T340E686M025AT

Tantalum Through-Hole Capacitors – Molded Radial T340 Molded Radial Overview The compact, space-saving T340 is transfer molded in precision, with a high impact-resistant plastic that has excellent electrical, physical and moisture-resistant properties. The gold color plastic case permits laser marking with outstanding permanency and legibility. Marking is provided on the top of the case to allow visual inspection for proper polarity and placement after insertion. In addition, positive polarity identification is achieved by an easily recognized molded radius on the positive end of the case. Additionally, this physical polarity identification is readily observed after capacitor placement as a further aid in the prevention of possible reverse insertion. Standoffs, located in the base of all case sizes, provide vents for air circulation and also to allow easy removal of flux residues from leadwire and circuit board solder joints. With very low impedance and ESR values, the T340 features exceptionally low DC leakage and DF characteristics. The T340 is available in standard ±20%, ±10%, and ±5% (special order) capacitance tolerance. T340 capacitors are highly reliable and exhibit performance characteristics typical of military test standards. Benefits Applications • Taped and reeled per EIA Specification RS-468 • Laser-marked case • Capacitance values of 0.1 μF – 330 μF • Tolerances of ±20% standard, ± 5% and ±10% special order • Voltage rating of 3 – 50 VDC • Case sizes: A, B, C, D, E, F Typical applications include bypassing, coupling, and timing applications in computers, military ordinance, industrial, entertainment, and consumer electronic equipment. Ordering Information T Capacitor Class T= Tantalum 340 A 105 M 035 Series Case Size Capacitance Code (pF) Capacitance Tolerance Rated Voltage (VDC) A, B, C, D, E, F First two digits represent significant figures. Third digit specifies number of zeros to follow. M = ±20% (standard K = ±10% J = ±5% (available on request) 003 = 3 006 = 6 010 = 10 015 = 15/16 020 = 20 025 = 25 035 = 35 040 = 40 050 = 50 Radial Lead Precision Molded Polar Solid Tantalum A S Failure Rate Termination Finish Not Applicable S = Standard (solder-coated copperweld) T = 100% tin (Sn)-plated Packaging Blank = Bulk 7301 = Tape & Reel 7305 = Ammo 7317 = Ammo Built Into Tomorrow © KEMET Electronics Corporation • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com T2041_T340 • 8/18/2023 1 Tantalum Through-Hole Capacitors – Molded Radial T340 Molded Radial Performance Characteristics Item Performance Characteristics Operating Temperature −55°C to 125°C Rated Capacitance Range 0.1 – 330 μF at 120 Hz/25°C Capacitance Tolerance M tolerance (20%) standard, J tolerance (5%), K tolerance (10%) special order Rated Voltage Range 3 –50 V DF (120 Hz at 25°C) Refer to Part Number Electrical Specification Table ESR and Impedance (100 kHz at 25°C) Refer to Part Number Electrical Specification Table (for reference only) Leakage Current Refer to Part Number Electrical Specification Table (at rated voltage up to +85°C and 2/3 of rated voltage applied at 125°C) Dimensions – Millimeters (Inches) Metric will govern T340 T T T T T SIDE W W H H L D A Case H L D S W W L D S B Case W H L D H L D S S S C Case D Case