R413F1100DQ00M

Metallized Polypropylene Film EMI Suppression Capacitors R41, Class X1/Y2, 300 VAC, 110°C (Automotive Grade) Overview Applications The R41 is constructed of metallized polypropylene film encapsulated with self-extinguishing resin in a box of material meeting the requirements of UL 94 V–0. For use in electromagnetic interference (EMI) suppression filter in "line-to-ground" and "across-the-line" applications requiring Y2/X1 safety classification. Suitable for use in situations where failure of the capacitor could lead to danger of electric shock. Not for use in "series with mains" type applications. Automotive Grade devices (up to 22.5 mm Lead Spacing) meet the demanding Automotive Electronics Council's AEC–Q200 qualification requirements. Benefits • Approvals: ENEC, UL, cUL, CQC • Class X1 / Y2 (IEC 60384-14) • Rated voltage: 300 VAC 50/60 Hz • Capacitance range: 0.001 – 1 µF • Lead spacing: 10 – 37.5 mm • Capacitance tolerance: ±20%, ±10% • Climatic category: 40/110/56, IEC 60068–1 • Tape and reel in accordance with IEC 60286–2 • RoHS Compliant and lead-free terminations • Operating temperature range of −40˚C to +110˚C • 100% screening factory test at 5,000 VDC/2,500 VAC • Self-healing properties • Automotive (AEC–Q200) grades available up to 22.5 mm Lead Spacing Part Number System R41 3 I 2330 00 M1 M Series Rated Voltage (VAC) Lead Spacing (mm) Capacitance Code (pF) Packaging Internal Use Capacitance Tolerance See Ordering Options Table 00 M1 Y2, Metallized Polypropylene 3 = 300 F = 10.0 I = 15.0 N = 22.5 R = 27.5 W = 37.5 The last three digits represent significant figures. The first digit specifies number of zeros to be added. K = ±10% M = ±20% Built Into Tomorrow © KEMET Electronics Corporation • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com F3100_R41_Y2_300 • 8/15/2023 1 Metallized Polypropylene Film EMI Suppression Capacitors R41 Series, Class X1/Y2, 300 VAC, 110ºC (Automotive Grade) Ordering Options Table Lead Spacing Nominal (mm) Lead Length (mm) Lead and Packaging Code 4 +2/−0 H0= 18.5 ±0.5 00 DQ Tape & Reel (Large Reel) H0= 18.5 ±0.5 CK Bulk (Bag) – Short Leads 3.5 +0.5/−0 JB Bulk (Bag) – Short Leads 4.0 +0.5/−0 JE Bulk (Bag) – Short Leads 3.2 +0.3/−0.2 JH Bulk (Bag) – Long Leads 18 ±1 JM Bulk (Bag) – Long Leads 30 +5/−0 40 Bulk (Bag) – Long Leads 25 +2/−1 50 4 +2/−0 H0= 18.5 ±0.5 00 CK1 30 +5/−0 25 +2/−1 40 50 4 +2/−0 00 30 +5/−0 25 +2/−1 40 50 Type of Leads and Packaging Standard Lead and Packaging Options Bulk (Bag) – Short Leads Ammo Pack Other Lead and Packaging Options 10, 15, 22.5 Standard Lead and Packaging Options 27.5 Bulk (Tray) – Short Leads Tape & Reel (Large Reel) Other Lead and Packaging Options Bulk (Tray) – Long Leads Bulk (Tray) – Long Leads Standard Lead and Packaging Options Bulk (Tray) – Short Leads 37.5 Other Lead and Packaging Options Bulk (Tray) – Long Leads Bulk (Tray) – Long Leads 1 Not for all sizes, see "Packaging Quantities" table © KEMET Electronics Corporation • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com F3100_R41_Y2_300 • 8/15/2023 2 Metallized Polypropylene Film EMI Suppression Capacitors R41 Series, Class X1/Y2, 300 VAC, 110ºC (Automotive Grade) Dimensions – Millimeters FRONT VIEW SIDE VIEW L T H S LL F S T H L F Nominal Tolerance Nominal Tolerance Nominal Tolerance Nominal Tolerance Nominal Tolerance 10.0 10.0 10.0 15.0 15.0 15.0 15.0 15.0 22.5 22.5 22.5 22.5 22.5 27.5 27.5 27.5 37.5 37.5 37.5 ±0.4 ±0.4 ±0.4 ±0.4 ±0.4 ±0.4 ±0.4 ±0.4 ±0.4 ±0.4 ±0.4 ±0.4 ±0.4 ±0.4 ±0.4 ±0.4 ±0.4 ±0.4 ±0.4 4.0 5.0 6.0 5.0 6.0 7.5 8.5 11.0 6.0 7.0 8.5 10.0 13.0 13.0 14.0 18.0 13.0 16.0 20.0 +0.2/−0.5 +0.2/−0.5 +0.2/−0.5 +0.2/−0.5 +0.2/−0.5 +0.2/−0.5 +0.2/−0.5 +0.2/−0.5 +0.2/−0.5 +0.2/−0.5 +0.2/−0.5 +0.2/−0.5 +0.2/−0.5 +0.2/−0.7 +0.2/−0.7 +0.2/−0.7 +0.2/−0.7 +0.2/−0.7 +0.2/−0.7 9.0 11.0 12.0 11.0 12.0 13.5 14.5 19.0 15.0 16.0 17.0 18.5 22.0 22.0 28.0 33.0 24.0 28.5 40.0 +0.1/−0.5 +0.1/−0.5 +0.1/−0.5 +0.1/−0.5 +0.1/−0.5 +0.1/−0.5 +0.1/−0.5 +0.1/−0.5 +0.1/−0.5 +0.1/−0.5 +0.1/−0.5 +0.1/−0.5 +0.1/−0.5 +0.1/−0.7 +0.1/−0.7 +0.1/−0.7 +0.1/−0.7 +0.1/−0.7 +0.1/−0.7 13.0 13.0 13.0 18.0 18.0 18.0 18.0 18.0 26.5 26.5 26.5 26.5 26.5 32.0 32.0 32.0 41.5 41.5 41.5 +0.3/−0.5 +0.3/−0.5 +0.3/−0.5 +0.3/−0.5 +0.3/−0.5 +0.3/−0.5 +0.3/−0.5 +0.3/−0.5 +0.3/−0.5 +0.3/−0.5 +0.3/−0.5 +0.3/−0.5 +0.3/−0.5 +0.3/−0.7 +0.3/−0.7 +0.3/−0.7 +0.3/−0.7 +0.3/−0.7 +0.3/−0.7 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 1.0 1.0 1.0 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 ±0.05 Note: See Ordering Options Table for lead length (LL/H0) options. © KEMET Electronics Corporation • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com F3100_R41_Y2_300 • 8/15/2023 3 Metallized Polypropylene Film EMI Suppression Capacitors R41 Series, Class X1/Y2, 300 VAC, 110ºC (Automotive Grade) Performance Characteristics Dielectric Plates Winding Leads Protection Related documents Rated Voltage (VR) Recommended DC Voltage Polypropylene film Metal layer deposited by evaporation under vacuum Non-inductive type Tinned wire Plastic case, thermosetting resin filled. Box material is solvent resistant and flame retardant according to UL94. IEC 60384-14, EN 60384-14 300 VAC (50/60 Hz) 1,000 VDC Capacitance Range 0.0010 to 1 µF Capacitance Values E6 series (IEC 60063) Capacitance Tolerance Temperature Range Climatic Category ±10%, ±20% −40°C to +110°C 40/110/56 IEC 60068-1 Storage time: ≤ 24 months from the date marked on the label package Average relative humidity per year ≤ 70% Storage Conditions RH ≤ 85% for 30 days randomly distributed throughout the year Dew is absent Temperature: −40 to 80°C (see "Maximum Humidity in Storage Conditions" graph below) Approvals ENEC, UL, cUL, CQC Maximum Values at +25°C ±5°C Dissipation Factor (tanδ) at 1 kHz Test Voltage Between Terminals ≤ 0.3% (0.2%*) at 1 kHz , +25°C ±5°C The 100% screening factory test is carried out at 5,000 VDC/2,500 VAC. The voltage level is selected to meet the requirements in applicable equipment standards. All electrical characteristics are checked after the test. It is not permitted to repeat this test as there is a risk to damage the capacitor. KEMET is not liable in such case for any failures. Measured at +25°C ±5°C Insulation Resistance Minimum Values Between Terminals Voltage Charge 100 VDC In DC Applications Voltage Charge Time C ≤ 0.33 μF C > 0.33 μF 1 minute ≥ 1 • 10 MΩ ( ≥ 5 • 105 MΩ )* ≥ 30,000 MΩ • µF ( ≥ 150,000 MΩ • µF )* 5 Recommended voltage ≤ 1,000 VDC * Typical value © KEMET Electronics Corporation • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com F3100_R41_Y2_300 • 8/15/2023 4 Metallized Polypropylene Film EMI Suppression Capacitors R41 Series, Class X1/Y2, 300 VAC, 110ºC (Automotive Grade) Performance Characteristics cont. Maximum Humidity in Storage Condition 100 90 80 70 60 50 40 30 20 10 0 −40 Maximum Irms vs. Th Relative Humidity (%) 120% Maximum Irms 100% 30 Days Annual Average 80% 60% 40% 20% −20 0 20 40 60 Temperature (°C) 80 0% 25 35 45 55 65 75 85 95 105 115 Temperature Th(°C) Maximum