T523H107M035APE070

Preliminary Specification KO-CAP (KEMET Organic Capacitor) T523H107M035APE070: 7360-20, 100 uF, 35 V, 70 mΩ Environmental Compliance RoHS Compliant (6/6) per EU Directive 2002/95/EC Halogen Free Part Number Information Capacitor Class Series T 523 Facedown Polymer Tantalum Case Size Capacitance Code Capacitance Tolerance Voltage Failure Rate/ Lead Material Design P Ni-Pd-Au Plated ESR Code H 107 M 035 A 7360-20 100 uF ± 20% 35 V N/A E070 DF % @ 25°C, 120 Hz Maximum ESR mΩ @ 25°C 100kHz Maximum Maximum Allowable Ripple Current mArms @ 45° C 100kHz MSL Reflow Temp ≤260ºC Maximum Operating Temperature °C 10 70 2500 3 85 70 mΩ Performance Characteristics KEMET Part Number Rated Voltage (V) T523H107M035APE070 35 DC Leakage Rated µA @ Vr, 25°C Capacitance Maximum/ (uF) 5 Minutes 100 350 Qualification Test Condition Endurance 85° C @ Rated Voltage, 2000 hours Storage 85°C @ 0 Volts, 2000 hours Humidity 60° C, 90% RH, 500 hours, No Load Temperature Stability Extreme temperature exposure at a succession of continuous steps at +25°C, -55°C, +25°C, +85°C, +25°C Surge Voltage 85° C, 1.32 x Rated Voltage, 33 W Resistance, 1000 cycles Mechanical Shock/ Vibration MIL-STD-202, Method 213, Condition I, 100G Peak MIL-STD-202, Method 204, Condition D, 10 Hz to 2000 Hz, 20G Peak KO-CAP Polymer Capacitors ΔC/C DF DCL ESR ΔC/C DF DCL ESR ΔC/C DF DCL ESR Characteristics Within -20/+10% of initial value Within initial limit Within 1.25 x initial limit Within 2.0 x initial limit Within -20/+10% of initial value Within initial limit Within 1.25 x initial limit Within 2.0 x initial limit Within -5/+35% of initial value Within initial limit Wihtin 5.0 x initial limit Within 2.0 x initial limit ΔC/C DF DCL ΔC/C DF DCL ESR ΔC/C DF DCL +25°C -55°C +85°C Initial Limit +-20% +-20% Initial Limit Initial Limit 1.2 x Initial Limit Initial Limit N/A 10 x Initial Limit Within -20/+10% of initial value Within initial limit Within initial limit Within initial limit Within ±10% of initial value Within initial limit Within initial limit KEMET Electronics Corporation KLM2015 Preliminary Specification KO-CAP (KEMET Organic Capacitor) T523H107M035APE070: 7360-20, 100 uF, 35 V, 70 mΩ Dimensions (units: mm) Case Size Component Dimensions KEMET EIA L W H F S H 7360-20 7.3 ± 0.3 6.0 ± 0.3 1.9±0.10 4.45±0.10 1.60±0.30 Tantalum Polymer Rated Voltage KO 107 35 K 748 Polarity Indicator (+) Picofarad Code KEMET ID PWC* * 748 = 48th week of 2017 Manufacturing Location(s) Fabrication Site Assembly/Packaging Site Continent North America North America Country US US Region South Carolina South Carolina Test Site North America US Mexico South Carolina Tamaulipas Reflow Profile Profile Feature Pb-Free Assembly Preheat/Soak Temperature Minimum (TSmin) Temperature Maximum (TSmax) Temperature Time (ts) from Tsmin to Tsmax) Ramp-up Rate (TL to TP) Liquidous Temperature (T L) Time Above Liquidous (tL) Peak Temperature (TP) 150° C 200° C 60-120 seconds 3° C/sec maximum 217° C 60-150 seconds 250° C* 260° C** Time within 5° C of Maximum Peak Temperature (tP) 30 seconds maximum Ramp-down Rate (TP to TL) 6° C/second maximum Time 25° C to Peak Temperature 8 minutes maximum Note: All temperatures refer to the center of the package, measured on the package body surface that is facing up during assembly reflow. * PackageThickness ≥ 2.5 mm ** PackageThickness < 2.5 mm The Customer acknowledges the following limitations of the prototype samples: (1) prototype samples are manufactured from preliminary designs and manufacturing processes, may not represent final designs, have not been released for commercial use and are not subject to the same quality control procedures applicable to released products; (2) prototype samples are not qualified parts and are provided as-is by KEMET Electronics Corporation, which specifically disclaims any and all warranties and guarantees, explicit or implied, including without limitation the warranties of merchantability and fitness for a particular purpose or use; (3) prototype samples are not intended for commercial use, are provided for engineering evaluation only and are not recommended for use in the Customer’s production line; and (4) the Customer assumes the risk of any and all uses that the Customer makes of the prototype samples. COPYRIGHT KEMET ELECTRONICS CORPORATION 2015. All rights reserved KO-CAP Polymer Capacitors KEMET Electronics Corporation KLM2015