USEQMSM1220900

Motion Sensors QMS Pyroelectric Infrared Motion Sensors, I2C-SMD Overview Applications KEMET’s QMS thin film digital pyroelectric IR sensors combine high sensitivity with fast response times to ensure rapid and accurate motion detection, and high dynamic range to allow motion detection nearby or over larger distances. The 2x2 pixel version of this device allows users to determine direction of motion. • Contactless switching • Office automation equipment • Home applicances • Lighting • Display products • Air-conditioners • TV • PC monitors • Rice cookers • Smart toilets These high quality sensors, in their small SMD package, integrate a digital, current mode read-out. Industry standard I2C communication enables plug-and-play connectivity to microcontrollers and allows easy tuning. Programmable gain and filtering offer maximum flexibility in system design, and various low power modes, including a wake-up by motion feature, are also available. These sensors can be connected toegther in linear series to allow synchronized sampling across devices. Benefits • High sensitivity with fast response time • High dynamic range • Small SMD package • I2C communication • Digital output • Programmable gain and filltering • Various pixel and aperture configurations • Ultra-low power comsumption and standby modes, motion triggered wake-up One world. One KEMET © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com SE0212_QMS • 2/6/2020 1 Motion Sensors – QMS Pyroelectric Infrared Motion Sensors, I2C-SMD Ordering Information USE QMS E A 0116 8 0 Product Family Series Sensor Type Mounting Type Specification Packaging Version 0 = Bulk 8 = 7" Tape & Reel 0 Sensors QMS = SMD IR Motion Sensors E = Serial output M = Serial module K = Evaluation kit A = Sensor only 1 = Module type 1 or kit type 1 L = Lens S = Small lens 0116 = 1x1 pixel, 1.65 aperture, 5.0 µm Long Pass 2216 = 2x2 pixel, 1.65 aperture, 5.0 µm Long Pass 2209 = 2x2 pixel, 0.9 aperture, 5.0 µm Long Pass Environmental Compliance All KEMET Motion Sensors are RoHS and REACH Compliant. Article 33(1) of the REACH Regulation states that manufacturers and importers of articles (products) are required to notify their customers of the presence of any Substances of Very High Concern (SVHC) in their products exceeding 0.1% by weight and provide instructions on safe use of the product. KEMET Corporation reports regarding the Article 33(1) of REACH Regulation as follows: 1. Applicable Product: Motion Sensors (QMS series) 2. Report for the content of REACH SVHC list: The product(s) above contains a substance by more than 0.1wt% per product weight that was published in the 8th update of the REACH SVHC substances (December 19, 2012). 3. Regarding the safety of the motion sensors (Piezoceramic products): The Piezoceramic that is used in this product becomes ceramic by sintering powder containing PZT as the main ingredient. It is chemically stable, with minimum risks toward the human body or environment within the intended use of the product. Please note that risks could occur in the case of inhalation or accidental oral uptake of powder ceramics. 4. Technical product information on the motion sensors (Piezoceramic products): The manufacturing technique of the “piezoceramic products” whose main ingredient is Lead Titanium Zirconium Oxide (PZT) has been established, and there is no alternative material that can exhibit superior performance than PZT at this moment. Please note that the piezoceramic is listed as an exempt on RoHS (2011/65/EU) AnnexIII (7c.1). 5. The responsibility of piezoceramic manufacturers: Piezoceramic manufacturers report information regarding PZT containment in their products to the customers to obey the article 33 of the REACH regulation © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com SE0212_QMS • 2/6/2020 2 Motion Sensors – QMS Pyroelectric Infrared Motion Sensors, I2C-SMD Dimensions – Millimeters Sensor 1.700 0.725 3.700 28 1 15 9 Ø1.650 or Ø0.90 0.325 0.400 1.200 4.600 0.975 5.650 2.050 23 0.226 0.250 24 14 10 0.500 3.050 0.550 1.370 1.55 Maximum 24 - SYNC 25 - INT 26 - SDA 27 - SCL Pin 1 Indication 28 - GND Pin Configuration of Sensor VSupply - 1 CAP - 3 23 - CS 29 - GND GND - 5 GND - 7 21 - CLK 19 - GND 30 - GND 17 - GND TRANSPARENT TOP VIEW © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com SE0212_QMS • 2/6/2020 3 Motion Sensors – QMS Pyroelectric Infrared Motion Sensors, I2C-SMD