E Case F case size is the same as D, but with 0.200" (5.0 mm) lead spacing. Specify T340F when ordering this spacing. Case Size A B C D E F H** (MAXIMUM) W (MAXIMUM) 0.287 (7.3) 0.327 (8.3) 0.413 (10.5) 0.413 (10.5) 0.413 (10.5) 0.413 (10.5) 0.185 (4.7) 0.283 (7.2) 0.287 (7.3) 0.484 (12.3) 0.484 (12.3) 0.484 (12.3) T Lead Spacing (MAXIMUM) S 0.165 (4.2) 0.157 (4.0) 0.169 (4.3) 0.287 (7.3) 0.484 (12.3) 0.287 (7.3) 0.100 ±0.020 (2.5 ±0.5) 0.200±0.020 (5.0±0.5) 0.200±0.020 (5.0±0.5) 0.400±0.020 (10.0±0.5) 0.400±0.020 (10.0±0.5) 0.200±0.020 (5.0±0.5) Lead Length Lead Diameter L D 0.600±0.078 (15.0±2.0) 0.600±0.078 (15.0±2.0) 0.600±0.078 (15.0±2.0) 0.600±0.078 (15.0±2.0) 0.600±0.078 (15.0±2.0) 0.600±0.078 (15.0±2.0) 0.020±0.001 (0.50±0.03) 0.020±0.001 (0.50±0.03) 0.020±0.001 (0.50±0.03) 0.025±0.001 (0.64±0.03) 0.025±0.001 (0.64±0.03) 0.025±0.001 (0.64±0.03) **Includes Standoff Height of 0.015±0.005" (0.38±0.13 mm) for All Case Sizes. © KEMET Electronics Corporation • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com T2041_T340 • 8/18/20232 2 Tantalum Through-Hole Capacitors – Molded Radial T340 Molded Radial Table 1 – Ratings & Part Number Reference Rated Voltage Rated Capacitance (V) 85°C µF 3 3 3 3 3 3 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 15 15 15 15 15 15 15 15 10.0 15.0 33.0 47.0 68.0 100.0 6.8 10.0 12.0 15.0 18.0 22.0 27.0 33.0 39.0 47.0 56.0 68.0 82.0 100.0 120.0 150.0 180.0 220.0 330.0 4.7 5.6 6.8 8.2 10.0 12.0 15.0 18.0 22.0 27.0 33.0 39.0 47.0 56.0 68.0 82.0 100.0 120.0 150.0 220.0 3.3 3.9 4.7 5.6 6.8 8.2 10.0 12.0 (V) 85°C µF Rated Voltage Rated Capacitance Case Code A A B B C C A B B B B B C C C C C C D/F D/F D/F D/F D/F D/F E A B B B B B B C C C C C D/F D/F D/F D/F D/F D/F D/F E A B B B B B B C Case Code KEMET Part Number T340A106(1)003A(3) T340A156(1)003A(3) T340B336(1)003A(3) T340B476(1)003A(3) T340C686(1)003A(3) T340C107(1)003A(3) T340A685(1)006A(3) T340B106(1)006A(3) T340B126(1)006A(3) T340B156(1)006A(3) T340B186(1)006A(3) T340B226(1)006A(3) T340C276(1)006A(3) T340C336(1)006A(3) T340C396(1)006A(3) T340C476(1)006A(3) T340C566(1)006A(3) T340C686(1)006A(3) T340(2)826(1)006A(3) T340(2)107(1)006A(3) T340(2)127(1)006A(3) T340(2)157(1)006A(3) T340(2)187(1)006A(3) T340(2)227(1)006A(3) T340E337(1)006A(3) T340A475(1)010A(3) T340B565(1)010A(3) T340B685(1)010A(3) T340B825(1)010A(3) T340B106(1)010A(3) T340B126(1)010A(3) T340B156(1)010A(3) T340C186(1)010A(3) T340C226(1)010A(3) T340C276(1)010A(3) T340C336(1)010A(3) T340C396(1)010A(3) T340(2)476(1)010A(3) T340(2)566(1)010A(3) T340(2)686(1)010A(3) T340(2)826(1)010A(3) T340(2)107(1)010A(3) T340(2)127(1)010A(3) T340(2)157(1)010A(3) T340E227(1)010A(3) T340A335(1)015A(3) T340B395(1)015A(3) T340B475(1)015A(3) T340B565(1)015A(3) T340B685(1)015A(3) T340B825(1)015A(3) T340B106(1)015A(3) T340C126(1)015A(3) (see below for part options) KEMET Part Number DC Leakage DF IMP Ω µA at 25°C Maximum/5 Minutes 1.0 1.0 1.5 3.0 4.0 5.0 1.0 1.0 1.0 1.0 1.0 2.5 2.5 2.5 2.5 3.0 5.0 5.0 5.0 5.0 5.0 8.0 10.0 10.0 10.0 1.0 1.0 1.0 1.0 1.0 1.0 3.0 3.0 3.0 3.0 5.0 5.0 5.0 5.0 5.0 8.0 10.0 10.0 10.0 10.0 1.0 1.0 1.0 1.0 1.0 1.0 3.0 3.0 µA at 25°C Maximum/5 Minutes % at 25°C 120 Hz Maximum 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 8 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 % at 25°C 120 Hz Maximum at 10 kHz Maximum at 10 kHz Maximum DC Leakage DF IMP Ω 6.0 3.2 2.1 1.8 1.5 1.2 6.0 2.1 1.5 0.8 0.5 7.5 2.5 1.7 1.0 0.5 9.0 3.2 (1) To complete KEMET part number, insert M for ±20%, K for ±10% or J for 5%. Designates Capacitance tolerance. (2) To complete KEMET part number, insert letter "D" for 10.0 mm (0.394) lead spacing or letter "F" for 5.0 mm (0.197) lead spacing. Designates Lead spacing. (3) To complete KEMET part number, insert T = 100% Matte Tin (Sn) Plated,  S = Standard Solder coated (SnPb 5% Pb minimum). Designates termination finish. Higher voltage and better capacitance tolerance products may be substitued for an order within the same case size at KEMET's option. © KEMET Electronics Corporation • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com T2041_T340 • 8/18/20233 3 Tantalum Through-Hole Capacitors – Molded Radial T340 Molded Radial Table 1 – Ratings & Part Number Reference cont. Rated Voltage Rated Capacitance (V) 85°C µF 15 15 15 15 15 15 15 15 15 15 15 15 20 20 20 20 20 20 20 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 35 15.0 18.0 22.0 27.0 33.0 39.0 47.0 56.0 68.0 82.0 100.0 150.0 2.2 3.3 4.7 6.8 15.0 47.0 100.0 1.5 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10.0 12.0 15.0 18.0 22.0 27.0 33.0 39.0 47.0 68.0 0.10 0.15 0.22 0.33 0.47 0.68 1.0 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 (V) 85°C µF Rated Voltage Rated Capacitance Case Code C C C C C D/F D/F D/F D/F D/F E E A B B B C D E A B B B B C C C C C C D/F D/F D/F D/F D/F D/E/F E A A A A A A A B B B B B B/C C C C Case Code KEMET Part Number T340C156(1)015A(3) T340C186(1)015A(3) T340C226(1)015A(3) T340C276(1)015A(3) T340C336(1)015A(3) T340(2)396(1)015A(3) T340(2)476(1)015A(3) T340(2)566(1)015A(3) T340(2)686(1)015A(3) T340(2)826(1)015A(3) T340E107(1)015A(3) T340E157(1)015A(3) T340A225(1)020A(3) T340B335(1)020A(3) T340B475(1)020A(3) T340B685(1)020A(3) T340C156(1)020A(3) T340D476(1)020A(3) T340E107(1)020A(3) T340A155(1)025A(3) T340B275(1)025A(3) T340B335(1)025A(3) T340B395(1)025A(3) T340B475(1)025A(3) T340C565(1)025A(3) T340C685(1)025A(3) T340C825(1)025A(3) T340C106(1)025A(3) T340C126(1)025A(3) T340C156(1)025A(3) T340(2)186(1)025A(3) T340(2)226(1)025A(3) T340(2)276(1)025A(3) T340(2)336(1)025A(3) T340(2)396(1)025A(3) T340(2)476(1)025A(3) T340E686(1)025A(3) T340A104(1)035A(3) T340A154(1)035A(3) T340A224(1)035A(3) T340A334(1)035A(3) T340A474(1)035A(3) T340A684(1)035A(3) T340A105(1)035A(3) T340B125(1)035A(3) T340B155(1)035A(3) T340B185(1)035A(3) T340B225(1)035A(3) T340B275(1)035A(3) T340(2)335(1)035A(3) T340C395(1)035A(3) T340C475(1)035A(3) T340C565(1)035A(3) (see below for part options) KEMET Part Number DC Leakage DF IMP Ω µA at 25°C Maximum/5 Minutes 3.5 4.0 4.0 5.0 5.0 7.0 7.0 8.0 9.0 10.0 10.0 10.0 1.0 1.0 1.5 2.5 5.0 9.0 10.0 1.0 1.0 1.0 1.0 2.0 2.0 3.0 3.0 3.5 3.5 4.0 5.0 5.5 7.0 8.0 10.0 10.0 10.