
12.0
12.0
11.0
11.0
11.0
11.0
11.0
12.0
13.5
14.5
19.0
15.0
15.0
16.0
17.0
18.5
22.0
22.0
28.0
22.0
33.0
33.0
24.0
28.5
40.0
Capacitance Value (µF)
T (mm)
H (mm)
L
Lead Spacing
(S)
dV/dt
(V/µs)
KEMET
Part Number
Customer
Part Number
13.0
13.0
13.0
13.0
13.0
13.0
13.0
18.0
18.0
18.0
18.0
18.0
18.0
18.0
18.0
18.0
26.5
26.5
26.5
26.5
26.5
26.5
32.0
32.0
32.0
32.0
32.0
41.5
41.5
41.5
10.0
10.0
10.0
10.0
10.0
10.0
10.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
22.5
22.5
22.5
22.5
22.5
22.5
27.5
27.5
27.5
27.5
27.5
37.5
37.5
37.5
800
800
800
800
800
800
800
600
600
600
600
600
600
600
600
600
500
500
500
500
500
500
400
400
400
400
400
300
300
300
413F1100(1)00(2)
413F1150(1)00(2)
413F1220(1)00(2)
413F1330(1)M1(2)
413F1470(1)M1(2)
413F1680(1)00(3)
413F2100(1)M1(3)
413I1330(1)00(2)
413I1470(1)00(2)
413I1680(1)00(2)
413I2100(1)00(2)
413I2150(1)M1(2)
413I2220(1)M1(2)
413I2330(1)M1(2)
413I2470(1)M1(2)
413I2680(1)00(2)
413N2470(1)00(2)
413N2680(1)M1(3)
413N2680(1)00(2)
413N3100(1)M1(2)
413N3150(1)M1(2)
413N3220(1)00(2)
413R3220(1)00(2)
413R3330(1)00(2)
413R3330(1)M1(2)
413R3470(1)00(2)
413R3680(1)00(2)
413W3470(1)00(2)
413W3680(1)00(2)
413W4100(1)00(2)
R413F1100(1)00(2)
R413F1150(1)00(2)
R413F1220(1)00(2)
R413F1330(1)M1(2)
R413F1470(1)M1(2)
R413F1680(1)00(3)
R413F2100(1)M1(3)
R413I1330(1)00(2)
R413I1470(1)00(2)
R413I1680(1)00(2)
R413I2100(1)00(2)
R413I2150(1)M1(2)
R413I2220(1)M1(2)
R413I2330(1)M1(2)
R413I2470(1)M1(2)
R413I2680(1)00(2)
R413N2470(1)00(2)
R413N2680(1)M1(3)
R413N2680(1)00(2)
R413N3100(1)M1(2)
R413N3150(1)M1(2)
R413N3220(1)00(2)
R413R3220(1)00(2)
R413R3330(1)00(2)
R413R3330(1)M1(2)
R413R3470(1)00(2)
R413R3680(1)00(2)
R413W3470(1)00(2)
R413W3680(1)00(2)
R413W4100(1)00(2)
L (mm)
Lead
Spacing (S)
dV/dt (V/µs)
KEMET
Part Number
Customer
Part Number
(1) Insert lead and packaging code. See Ordering Options Table for available options.
(2) M = ±20%, K = ±10%
(3) M = ±20% (only available tolerance).
© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
F3100_R41_Y2_300 • 12/3/2021
10
Metallized Polypropylene Film EMI Suppression Capacitors
R41 Series, Class X1/Y2, 300 VAC, 110ºC (Automotive Grade)
Soldering Process
The implementation of the RoHS directive has resulted in the selection of SnAgCu (SAC) alloys or SnCu alloys as primary solder.
This has increased the liquidus temperature from that of 183°C for SnPb eutectic alloy to 217 – 221°C for the new alloys. As a
result, the heat stress to the components, even in wave soldering, has increased considerably due to higher pre-heat and wave
temperatures. Polypropylene capacitors are especially sensitive to heat (the melting point of polypropylene is 160 – 170°C). Wave
soldering can be destructive, especially for mechanically small polypropylene capacitors (with lead spacing of 5 mm to 15 mm),
and great care has to be taken during soldering. The recommended solder profiles from KEMET should be used. Please consult
KEMET with any questions. In general, the wave soldering curve from IEC Publication 61760-1 Edition 2 serves as a solid guideline
for successful soldering. Please see Figure 1.