Dimensions – Millimeters cont. Module 10.000 16.000 8.5 3.6 16 13.800 Field of View Single Element 2x2 Array Sensor Element Pixel Mapping Field of View Large Aperture © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com Small Aperture SE0212_QMS • 2/6/2020 4 Motion Sensors – QMS Pyroelectric Infrared Motion Sensors, I2C-SMD Performance Characteristics Signal Filtering & Power Modes Power Mode (base sample rate) High Pass Filter – Analog (Hz) Fixed Analog Low Pass Filter (Hz) Fixed Digital Low Pass Filter (Hz) Digital Low Pass Filter (Hz) Maximum ADC Sampling Rate (sps) Normal Power Mode Off 1.0 2.0 4.0 8.0 600 250 180.0 90.0 45.0 22.5 1,000 Low Power Mode Off 0.17 0.33 0.66 1.30 100 42 30.00 15.00 7.50 3.75 166 Item Power consumption Operational state Mode Description Typical Current Consumption (1.8 V, room temperature) Normal Power Mode Normal power consumption, 1 kHz maximum sample rate 22 µA Low Power Mode Low power consumption, 166 Hz maximum sample rate 3.5 µA Normal Operation Mode Sensor signal readout over I2C 22 µA Sleep Mode Hardware interrupt on infrared trigger 21 µA (Normal Power Mode) 3.5 µA (Low Power Mode) Power Down Mode Sensor is disabled 1.1 µA Infrared Frequency Characteristics Typical Frequency Response in Normal Power Mode Typical Frequency Response in Low Power Mode © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com Typical Frequency Response at Different Gain Settings SE0212_QMS • 2/6/2020 5 Motion Sensors – QMS Pyroelectric Infrared Motion Sensors, I2C-SMD Part Number Specifications Electrical Characteristics Supply Supply Voltage Current (V) (μA) Typical 1.75 to 3.60 1 to 23 Digital I/O ΔΣ ADC at 1 ksp I2C (FM+ compatible) 15 bit Operating Storage Temperature Temperature Range (°C) Range (°C) −40 to +85 −40 to +110 Sensor Read-out Configurable Current mode Gain Digital filtering Sampling rate Power modes Part Number (Sensor) Part Number Filter Aperture (mm) USEQMSEA011680 φ 1.65 USEQMSEA221680 φ 1.65 USEQMSEA220980 1 φ 0.90 Element Size (mm2) 0.410 (1 pixel) 4 x 0.057 (4 pixel) 4 x 0.057 (4 pixel) SMD Package (mm) 5.65 x 3.70 x 1.55 D* (cm√Hz/W) Typical NEP (W/√Hz) Typical 2.5 x 108 2.7 x 10–10 5.5 x 10 0.4 x 10 1 8 1 Time Constant (ms) at 10–20 Hz peak Filter Weight (gr) 0.07 5.0 μm Long Pass ~10 –10 0.07 0.07 10 Hz, 500 K, room temperature, without window and optics. Part Number (Module) Part Number Comment Weight (gr) USEQMSM1011600 Includes sensor: USEQMSEA011680 5.40 USEQMSM1221600 Includes sensor: USEQMSEA221680 5.40 USEQMSM1220900 Includes sensor: USEQMSEA220980 5.40 Part Number (Evaluation Kit) Part Number Comment Weight (gr) USEQMSKL011600 Includes sensor: USEQMSEA011680, motion sensing, with Fresnel lens 300 USEQMSKL221600 Includes sensor: USEQMSEA221680, motion and motion direction sensing, with Fresnel lens 300 USEQMSKS221600 Includes sensor: USEQMSEA221680, long range, with Fresnel lens 300 USEQMSK1220900 Includes sensor: USEQMSEA220980, medium range, no optics 300 USEQCSK0000000 Control board for modules, maximum 4 modules can be connected on one control board 250 © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com SE0212_QMS • 2/6/2020 6 Motion Sensors – QMS Pyroelectric Infrared Motion Sensors, I2C-SMD Landing Pattern Recommended PCB Landing Pattern Part Schematic Analog Front-End Reference/Regulator VDD VCC (1.8 - 3.6 V) 15b ∆Σ ADC Digital Filter FIFO Timing Ctrl Interrupt Ctrl Wake-up CS INT SDA SCL I2C Sensor Block Diagram - Single Element M C U CLK SYNC Clock Generator GND >100nF © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com SE0212_QMS • 2/6/2020 7 Motion Sensors – QMS Pyroelectric Infrared Motion Sensors, I2C-SMD Part Schematic cont. S1 S2 Analog Front-End S3 CS INT SDA SCL Digital Filter FIFO Timing Ctrl Interrupt Ctrl Wake-up 15b ∆Σ ADC VDD M C U CLK SYNC S4 Reference/Regulator I2C Block Diagram - 2 x 2 Pixel Clock Generator GND VCC (1.8 - 3.6 V) >100nF Soldering Process Recommended Reflow Soldering Profile Preheat/Soak Temperature Minimum (TSmin) Temperature Maximum (TSmax) Time (ts) from Tsmin to Tsmax 150°C 200°C 60 – 120 seconds Ramp-Up Rate (TL to TP) 3°C/second maximum Time Above Liquidous (tL) 60 – 150 seconds Liquidous Temperature (TL) Peak Temperature (TP) Time within 5°C of Maximum Peak Temperature (tP)1 Ramp-Down Rate (TP to TL) Time 25°C to Peak Temperature 1 Pb-Free Assembly 217°C 260°C TP TL Temperature Profile Feature tP Maximum Ramp-up Rate = 3°C/second