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 2.5 2.5 µA at 25°C Maximum/5 Minutes % at 25°C 120 Hz Maximum 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 % at 25°C 120 Hz Maximum at 10 kHz Maximum at 10 kHz Maximum DC Leakage DF IMP Ω 2.5 2.1 1.3 1.1 0.8 0.6 12.0 8.0 5.5 4.2 2.5 1.3 0.8 17.0 5.5 4.2 3.0 2.0 1.5 1.3 0.9 220.0 150.0 100.0 75.0 50.0 36.0 25.0 15.0 11.0 7.5 5.5 (1) To complete KEMET part number, insert M for ±20%, K for ±10% or J for 5%. Designates Capacitance tolerance. (2) To complete KEMET part number, insert letter "D" for 10.0 mm (0.394) lead spacing or letter "F" for 5.0 mm (0.197) lead spacing. Designates Lead spacing. (3) To complete KEMET part number, insert T = 100% Matte Tin (Sn) Plated,  S = Standard Solder coated (SnPb 5% Pb minimum). Designates termination finish. Higher voltage and better capacitance tolerance products may be substitued for an order within the same case size at KEMET's option. © KEMET Electronics Corporation • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com T2041_T340 • 8/18/20234 4 Tantalum Through-Hole Capacitors – Molded Radial T340 Molded Radial Table 1 – Ratings & Part Number Reference cont. Rated Voltage Rated Capacitance (V) 85°C µF 35 35 35 35 35 35 35 35 35 35 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 6.8 8.2 10.0 12.0 15.0 18.0 22.0 27.0 33.0 47.0 0.10 0.15 0.22 0.33 0.47 0.68 1.0 1.5 2.2 3.3 4.7 6.8 10.0 15.0 22.0 33.0 47.0 0.10 0.15 0.22 0.33 0.39 0.47 0.56 0.68 0.82 1.0 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10.0 12.0 15.0 18.0 22.0 (V) 85°C µF Rated Voltage Rated Capacitance Case Code C C C/D D/F D/F D/F D/F D/F D/E/F E A A A A A A A B B C C C D D D E E A A A A B B B B B B B B/C B B/C C C/D C C/D C D/F D/F D/F D/F D/F D/F E Case Code KEMET Part Number T340C685(1)035A(3) T340C825(1)035A(3) T340(2)106(1)035A(3) T340(2)126(1)035A(3) T340(2)156(1)035A(3) T340(2)186(1)035A(3) T340(2)226(1)035A(3) T340(2)276(1)035A(3) T340(2)336(1)035A(3) T340E476(1)035A(3) T340A104(1)040A(3) T340A154(1)040A(3) T340A224(1)040A(3) T340A334(1)040A(3) T340A474(1)040A(3) T340A684(1)040A(3) T340A105(1)040A(3) T340B155(1)040A(3) T340B225(1)040A(3) T340C335(1)040A(3) T340C475(1)040A(3) T340C685(1)040A(3) T340D106(1)040A(3) T340D156(1)040A(3) T340D226(1)040A(3) T340E336(1)040A(3) T340E476(1)040A(3) T340A104(1)050A(3) T340A154(1)050A(3) T340A224(1)050A(3) T340A334(1)050A(3) T340B394(1)050A(3) T340B474(1)050A(3) T340B564(1)050A(3) T340B684(1)050A(3) T340B824(1)050A(3) T340B105(1)050A(3) T340B125(1)050A(3) T340(2)155(1)050A(3) T340B185(1)050A(3) T340(2)225(1)050A(3) T340C275(1)050A(3) T340(2)335(1)050A(3) T340C395(1)050A(3) T340(2)475(1)050A(3) T340C565(1)050A(3) T340(2)685(1)050A(3) T340(2)825(1)050A(3) T340(2)106(1)050A(3) T340(2)126(1)050A(3) T340(2)156(1)050A(3) T340(2)186(1)050A(3) T340E226(1)050A(3) (see below for part options) KEMET Part Number DC Leakage DF IMP Ω µA at 25°C Maximum/5 Minutes 3.0 4.0 4.0 5.0 5.0 8.0 8.0 10.0 10.0 10.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.7 2.3 3.0 3.5 4.5 6.0 9.0 10.0 10.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.1 1.1 1.5 1.5 2.5 3.0 3.5 4.0 5.0 6.0 7.0 8.0 9.0 10.0 10.0 µA at 25°C Maximum/5 Minutes % at 25°C 120 Hz Maximum 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 % at 25°C 120 Hz Maximum at 10 kHz Maximum DC Leakage DF IMP Ω 4.2 2.8 2.2 1.9 1.4 1.1 200.0 140.0 95.0 70.0 46.0 34.0 23.0 14.0 10.0 7.0 5.0 3.9 2.6 2.0 1.7 1.3 1.0 220.0 150.0 100.0 75.0 50.0 36.0 25.0 15.0 11.0 7.5 5.5 4.0 2.8 2.2 1.7 at 10 kHz Maximum (1) To complete KEMET part number, insert M for ±20%, K for ±10% or J for 5%. Designates Capacitance tolerance. (2) To complete