Reflow soldering is not recommended for through-hole film capacitors. Exposing capacitors to a soldering profile in excess of the
above the recommended limits may result to degradation or permanent damage to the capacitors.
Do not place the polypropylene capacitor through an adhesive curing oven to cure resin for surface mount components. Insert
through-hole parts after the curing of surface mount parts. Consult KEMET to discuss the actual temperature profile in the oven,
if through-hole components must pass through the adhesive curing process. A maximum two soldering cycles is recommended.
Please allow time for the capacitor surface temperature to return to a normal temperature before the second soldering cycle.
Wave Soldering Recommendations
Manual Soldering Recommendations
The following is the recommendation for
manual soldering with a soldering iron.
300
Second Wave
First Wave
Recommended Soldering Temperature
Temperature (°C)
200
400
350
Soldering Iron Bit Temperature (°C)
2+3 seconds max
260°C
250
300
∆ T < 150°C
Cooling
Preheating
150
ca. 2°C/second
ca. 3.5°C/second typical
ca. 5°C/second
Tpreheat
100
Typical
250
50
200
150
0
100
0
40
80
120
160
200
240
Time (seconds)
50
0
0
1
2
3
4
5
6
7
8
Soldering Time (seconds)
The soldering iron tip temperature should
be set at 350°C (+10°C maximum) with the
soldering duration not to exceed more than 3
seconds.
© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
F3100_R41_Y2_300 • 12/3/2021
11
Metallized Polypropylene Film EMI Suppression Capacitors
R41 Series, Class X1/Y2, 300 VAC, 110ºC (Automotive Grade)
Soldering Process cont.
Wave Soldering Recommendations cont.
1. The table indicates the maximum set-up temperature of the soldering process
Figure 1
Dielectric
Film Material
Maximum
Preheat
Temperature
Maximum
Peak Soldering
Temperature
Capacitor Capacitor Capacitor Capacitor
Pitch
Pitch
Pitch
Pitch
≤ 15 mm > 15 mm ≤ 15 mm > 15 mm
Polyester
130°C
130°C
270°C
270°C
Polypropylene
110°C
130°C
260°C
270°C
Paper
130°C
140°C
270°C
270°C
Polyphenylene
Sulphide
150°C
160°C
270°C
270°C
2. The maximum temperature measured inside the capacitor:
Set the temperature so that inside the element the maximum temperature is below the limit:
Dielectric Film Material
Maximum temperature
measured inside the element
Polyester
160°C
Polypropylene
110°C
Paper
160°C
Polyphenylene
sulphide
160°C
Temperature monitored inside the capacitor.
Selective Soldering Recommendations
Selective dip soldering is a variation of reflow soldering. In this method, the printed circuit board with through-hole
components to be soldered is preheated and transported over the solder bath as in normal flow soldering without touching
the solder. When the board is over the bath, it is stopped and pre-designed solder pots are lifted from the bath with molten
solder only at the places of the selected components, and pressed against the lower surface of the board to solder the
components.
The temperature profile for selective soldering is similar to the double wave flow soldering outlined in this document,
however, instead of two baths, there is only one bath with a time from 3 to 10 seconds. In selective soldering, the risk of
overheating is greater than in double wave flow soldering, and great care must be taken so that the parts are not overheated.
© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
F3100_R41_Y2_300 • 12/3/2021
12
Metallized Polypropylene Film EMI Suppression Capacitors
R41 Series, Class X1/Y2, 300 VAC, 110ºC (Automotive Grade)
Construction
2 Sections
Molded Plastic
Case
Single-sided Metallized
Polypropylene Film
(First Layer)
Detailed Cross Section
Molded Plastic Self-Extinguishing
Case
Resin
Single-sided Metallized
Polypropylene Film
(Second Layer)
Margin
Margin
Metal Contact
Layer
Metal Contact
Layer
FILM WINDINGMargin
SCHEME OPTIONS
Leads
etallized Polypropylene Film
Double-sided Metallized Polyester Film
Winding Scheme
sided
ized
pylene
m
Single-sided
Metallized
Polypropylene
Film
2 Sections
1 Section
2 Sections
sided
ized
pylene
m
Double-sided
Metallized
Polypropylene Polyester Carrier
Film Dielectric
Film
Double-sided
Metallized
Polyester
Carrier
Film
Single-sided
Metallized
Polypropylene
Film
Double-sided
Metallized
Polyester
Carrier
Film
4 Sections
©Metallized
KEMET Electronics
Corporation • KEMET Tower • One East Broward Boulevard
Polyphenylene
Fort Lauderdale,
FL 33301
USA • 954-766-2800 • www.kemet.com
Sulfide Film
(SMR)
Polypropylene
Film Dielectric
Double-sided
Metallized
Polyester Carrier
Film
3 Sections
4 Sections
F3100_R41_Y2_300 • 12/3/2021
Polypropylene Film/Foil
13
Metallized Polypropylene Film EMI Suppression Capacitors
R41 Series, Class X1/Y2, 300 VAC, 110ºC (Automotive Grade)
Marking
Lead Spacing 10 mm
FRONT
TOP
Series,
Dielectric
Code, Safety
Class, Self
Healing
Capacitance,
Rated Voltage
Approval
Marks
Manufacturer’s
Logo
IEC Climatic
Category
Capacitance Tolerance
Date Code
Passive Flammability
Category
Manufacturing
Plant
NOTE: Hot imprinting with or without
color or ink jet or laser marking
Lead Spacing 15 mm, 22.5 mm (small case sizes)
FRONT
TOP
Series,
Dielectric
Code, Safety
Class, Self
Healing
Capacitance,
Rated Voltage
Approval
Marks
Manufacturer’s
Logo
IEC Climatic
Category
Capacitance Tolerance
Date Code
Passive Flammability
Category:
B for volume ≥ 1750 mm3
C for volume < 1750 mm3
Manufacturing
Plant
NOTE: Hot imprinting with or without
color or ink jet or laser marking
* Differences caused by technology (clichee, laser or ink jet) and production line
Lead Spacing 22.5 and 27.5 mm (alternatives*) and 37.5 mm
FRONT
TOP
Series Dielectric
Code
Approval
Marks
Self
Healing
Capacitance,
Capacitance
Tolerance,
Rated Voltage
Manufacturer’s
Logo
IEC Climatic
Category
© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
Safety
Class
QA Number
Passive
Flammability
Category
Manufacturing Date Code
F3100_R41_Y2_300 • 12/3/2021
Plant
14
IEC Climatic
Category
Date Code
Metallized Polypropylene Film EMI Suppression Capacitors
Passive Flammability
R41 Series, Class X1/Y2, 300 VAC, 110ºC
(Automotive Grade)
Category:
B for volume ≥ 1750 mm3
C for volume < 1750 mm3
Manufacturing
Plant
NOTE: Hot imprinting with or without
color or ink jet or laser marking
Marking cont.
Lead Spacing 22.5 and 27.5 mm (alternatives*) and 37.5 mm
FRONT
TOP
Series Dielectric
Code
Safety
Class
Self
Healing
Capacitance,
Capacitance
Tolerance,
Rated Voltage
Manufacturer’s
Logo
Approval
Marks
IEC Climatic
Category
QA Number
Passive
Flammability
Category
Manufacturing
Plant
Date Code
* Differences caused by technology (clichee, laser or ink jet) and production line
Manufacturing Date Code (IEC 60062)
Year
Code
Month
Code
2010
2011
2012
2013
2014
2015
2016
2017
2018
2019
2020
2021
2022
2023
2024
2025
2026
2027
2028
2029
2030
A
B
C
D
E
F
H
J
K
L
M
N
P
R
S
T
U
V
W
X
A
January
February
March
April
May
June
July
August
September
October
November
December
1
2
3
4
5
6
7
8
9
O
N
D
© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
F3100_R41_Y2_300 • 12/3/2021
15
Metallized Polypropylene Film EMI Suppression Capacitors
R41 Series, Class X1/Y2, 300 VAC, 110ºC (Automotive Grade)
Packaging Quantities
Lead Spacing
(mm)
Thickness
(mm)
Height
(mm)
Length
(mm)
Lead And Packaging Code:
Bulk
Short Leads
Bulk
Long Leads
Standard
Reel
ø 355 mm
Large Reel
ø 500 mm
Ammo
Taped
00 - JA - JB
JE - JH
JM - 40 - 50
GY - CK1
CK
DQ
10
4.0
5.0
6.0
9.0
11.0
12.0
13.0
13.0
13.0
2000
1300
1000
1800
1500
1200
750
600
500
1,500
1,250
1,000
1000
800
680
