KUK114-50L

SMD S MD Type Logic level TOPFET KUK114-50L TO-263 Features + .1 1 .2 7 -00.1 Transistors IC Unit: mm +0.1 1.27-0.1 +0.2 4.57-0.2 Vertical power DMOS output stage Low on-state resistance Logic and protection supply from separate pin + .2 8 .7 -00.2 Low operating supply current Overload protection against over temperature Overload protection against short circuit load +0.1 1.27-0.1 0.1max +0.1 0.81-0.1 Protection circuit condition indicated by flag pin 5 V logic compatible input level Separate input pin for higher frequency drive ESD protection on input, flag and protection supply pins Over voltage clamping for turn off of inductive loads Both linear and switching operation are possible 2.54 +0.2 -0.2 +0.1 5.08-0.1 + .2 2 .5 4 -00.2 Latched overload protection reset by protection supply + .2 5 .2 8 -00.2 + .2 1 5 .2 5 -00.2 2.54 +0.2 0.4-0.2 Absolute Maximum Ratings Ta = 25 Parameter Continuous off-state drain source voltage Continuous input voltage Continuous flag voltage Continuous supply voltage VIS = Continuous drain current Continuous drain current Repetitive peak on-state drain current Total power dissipation Storage temperature Junction temperature Lead temperature VIS = Protection supply voltage Protected drain source supply voltage (VPS = VPSN) Protected drain source supply voltage (VPS = VPSN; L 10 ìH) VIS = 10 V; RI VIS = 5 V; RI VIS = 10 V; RI VIS = 5 V; RI 2 kÙ 1 kÙ 2 kÙ 1 kÙ PDSM C = 250 pF; R = 1.5 KÙ RIS 100 Ù VC IDRRM VDDP(P) VPSP VDDP(T) Tmb Tmb Tmb 25 100 25 ID ID IDRM Ptot Tstg Tj Tsold 7 4.4 50 50 25 45 0.8 2 15 VIS = 0 V Conditions Symbol VDSS VIS VFS VPS 7 15 9.5 60 40 -55 to +150 150 250 5 4 V V V V V V kW KV A Rating 50 11 11 11 5 13 8.5 54 Unit V V V V V A A A W Tmb = 25 Instantaneous overload dissipation Electrostatic discharge capacitor voltage Repetitive peak clamping drain current 5 .6 0 11 Input Gate 22 Drain Drain 33 Source Source www.kexin.com.cn 1 SMD Type KUK114-50L Absolute Maximum Ratings Ta = 25 Parameter Non-repetitive inductive turn-off energy Repetitive inductive turn-off energy Repetitive peak drain to input current Continuous forward current Junction to mounting base Conditions IDM = 15 A; RIS 100 Ù Symbol EDSM EDRM IDIRM IS Rth j-mb Transistors IC Rating 200 20 50 15 2.5 to 3.1 Unit mJ mJ mA A K/W 100 Ù; Tmb 95 ;IDM = RIS 4 A; VDD 20 V;f = 250 Hz RIS = 0 Ù; tp 1 ms VIS = VPS = VFS = 0 V Electrical Characteristics Ta = 25 Parameter Drain-source clamping voltage Drain-source clamping voltage Zero input voltage drain current Drain source leakage current Drain source leakage current Drain-source on-state resistance (VIS=7V) (VIS=5V) Overload threshold energy Response time Threshold junction temperature Forward transconductance EDS(TO) td sc Tj(TO) gfs Symbol V(CL)DSR V(CL)DSR IDSS IDSR IDSR RDS(ON) Testconditons RIS = 100 Ù; ID = 10 mA RIS = 100 Ù; IDM = 1 A; tp 0.01 VDS = 12 V; VIS = 0 V VDS = 50 V; RIS = 100 Ù; VDS = 40 V; RIS = 100 Ù;Tj = 125 IDM = 7.5 A;tp 300 ìs; d 0.01 10 mH;RI 10 mH;RI 0.65 300 ìs;d Min 50 50 0.5 1 10 75 95 150 375 150 5 9 25 40 0.2 1.5 Tj = 150 Protection clamp voltage Forward voltage Reverse recovery time Input threshold voltage Input current Input clamp voltage V(CL)PS VSDS trr VIS(TO) IIS V(CL)IS VDS = 5 V; ID = 1 mA Tmb = 150 VIS = 10 V II= 1 mA VPS = 5 V II = 5 mA; Input resistance RISL Tmb = 150 VPS = 10 V II = 5 mA; Tmb = 150 11 1.0 0.5 10 13 55 95 35 60 100 1.5 2.0 V V nA V Ù Ù Ù Ù IP = 1.35 mA IS = 15 A; VIS = VPS = VFS = 0 V;tp = 300 ìs 1.0 11 13 1.0 1.5 2.5 0.35 3.5 S A A mA V V V V Typ Max 65 70 10 20 100 100 125 Unit V V ìA ìA ìA mÙ mÙ mJ ìs VDD = 13 V; VIS = 10 V(L 2 kÙ) VDD = 13 V; VIS = 10 V(L 2 kÙ) VPS = VPSN; RI A 2 kÙ from ID VDS = 10 V; IDM = 7.5 A tp 0.01 VIS = 5 V VIS = 10 V 300 ìs;d Drain current (VDS = 13 V) Protection supply current Protection reset voltage ID IPS, VPSR VPS = 5 V 2 www.kexin.com.cn SMD Type KUK114-50L Electrical Characteristics Ta = 25 Parameter internal overvoltage clamping internal overload protection Turn-on delay time Rise time Turn-off delay time Fall time Input capacitance Output capacitance Reverse transfer capacitance Protection supply pin capacitance Flag pin capacitance Flag voltage Flag saturation current Flag leakage current Protection supply threshold voltage Flag clamping voltage Suitable external pull-up resistance Symbol RIS RI td on tr td off tf Ciss Coss Crss Cpso Cfso VFS IFSS IFS VPSF V(CL)FS RF Transistors IC Testconditons RI = RIS = Ù; VDS > 30 V Ù; VII = 5 V VII = 10 V VDD = 15 V; VIS: 0 V Þ 10 V Min 100 1 2 Typ Max Unit Ù kÙ kÙ 8 13 ns ns ns ns 600 400 80 pF pF pF pF pF 0.4 V mA 10 ìA V V 50 100 kÙ kÙ VDD = 15 V; VIS: 10 V 0V 100 45 VDS = 25 V; VIS = 0 V VDS = 25 V; VIS = 0 V VDS = 25 V; VIS = 0 V VPS = 10 V VFS = 10 V; VPS = 0 V IF = 1.6 mA VFS = 10 V VFS = 10 V VFF = 5 V; RF = 3 KÙ IF = 1 mA; VPS = 0 V VFF =5 V VFF =10 V 2.5 11 1 2 415 275 55 30 20 0.15 15 3.3 13 10 20 4 www.kexin.com.cn 3