KEMET part number, insert letter "D" for 10.0 mm (0.394) lead spacing or letter "F" for 5.0 mm (0.197) lead spacing. Designates Lead spacing. (3) To complete KEMET part number, insert T = 100% Matte Tin (Sn) Plated,  S = Standard Solder coated (SnPb 5% Pb minimum). Designates termination finish. Higher voltage and better capacitance tolerance products may be substitued for an order within the same case size at KEMET's option. © KEMET Electronics Corporation • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com T2041_T340 • 8/18/20235 5 Tantalum Through-Hole Capacitors – Molded Radial T340 Molded Radial Recommended Voltage Derating Guidelines 85°C to 125°C VR 66% of VR 120% 100% % Working Voltage % Change in working DC voltage with temperature −55°C to 85°C 80% % Change in working DC voltage with temperature 60% 67% 40% 20% 0% -55 25 45 85 Temperature (°C) 105 125 Ripple Current/Ripple Voltage Permissible AC ripple voltage and current are related to equivalent series resistance (ESR) and the power dissipation capabilities of the device. Permissible AC ripple voltage that may be applied is limited by following criteria: 1. Dissipated power must not exceed the limits specified for the Series. 2. The positive peak AC voltage plus the DC bias voltage, if any, must not exceed the DC voltage rating of the capacitor. 3. The negative peak AC voltage in combination with bias voltage, if any, must not exceed the allowable limits specified for reverse voltage. Thermal capacities for the various case sizes have been determined empirically and are listed below. The “ripple voltage” permissible may be calculated from the impedance and ESR data shown in the respective product section. © KEMET Electronics Corporation • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com Temperature Compensation Multipliers for Maximum Power Dissipation T ≤ 25°C 1.00 T ≤ 85°C 0.90 T ≤ 125°C 0.40 T= Environmental Temperature Maximum allowable rms ripple voltage or current may be determined as follows: I(max) = √P max/R E(max) = √P max/R I = rms ripple current (amperes) E = rms ripple voltage (volts) P max = Maximum power dissipation (watts) R = ESR at specified frequency (ohms) Case Size Maximum Power Dissipation (Pmax) Watts at 25°C A B C D/F 0.09 0.09 0.100 0.125 T2041_T340 • 8/18/20236 6 Tantalum Through-Hole Capacitors – Molded Radial T340 Molded Radial Optimum Solder Wave Profile Solder Wave Peak Temperature 260ºC Entrance to Solder Wave Degrees – Cº Flux Zone 250 225 200 175 150 125 100 75 50 25 Exit from Solder Wave (Time in Wave – 2 to 4 Seconds) Preheat Zone Hot Air Debridging Exit from Solder Machine 80ºC to 120ºC Entrance to Solder Machine Free Air Cool Bottom Side Temperature Range Entrance to In-Line Cleaner Exit from In-Line Cleaner (time in cleaner may be less) Immersion in Cleaning Vapor 150ºC Maximum Top Side Nominal 0 1 2 3 Time (Minutes) 4 5 6 Reverse Voltage Although these are polar capacitors, some degree of transient voltage reversal is permissible, as seen below. The capacitors should not be operated continuously in reverse mode, even within these limits. Temperature Pecentage of Rated Voltage +25°C +85°C +125°C 15 5 1 © KEMET Electronics Corporation • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com T2041_T340 • 8/18/20237 