Overtemperature ∆Tlim vs Th 25 ∆Tlim (°C) 20 15 10 5 120 110 100 Temperature Th(°C) 90 80 70 60 50 40 30 20 10 0 0 Th is the maximum ambient temperature surrounding the capacitor or hottest contact point (e.g. tracks), whichever is higher, in the worst operation conditions in °C. © KEMET Electronics Corporation • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com F3100_R41_Y2_300 • 8/15/2023 5 Metallized Polypropylene Film EMI Suppression Capacitors R41 Series, Class X1/Y2, 300 VAC, 110ºC (Automotive Grade) Maximum Voltage (Vrms) Versus Frequency (Sinusoidal Waveform/Th ≤ 40°C) Lead Spacing 10 mm Lead Spacing 15 mm 100 100 0.001 µF 0.068 µF 10 1 Voltage (Vrms) 1,000 Voltage (Vrms) 1,000 0.01 µF 0.047 µF 10 0.1 1.0 Frequency (kHz) 10.0 1 100.0 0.1 1.0 100 Voltage (Vrms) 100 Voltage (Vrms) 1,000 1 0.047 µF 0.1 µF 0.22 µF 0.1 1.0 10.0 100.0 0.22 µF 0.47 µF 0.68 µF 10 Frequency (kHz) 10.0 Lead Spacing 27.5 mm Lead Spacing 22.5 mm 1,000 10 Frequency (kHz) 100.0 1 0.1 1.0 Frequency (kHz) 10.0 100.0 Lead Spacing 37.5 mm 1,000 Voltage (Vrms) 100 0.47 µF 1 µF 10 1 0.1 1.0 Frequency (kHz) 10.0 © KEMET Electronics Corporation • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com 100.0 F3100_R41_Y2_300 • 8/15/2023 6 Metallized Polypropylene Film EMI Suppression Capacitors R41 Series, Class X1/Y2, 300 VAC, 110ºC (Automotive Grade) Maximum Current (Irms) Versus Frequency (Sinusoidal Waveform/Th ≤ 40°C) Lead Spacing 15 mm Lead Spacing 10 mm 1 Current (Arms) Current (Arms) 1 0.001 µF 0.068 µF 0.1 0.1 0.01 µF 0.047 µF 0.01 0.01 0.1 1.0 Frequency (kHz) 10.0 0.1 100.0 1.0 Frequency (kHz) 10.0 100.0 Lead Spacing 27.5 mm Lead Spacing 22.5 mm 10 1 0.1 Current (Arms) Current (Arms) 1 0.047 µF 0.1 µF 0.22 µF 0.22 µF 0.47 µF 0.68 µF 0.1 0.01 0.01 0.1 1.0 Frequency (kHz) 10.0 100.0 0.1 1.0 Frequency (kHz) 10.0 100.0 Lead Spacing 37.5 mm 10 Current (Arms) 1 0.47 µF 1 µF 0.1 0.01 0.1 1.0 Frequency (kHz) 10.0 © KEMET Electronics Corporation • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com 100.0 F3100_R41_Y2_300 • 8/15/2023 7 Metallized Polypropylene Film EMI Suppression Capacitors R41 Series, Class X1/Y2, 300 VAC, 110ºC (Automotive Grade) Qualification Automotive grade products meet or exceed the requirements outlined by the Automotive Electronics Council. Details regarding test methods and conditions are referenced in document AEC–Q200, Stress Test Qualification for Passive Components. For additional information regarding the Automotive Electronics Council and AEC–Q200, please visit their website at www.aecouncil.com. Impedance Graph 100 |Z| (Ω) 10 0.001µF 1 0.01 µF 0.1µF 0.1 0.01 0.1 1 10 100 Frequency (MHz) Environmental Test Data Test IEC Publication Procedure 1.7 x VR VAC 50 Hz, once every hour increase to 1,000 VAC for 0.1 second, 1,000 hours at upper rated temperature Endurance EN/IEC 60384–14 Vibration IEC 60068–2–6 Test Fc 3 directions at 2 hours each 10 – 55 Hz at 0.75 mm or 98 m/s2 Bump IEC 60068–2–29 Test Eb 1,000 bumps at 390 m/s2 Change of Temperature IEC 60068–2–14 Test Na Upper and lower rated temperature 5 cycles Active Flammability IEC 60384–14 VR +20 surge pulses at 5 kV (pulse every 5 seconds) Passive Flammability IEC 60384–14 IEC 60384–1, IEC 60695–11–5 Needle flame test Damp Heat Steady State IEC 60068–2–78 Test Cab © KEMET Electronics Corporation • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com +40°C and 93% RH, 56 days F3100_R41_Y2_300 • 8/15/2023 8 Metallized Polypropylene Film EMI Suppression Capacitors R41 Series, Class X1/Y2, 300 VAC, 