15
5.0
6.0
7.5
8.5
11.0
11.0
12.0
13.5
14.5
19.0
18.0
18.0
18.0
18.0
18.0
2000
1750
1000
1000
450
1000
900
700
500
350
600
500
350
270
270
1,250
1,000
800
700
500
800
680
500
440
340
22.5
6.0
7.0
8.5
10.0
13.0
15.0
16.0
17.0
18.5
22.0
26.5
26.5
26.5
26.5
26.5
805
700
468
396
300
500
500
300
300
200
300
250
250
160
130
700
550
450
350
300
464
380
280
235
–
27.5
13.0
14.0
18.0
22.0
28.0
33.0
32.0
32.0
32.0
480
352
256
288
176
128
–
–
–
300
–
–
–
–
–
37.5
13.0
16.0
20.0
24.0
28.5
40.0
41.5
41.5
41.5
360
216
126
216
108
84
–
–
–
–
–
–
–
–
–
© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
F3100_R41_Y2_300 • 12/3/2021
16
Metallized Polypropylene Film EMI Suppression Capacitors
R41 Series, Class X1/Y2, 300 VAC, 110ºC (Automotive Grade)
Lead Taping & Packaging (IEC 60286–2)
Figure 1
Lead Spacing 10 mm
Figure 2
Lead Spacing 15 mm
Figure 3
Lead Spacing 22.5 – 27.5 mm
P
W2
P2
ød
A
B
W
W0
W1
H0
P1 P0
F
P
h
h
D0
P1
P2
A-B
t
Taping Specification
Dimensions (mm)
Description
Symbol
10
Fig. 1
Lead Space
15
22.5
Fig. 2
Fig. 3
27.5
Fig. 3
Tol.
Lead wire diameter
d
0.6
0.6–0.8
0.8
0.8
±0.05
Taping lead space
P
25.4
25.4
38.1
38.1
±1
Feed hole lead space *
P0
12.7
12.7
12.7
12.7
±0.2 **
Centering of the lead wire
P1
7.7
5.2
7.8
5.3
±0.7
Centering of the body
P2
12.7
12.7
19.05
19.05
±1.3
Lead spacing (pitch) ***
F
10
15
22.5
27.5
+0.6/−0.1
Component alignment
∆h
0
0
0
0
±2
Height of component
from tape center
H 0 ****
18.5
18.5
18.5
18.5
±0.5
Carrier tape width
W
18
18
18
18
+1/−0.5
Hold down tape width
W0
9
10
10
10
Minimum
Hole position
W1
9
9
9
9
±0.5
Hold down tape position
W2
3
3
3
3
Maximum
Feed hole diameter
D0
4
4
4
4
±0.2
Total tape thickness
t
0.7
0.7
0.7
0.7
±0.2
* 15 mm also available
** Maximum of 1 mm on 20 lead spaces
*** Pitches 15 mm and 10 mm taped to 7.5 mm (crimped leads) available upon request
**** H0 = 16.5 mm is available upon request
© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
F3100_R41_Y2_300 • 12/3/2021
17
Metallized Polypropylene Film EMI Suppression Capacitors
R41 Series, Class X1/Y2, 300 VAC, 110ºC (Automotive Grade)
Lead Taping & Packaging (IEC 60286–2) cont.
Ammo Specifications
Dimensions (mm)
H
W
T
360
340
59
H
T
W
Reel Specifications
Reel Size
Standard
Large
Dimensions (mm)
D
H
W
355
500
30
25
55 Maximum
D
H
W
© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
F3100_R41_Y2_300 • 12/3/2021
18
Metallized Polypropylene Film EMI Suppression Capacitors
R41 Series, Class X1/Y2, 300 VAC, 110ºC (Automotive Grade)
KEMET Electronics Corporation Sales Offices
For a complete list of our global sales offi ces, please visit www.kemet.com/sales.
Disclaimer
All product specifi cations, statements, information and data (collectively, the “Information”) in this datasheet are subject to change. The customer is responsible for
checking and verifying the extent to which the Information contained in this publication is applicable to an order at the time the order is placed. All Information given
herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied.
Statements of suitability for certain applications are based on KEMET Electronics Corporation’s (“KEMET”) knowledge of typical operating conditions for such
applications, but are not intended to constitute – and KEMET specifi cally disclaims – any warranty concerning suitability for a specifi c customer application or use.
The Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any
technical advice inferred from this Information or otherwise provided by KEMET with reference to the use of KEMET’s products is given gratis, and KEMET assumes
no obligation or liability for the advice given or results obtained.
Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component
failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards
(such as installation of protective circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury
or property damage.
Although all product–related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicted or that other
measures may not be required.
KEMET is a registered trademark of KEMET Electronics Corporation.
© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
F3100_R41_Y2_300 • 12/3/2021
19