7 Tantalum Through-Hole Capacitors – Molded Radial T340 Molded Radial Mounting All encased capacitors will pass the Resistance to Soldering Heat Test of MIL–STD–202, Method 210, Condition C. This test simulates wave solder of topside board mount product. This demonstration of resistance to solder heat is in accordance with what is believed to be the industry standard. More severe treatment must be considered reflective of an improper soldering process. The above figure is a recommended solder wave profile for both axial and radial leaded solid tantalum capacitors. Capacitor Marking American Capacitance (in Microfarads) Polarity Voltage 4.7J + 10 K KEMET Trademark 10K + 16 K A Case B Case 33K + 10 K C Case 47J + 16 K D & F Case 220J + 10 K Capacitance Tolerance ±5% - J ±10% - K ±20% - Standard, (no marking) E Case European Capacitance (in Microfarads) Polarity Voltage 4.7J + 10 K A Case Capacitance (in Microfarads) Voltage Polarity KEMET Trademark 10K + 16 K B Case 33K + 10 K C Case 47J + 16 K D & F Case 220J + 10 K Capacitance Tolerance ±5% - J ±10% - K ±20% - Standard, (no marking) E Case Capacitance Tolerance: 5% - J 10% - K 20% - Standard, (no marking) KEMET Trademark © KEMET Electronics Corporation • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com T2041_T340 • 8/18/20238 8 Tantalum Through-Hole Capacitors – Molded Radial T340 Molded Radial Storage Tantalum molded radial capacitors should be stored in normal working environments. KEMET recommends that maximum storage temperature not exceed 40°C and maximum storage humidity not exceed 60°C RH. Storage at high temperature may cause a small, temporary increase in leakage current (measured under standard conditions), but the original value is usually restored within a few minutes after application of rated voltage. Storage at high humidity may increase capacitance and dissipation factor. Solderability will be degraded by exposure to high temperatures, high humidity, corrosive atmospheres, and long term storage. For optimized solderability capacitors stock should be used promptly, preferably within three years of receipt. Tape & Reel Packaging Information KEMET offers Solid Tantalum Capacitors fully compatible for use with automatic insertion machines for radial-lead components. Aris Reeling meets all requirements of EIA Standard RS-468. KEMET capacitors are wound on a precision made ARIS Reel Package. ARIS Ammo Package is also available. Table 2 – Packaging Quantity Case Size Standard Bulk Quantity Standard Reel Quantity Reel C-Spec Ammo Pack Quantity A 300 1,000 C-7301 1,600 B 300 1,000 C-7301 1,500 C 200 1,000 C-7301 1,500 D 100 250 C-7301 450 E 50 150 C-7301 N/A F 100 N/A N/A N/A © KEMET Electronics Corporation • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com T2041_T340 • 8/18/20239 9 Tantalum Through-Hole Capacitors – Molded Radial T340 Molded Radial Figure 1 A1 P2 1 2 3 A P W2 F W0 W 1 T370 2 T340** 3 T330** D0 d L1 T P1 W1 H1 H W2 P0 Dimension Symbol Nominal mm (inch) Tolerance mm (inch) Body Height (1) A 10.50 (0.413) ±0.38 (±0.015) Maximum Body Width (1) A1 15.24 (0.600) ±0.38 (±0.015) Maximum Sprocket Hole Diameter D0 4.0 (0.157) ±0.3 (±0.012) Lead Diameter d 0.51 (0.020) or 0.64 (0.025) Lead Center (5) F Component Base to Tape Center (2) (4) (6) H