Maximum Ramp-down Rate = 6°C/second TC −5°C tL Tsmax Tsmin ts 25 25°C to Peak Time 30 seconds maximum 6°C/second maximum 8 minutes maximum Tolerance for peak profile temperature (TP) is defined as a supplier minimum and as a user maximum. Packaging Series Packaging Type Pieces per Reel QMS 7" Tape & Reel 800 © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com SE0212_QMS • 2/6/2020 8 Motion Sensors – QMS Pyroelectric Infrared Motion Sensors, I2C-SMD Taping Specification Dimensions (mm) Minimum Typical Maximum P0 P T P2 W A0 B0 K0 E F D0 3.90 4.00 4.10 7.90 8.00 8.10 0.25 0.30 0.35 1.90 2.00 2.10 11.70 12.00 12.30 3.90 4.00 4.10 5.85 5.95 6.05 1.65 1.75 1.85 1.65 1.75 1.85 5.40 5.50 5.60 1.50 1.50 1.60 Reel Specification Dimensions (mm) Tolerance Nominal C1 C2 A B H T D ±1.0 Ø178 ±0.2 13.5 ±0.2 2.3 ±0.2 10.4 ±0.5 12.5 ±0.2 1.6 ±0.5 Ø54 © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com SE0212_QMS • 2/6/2020 9 Motion Sensors – QMS Pyroelectric Infrared Motion Sensors, I2C-SMD Handling Precautions Pyroelectric Infrared Sensors should be kept away from indirect and direct sunlight, the headlights of cars, wind, and exposure to strong vibration and strong shock. Do not use in water, alcohol ETA, corrosive gas or under sea breeze. Do not expose to corrosive substances. Do not drop or apply any mechanical stress. The performance of this device can be affected by ESD. Precautions should be used when handling and installing the sensor. Precision devices such as this sensor can be damaged or caused not to meet published specification due to ESD. Please note that there is limited ESD protection built-in as the device is optimised for low power consumption and low noise operation. Human Body Model (HBM), per JS-001: 2,000 V. The sensor is classed as Moisture Sensitivity Level 3 (MSL-3). The package should be handled according to IPC/JEDEC J-STD-20. Pyroelectric Infrared Sensors should be stored in normal working environments. Solderability will be degraded by exposure to high temperatures, high humidity, corrosive atmospheres, and long-term storage. KEMET recommends that ambient storage conditions are < 30°C and < 60% relative humidity and that maximum storage temperature does not exceed 110°C. Atmospheres should be free of chlorine and sulfur-bearing compounds. Temperature fluctuations should be minimized to avoid condensation on the parts. For optimized solderability sensors stock should be used promptly, preferably within 24 months of receipt. © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com SE0212_QMS • 2/6/2020 10 Motion Sensors – QMS Pyroelectric Infrared Motion Sensors, I2C-SMD KEMET Electronics Corporation Sales Offices For a complete list of our global sales offi ces, please visit www.kemet.com/sales. Disclaimer All product specifi cations, statements, information and data (collectively, the “Information”) in this datasheet are subject to change. The customer is responsible for checking and verifying the extent to which the Information contained in this publication is applicable to an order at the time the order is placed. All Information given herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied. Statements of suitability for certain applications are based on KEMET Electronics Corporation’s (“KEMET”) knowledge of typical operating conditions for such applications, but are not intended to constitute – and KEMET specifi cally disclaims – any warranty concerning suitability for a specifi c customer application or use. The Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by KEMET with reference to the use of KEMET’s products is given gratis, and KEMET assumes no obligation or liability for the advice given or results obtained. Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. Although all product–related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicted or that other measures may not be required. When providing KEMET products and technologies contained herein to other countries, the customer must abide by the procedures and provisions stipulated in all applicable export laws and regulations, including without limitation the International Traffi c in Arms Regulations (ITAR), the US Export Administration Regulations (EAR) and the Japan Foreign Exchange and Foreign Trade Act. KEMET is a registered trademark of KEMET Electronics Corporation. © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com SE0212_QMS • 2/6/2020 11