110ºC (Automotive Grade) Approvals Certification Body Mark Specification File Number IMQ S.p.A. EN/IEC 60384-14 V4160 UL UL 60384-14 and CAN/CSA E60384-14 (300 VAC) E97797 IEC 60384-14 CQC13001101264 CQC15001128704 CQC19001218777 CQC13001087758 CQC Environmental Compliance All KEMET EMI capacitors are RoHS Compliant. © KEMET Electronics Corporation • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com F3100_R41_Y2_300 • 8/15/2023 9 Metallized Polypropylene Film EMI Suppression Capacitors R41 Series, Class X1/Y2, 300 VAC, 110ºC (Automotive Grade) Table 1 – Ratings & Part Number Reference Dimensions in mm Capacitance Value (µF) T H 0.0010 0.0015 0.0022 0.0033 0.0047 0.0068 0.010 0.0033 0.0047 0.0068 0.010 0.015 0.022 0.033 0.047 0.068 0.047 0.068 0.068 0.10 0.15 0.22 0.22 0.33 0.33 0.47  0.68 0.47 0.68 1.0 4.0 4.0 4.0 4.0 5.0 6.0 6.0 5.0 5.0 5.0 5.0 5.0 6.0 7.5 8.5 11.0 6.0 6.0 7.0 8.5 10.0 13.0 13.0 14.0 13.0 18.0 18.0 13.0 16.0 20.0 9.0 9.0 9.0 9.0 11.0 12.0 12.0 11.0 11.0 11.0 11.0 11.0 12.0 13.5 14.5 19.0 15.0 15.0 16.0 17.0 18.5 22.0 22.0 28.0 22.0 33.0 33.0 24.0 28.5 40.0 Capacitance Value (µF) T (mm) H (mm) L Lead Spacing (S) dV/dt (V/µs) KEMET Part Number Customer Part Number 13.0 13.0 13.0 13.0 13.0 13.0 13.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 26.5 26.5 26.5 26.5 26.5 26.5 32.0 32.0 32.0 32.0 32.0 41.5 41.5 41.5 10.0 10.0 10.0 10.0 10.0 10.0 10.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 22.5 22.5 22.5 22.5 22.5 22.5 27.5 27.5 27.5 27.5 27.5 37.5 37.5 37.5 800 800 800 800 800 800 800 600 600 600 600 600 600 600 600 600 500 500 500 500 500 500 400 400 400 400 400 300 300 300 413F1100(1)00(2) 413F1150(1)00(2) 413F1220(1)00(2) 413F1330(1)M1(2) 413F1470(1)M1(2) 413F1680(1)00(3) 413F2100(1)M1(3) 413I1330(1)00(2) 413I1470(1)00(2) 413I1680(1)00(2) 413I2100(1)00(2) 413I2150(1)M1(2) 413I2220(1)M1(2) 413I2330(1)M1(2) 413I2470(1)M1(2) 413I2680(1)00(2) 413N2470(1)00(2) 413N2680(1)M1(3) 413N2680(1)00(2) 413N3100(1)M1(2) 413N3150(1)M1(2) 413N3220(1)00(2) 413R3220(1)00(2) 413R3330(1)00(2) 413R3330(1)M1(2) 413R3470(1)00(2) 413R3680(1)00(2) 413W3470(1)00(2) 413W3680(1)00(2) 413W4100(1)00(2) R413F1100(1)00(2) R413F1150(1)00(2) R413F1220(1)00(2) R413F1330(1)M1(2) R413F1470(1)M1(2) R413F1680(1)00(3) R413F2100(1)M1(3) R413I1330(1)00(2) R413I1470(1)00(2) R413I1680(1)00(2) R413I2100(1)00(2) R413I2150(1)M1(2) R413I2220(1)M1(2) R413I2330(1)M1(2) R413I2470(1)M1(2) R413I2680(1)00(2) R413N2470(1)00(2) R413N2680(1)M1(3) R413N2680(1)00(2) R413N3100(1)M1(2) R413N3150(1)M1(2) R413N3220(1)00(2) R413R3220(1)00(2) R413R3330(1)00(2) R413R3330(1)M1(2) R413R3470(1)00(2) R413R3680(1)00(2) R413W3470(1)00(2) R413W3680(1)00(2) R413W4100(1)00(2) L (mm) Lead Spacing (S) dV/dt (V/µs) KEMET Part Number Customer Part Number (1) Insert lead and packaging code. See Ordering Options Table for available options. (2) M = ±20%, K = ±10% (3) M = ±20% (only available tolerance). © KEMET Electronics Corporation • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com F3100_R41_Y2_300 • 8/15/2023 10 Metallized Polypropylene Film EMI Suppression Capacitors R41 Series, Class X1/Y2, 300 VAC, 110ºC (Automotive Grade) Soldering Process The implementation of the RoHS directive has resulted in the selection of SnAgCu (SAC) alloys or SnCu alloys as primary solder. This has increased the liquidus temperature from that of 183°C for SnPb eutectic alloy to 217 – 221°C for the new alloys. As a result, the heat stress to the components, even in wave soldering, has increased considerably