Lead Standoff Height H0 Component Height Above Tape Center H1 32.25 (1.270) Maximum Component Alignment Front to Rear ΔH 0 ±2.0 (±0.079) 5.0 (0.197) 2.5 (0.098) 16.0 – 21.0 (0.630 – 0.827) ±0.05 ±0.03 (±0.001) +0.8 (+0.032) −0.2 (−0.008) Reference Only N/A Cut Out Length L 11.0 (0.433) Maximum Lead Protrusion L1 2.0 (0.079) Maximum Component Pitch (5) P 12.7 (0.500) ±1.0 (±0.039) Sprocket Hole Pitch (3) P0 12.7 (0.500) ±0.03 (±0.012) Sprocket Hole Center to Lead Center (4) (5) P1 Sprocket Hole Center to Component Center P2 6.35 (0.250) ±1.31 (±0.051) Body Thickness T0 6.35 (0.250) ±1.3 Maximum 3.85 (0.152) 4.76 (0.188) 5.1 (0.201) ±0.7 (±0.028) Total Tape Thickness T 0.7 (0.28) ±0.02 (±0.008) Carrier Tape Width W 18.0 (0.709) +1.0/−0.5 (+0.039/−0.020) Hold-Down Tape Width W0 15 (0.561) or 6 (0.236) +1.0/−0.8 (+0.039/−0.031 Sprocket Hole Location W1 9.0 (0.354) +0.075/−0.5 (+0.030/−0.020) Hold-Down Tape Location W2 3.0 (0.118) or 12.0 (0.472) Maximum Notes: (1) See Dimensions table for specific values per case size (2) Reference only (3) Cumulative pitch error ±1.0 mm (0.039") maximum in 20 consecutive sprocket hole locations. (4) Measured at bottom of standoff. (5) P, P1 and F measured at egress from carrier tape. (6) H dimensions for T370 D and E 16.5 mm ±0.5 mm (0.650"±0.020") On polar devices, the positive (+) lead exits from container first. * Lead spacings are 2.5 mm (0.098") center to center ** Lead spacings are 5.0 mm (0.197") center to center. © KEMET Electronics Corporation • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com T2041_T340 • 8/18/2023 10 10 Tantalum Through-Hole Capacitors – Molded Radial T340 Molded Radial KEMET Electronics Corporation Sales Offices For a complete list of our global sales offi ces, please visit www.kemet.com/sales. Disclaimer YAGEO Corporation and its affi liates do not recommend the use of commercial or automotive grade products for high reliability applications or manned space fl ight. All product specifi cations, statements, information and data (collectively, the “Information”) in this datasheet are subject to change. The customer is responsible for checking and verifying the extent to which the Information contained in this publication is applicable to an order at the time the order is placed. All Information given herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied. Statements of suitability for certain applications are based on KEMET Electronics Corporation’s (“KEMET”) knowledge of typical operating conditions for such applications, but are not intended to constitute – and KEMET specifi cally disclaims – any warranty concerning suitability for a specifi c customer application or use. The Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by KEMET with reference to the use of KEMET’s products is given gratis, and KEMET assumes no obligation or liability for the advice given or results obtained. Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. Although all product–related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicated or that other measures may not be required. KEMET is a registered trademark of KEMET Electronics Corporation. © KEMET Electronics Corporation • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com T2041_T340 • 8/18/2023 1 11