due to higher pre-heat and wave temperatures. Polypropylene capacitors are especially sensitive to heat (the melting point of polypropylene is 160 – 170°C). Wave soldering can be destructive, especially for mechanically small polypropylene capacitors (with lead spacing of 5 mm to 15 mm), and great care has to be taken during soldering. The recommended solder profiles from KEMET should be used. Please consult KEMET with any questions. In general, the wave soldering curve from IEC Publication 61760-1 Edition 2 serves as a solid guideline for successful soldering. Please see Figure 1. Reflow soldering is not recommended for through-hole film capacitors. Exposing capacitors to a soldering profile in excess of the above the recommended limits may result to degradation or permanent damage to the capacitors. Do not place the polypropylene capacitor through an adhesive curing oven to cure resin for surface mount components. Insert through-hole parts after the curing of surface mount parts. Consult KEMET to discuss the actual temperature profile in the oven, if through-hole components must pass through the adhesive curing process. A maximum two soldering cycles is recommended. Please allow time for the capacitor surface temperature to return to a normal temperature before the second soldering cycle. Wave Soldering Recommendations Manual Soldering Recommendations The following is the recommendation for manual soldering with a soldering iron. 300 Second Wave First Wave Recommended Soldering Temperature Temperature (°C) 200 400 350 Soldering Iron Bit Temperature (°C) 2+3 seconds max 260°C 250 300 ∆ T < 150°C Cooling Preheating 150 ca. 2°C/second ca. 3.5°C/second typical ca. 5°C/second Tpreheat 100 Typical 250 50 200 150 0 100 0 40 80 120 160 200 240 Time (seconds) 50 0 0 1 2 3 4 5 6 7 8 Soldering Time (seconds) The soldering iron tip temperature should be set at 350°C (+10°C maximum) with the soldering duration not to exceed more than 3 seconds. © KEMET Electronics Corporation • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com F3100_R41_Y2_300 • 8/15/2023 11 Metallized Polypropylene Film EMI Suppression Capacitors R41 Series, Class X1/Y2, 300 VAC, 110ºC (Automotive Grade) Soldering Process cont. Wave Soldering Recommendations cont. 1. The table indicates the maximum set-up temperature of the soldering process Figure 1 Dielectric Film Material Maximum Preheat Temperature Maximum Peak Soldering Temperature Capacitor Capacitor Capacitor Capacitor Pitch Pitch Pitch Pitch ≤ 15 mm > 15 mm ≤ 15 mm > 15 mm Polyester 130°C 130°C 270°C 270°C Polypropylene 110°C 130°C 260°C 270°C Paper 130°C 140°C 270°C 270°C Polyphenylene Sulphide 150°C 160°C 270°C 270°C 2. The maximum temperature measured inside the capacitor: Set the temperature so that inside the element the maximum temperature is below the limit: Dielectric Film Material Maximum temperature measured inside the element Polyester 160°C Polypropylene 110°C Paper 160°C Polyphenylene sulphide 160°C Temperature monitored inside the capacitor. Selective Soldering Recommendations Selective dip soldering is a variation of reflow soldering. In this method, the printed circuit board with through-hole components to be soldered is preheated and transported over the solder bath as in normal flow soldering without touching the solder. When the board is over the bath, it is stopped and pre-designed solder pots are lifted from the bath with molten solder only at the places of the selected components, and pressed against the lower surface of the board to solder the components. The temperature profile for selective soldering is similar to the double wave flow soldering outlined in this document, however, instead of two baths, there is only one bath with a time from 3 to 10 seconds. In selective soldering, the risk of overheating is greater than in double wave flow soldering, and great care must be taken so that the parts are not overheated. © KEMET Electronics Corporation • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com F3100_R41_Y2_300 • 8/15/2023 12 Metallized Polypropylene Film EMI Suppression Capacitors R41 Series, Class X1/Y2, 300 VAC, 110ºC (Automotive Grade) Mounting Resistance to Vibration and Mechanical Shock AEC-Q200 Rev. E Mechanical Stress Tests: Figure 1 of Method 213 Mechanical Shock • THT: Condition C • SMD: Condition C • Tested per the Supplier’s recommended mounting method MIL-STD-202 Method 213 • 5 g for 20 minutes, 12 cycles each of 3 orientations • Tested per the Supplier’s recommended mounting method • Verification of transfer load: during setup, verify that with the Vibration selected PCB design (size, thickness and secure points), or an alternative mount, that the transferred load onto the component corresponds to the requested load. This verification can be achieved using a laser vibrometer or other adequate measuring device MIL-STD-202 Method 204 • Test from 10 Hz – 2,000 Hz. The capacitors are designed for PCB mounting. The stand-off pipes must be in good contact with the printed circuit board. The capacitor body has to be properly fixed (e.g. clamped or glued). Construction 2 Sections Molded Plastic Case Single-sided Metallized Polypropylene Film (First Layer) Single-sided Metallized Polypropylene Film (Second Layer) Margin Margin Metal Contact Layer Metal Contact Layer FILM WINDINGMargin SCHEME OPTIONS Leads Metallized Polypropylene Film Double-sided Metallized Polyester Film Winding Scheme e-sided allized ropylene Film e-sided allized Detailed Cross Section Molded Plastic Self-Extinguishing Case Resin Single-sided Metallized Polypropylene Film Double-sided Metallized Polyester Carrier Film 2 Sections © KEMET Electronics Corporation • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com Double-sided Metallized Single-sided Metallized Polypropylene Film 2 Sections 1 Section Single-sided Metallized Polypropylene Film Dielectric Double-sided Metallized Polypropylene Polyester Carrier Film Dielectric Film F3100_R41_Y2_300 • 8/15/2023 Polypropylene Film Dielectric Double-sided Metallized Polyester Carrier Film Polypropylene Film Dielectric 13 Metallized Polypropylene Film EMI Suppression Capacitors R41 Series, Class X1/Y2, 300 VAC, 110ºC (Automotive Grade) Marking Lead Spacing 10 mm FRONT TOP Series, Dielectric Code, Safety Class, Self Healing Capacitance, Rated Voltage Approval Marks Manufacturer’s Logo IEC Climatic Category Capacitance Tolerance Date Code Passive Flammability Category Manufacturing Plant NOTE: Hot imprinting with or without color or ink jet or laser marking Lead Spacing 15 mm, 22.5 mm (small case sizes) FRONT TOP Series, Dielectric Code, Safety Class, Self Healing Capacitance, Rated Voltage Approval Marks Manufacturer’s Logo IEC Climatic Category Capacitance Tolerance Date Code Passive Flammability Category: B for volume ≥ 1750 mm3 C for volume < 1750 mm3 Manufacturing Plant NOTE: Hot imprinting with or without color or ink jet or laser marking * Differences caused by technology (clichee, laser or ink jet) and production line Lead Spacing 22.5 and 27.5 mm (alternatives*) and 37.5 mm Slight change in the layout can be possible but this does not affect the content of the information of the current marking. FRONT This change will be achieved without impact to product form, fit or function, as the products are equivalent withTOP respect to physical, mechanical, quality Series Dielectric Safety Self and reliability characteristics. Code Class Healing Approval Marks Capacitance, Capacitance Tolerance, Rated Voltage Manufacturer’s Logo IEC Climatic Category © KEMET Electronics Corporation • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com QA Number Passive Flammability Category Manufacturing Date Code F3100_R41_Y2_300 • 8/15/2023 Plant 14 IEC Climatic Category Date Code Metallized Polypropylene Film EMI Suppression Capacitors Passive Flammability R41 Series, Class X1/Y2, 300 VAC, 110ºC (Automotive Grade) Category: B for volume ≥ 1750 mm3 C for volume < 1750 mm3 Manufacturing Plant NOTE: Hot imprinting with or without color or ink jet or laser marking Marking cont. Lead Spacing 22.5 and 27.5 mm (alternatives*) and 37.5 mm FRONT TOP Series Dielectric Code Safety Class Self Healing Capacitance, Capacitance Tolerance, Rated Voltage Manufacturer’s Logo Approval Marks IEC Climatic Category QA Number Passive Flammability Category Manufacturing Plant Date Code * Differences caused by technology (clichee, laser or ink jet) and production line Slight change in the layout can be possible but this does not affect the content of the information of the current marking. This change will be achieved without impact to product form, fit or function, as the products are equivalent with respect to physical, mechanical, quality and reliability characteristics. Manufacturing Date Code (IEC 60062) Year Code Year Code Year Code Month Code Month Code 2020 2021 2022 2023 2024 2025 2026 M N P R S T U 2027 2028 2029 2030 2031 2032 2033 V W X A B C D 2034 2035 2036 2037 2038 2039 2040 E F G H K L M January February March April May June 1 2 3 4 5 6 July August September October November December 7 8 9 O N D © KEMET Electronics Corporation • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com F3100_R41_Y2_300 • 8/15/2023 15 Metallized Polypropylene Film EMI Suppression Capacitors R41 Series, Class X1/Y2, 300 VAC, 110ºC (Automotive Grade) Packaging Quantities Lead Spacing (mm) Thickness (mm) Height (mm) Length (mm) 00 - JB JE - JH Lead And Packaging Code: 10 15 22.5 27.5 37.5 Bulk Short Leads Bulk Long Leads 40 - 50 JM Standard Reel ø 355 mm Large Reel ø 500 mm Ammo Taped GY CK DQ 4.0 9.0 13.0 2,000 1,800 2,200 750 1,500 1000 5.0 11.0 13.0 1,300 1,500 2,000 600 1,250 800 6.0 12.0 13.0 1,000 1,200 1,800 500 1,000 680 5.0 11.0 18.0 2,000 1,000 1,250 600 1,250 800 6.0 12.0 18.0 1,750 900 1,000 500 1,000 680 7.5 13.5 18.0 1,000 700 800 350 800 500 8.5 14.5 18.0 1,000 500 650 270 700 440 11.0 19.0 18.0 450 350 400 270 500 340 6.0 15.0 26.5 805 500 450 300 700 464 7.0 16.0 26.5 700 500 450 250 550 380 8.5 17.0 26.5 468 300 350 250 450 280 10.0 18.5 26.5 396 300 350 160 350 235 13.0 22.0 26.5 300 200 150 130 300 – 13.0 22.0 32.0 480 288 288 – 300 – 14.0 28.0 32.0 352 176 176 – – – 18.0 33.0 32.0 256 128 128 – – – 13.0 24.0 41.5 360 216 216 – – – 16.0 28.5 41.5 216 108 108 – – – 20.0 40.0 41.5 126 84 84 – – – © KEMET Electronics Corporation • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com F3100_R41_Y2_300 • 8/15/2023 16 Metallized Polypropylene Film EMI Suppression Capacitors R41 Series, Class X1/Y2, 300 VAC, 110ºC (Automotive Grade) Lead Taping & Packaging (IEC 60286–2) Figure 1 Lead Spacing 10 mm Figure 2 Lead Spacing 15 mm Figure 3 Lead Spacing 22.5 – 27.5 mm P W2 P2 ød A B W W0 W1 H0 P1 P0 F P h h D0 P1 P2 A-B t Taping Specification Dimensions (mm) Description Symbol 10 Fig. 1 Lead Space 15 22.5 Fig. 2 Fig. 3 27.5 Fig. 3 Tol. Lead wire diameter d 0.6 0.6–0.8 0.8 0.8 ±0.05 Taping lead space P 25.4 25.4 38.1 38.1 ±1 Feed hole lead space * P0 12.7 12.7 12.7 12.7 ±0.2 ** Centering of the lead wire P1 7.7 5.2 7.8 5.3 ±0.7 Centering of the body P2 12.7 12.7 19.05 19.05 ±1.3 Lead spacing (pitch) *** F 10 15 22.5 27.5 +0.6/−0.1 Component alignment ∆h 0 0 0 0 ±2 Height of component from tape center H 0 **** 18.5 18.5 18.5 18.5 ±0.5 Carrier tape width W 18 18 18 18 +1/−0.5 Hold down tape width W0 9 10 10 10 Minimum Hole position W1 9 9 9 9 ±0.5 Hold down tape position W2 3 3 3 3 Maximum Feed hole diameter D0 4 4 4 4 ±0.2 Total tape thickness t 0.7 0.7 0.7 0.7 ±0.2 * 15 mm also available ** Maximum of 1 mm on 20 lead spaces *** Pitches 15 mm and 10 mm taped to 7.5 mm (crimped leads) available upon request **** H0 = 16.5 mm is available upon request © KEMET Electronics Corporation • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com F3100_R41_Y2_300 • 8/15/2023 17 Metallized Polypropylene Film EMI Suppression Capacitors R41 Series, Class X1/Y2, 300 VAC, 110ºC (Automotive Grade) Lead Taping & Packaging (IEC 60286–2) cont. Ammo Specifications Dimensions (mm) H W T 360 340 59 H T W Reel Specifications Reel Size Standard Large Dimensions (mm) D H W 355 500 30 25 55 Maximum D H W © KEMET Electronics Corporation • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com F3100_R41_Y2_300 • 8/15/2023 18 Metallized Polypropylene Film EMI Suppression Capacitors R41 Series, Class X1/Y2, 300 VAC, 110ºC (Automotive Grade) KEMET Electronics Corporation Sales Offices For a complete list of our global sales offi ces, please visit www.kemet.com/sales. Disclaimer YAGEO Corporation and its affi liates do not recommend the use of commercial or automotive grade products for high reliability applications or manned space fl ight. All product specifi cations, statements, information and data (collectively, the “Information”) in this datasheet are subject to change. The customer is responsible for checking and verifying the extent to which the Information contained in this publication is applicable to an order at the time the order is placed. All Information given herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied. Statements of suitability for certain applications are based on KEMET Electronics Corporation’s (“KEMET”) knowledge of typical operating conditions for such applications, but are not intended to constitute – and KEMET specifi cally disclaims – any warranty concerning suitability for a specifi c customer application or use. The Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by KEMET with reference to the use of KEMET’s products is given gratis, and KEMET assumes no obligation or liability for the advice given or results obtained. Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. Although all product–related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicated or that other measures may not be required. Additional information about production site flexibility can be found KEMET is a registered trademark of KEMET Electronics Corporation. © KEMET Electronics Corporation • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com F3100_R41_Y2_300 • 8/15/2023 19