AA2214QBS-D-AMT

2.2x1.4mm SURFACE MOUNT LED LAMP Part Number: AA2214QBS/D-AMT ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Blue Description The Blue source color devices are made with InGaN Light Emitting Diode. Static electricity and surge damage the LEDS. It is recommended to use a wrist band or anti-electrostatic glove when handling the LEDs. All devices, equipment and machinery must be electrically grounded. Features High reliability LED package. 2.2mm x 1.4mm, 1.3mm high. Low power consumption. Available on tape and reel. Package : 2000pcs / reel. Moisture sensitivity level : level 3. RoHS compliant. Applications Traffic signaling. Backlighting (illuminated advertising , general lighting). Interior and exterior automotive lighting. Substitution of micro incandescent lamps. Reading lamps. Signal and symbol luminaire for orientation. Marker lights (e.g. Steps, exit ways, etc). Decorative and entertainment lighting. Indoor and outdoor commercial and residential architectural lighting. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.2(0.008") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAL4009 APPROVED: WYNEC REV NO: V.1 CHECKED: Allen Liu DATE: NOV/22/2010 DRAWN: C.H.HAN PAGE: 1 OF 7 ERP: 1201007405 Handling Precautions Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic significantly reduces thermal stress, it is more susceptible to damage by external mechanical force. As a result, special handling precautions need to be observed during assembly using silicone encapsulated LED products. Failure to comply might lead to damage and premature failure of the LED. 1. Handle the component along the side surfaces by using forceps or appropriate tools. 2. Do not directly touch or handle the silicone lens surface. It may damage the internal circuitry. 3. Do not stack together assembled PCBs containing exposed LEDs. Impact may scratch the silicone lens or damage the internal circuitry. 4. The outer diameter of the SMD pickup nozzle should not exceed the size of the LED to prevent air leaks. The inner diameter of the nozzle should be as large as possible. 5. A pliable material is suggested for the nozzle tip to avoid scratching or damaging the LED surface during pickup. 6. The dimensions of the component must be accurately programmed in the pick-and-place machine to insure precise pickup and avoid damage during production. SPEC NO: DSAL4009 APPROVED: WYNEC REV NO: V.1 CHECKED: Allen Liu DATE: NOV/22/2010 DRAWN: C.H.HAN PAGE: 2 OF 7 ERP: 1201007405 Selection Guide Part No. Dice Lens Type Code. M AA2214QBS/D-AMT Blue (InGaN) Water Clear N P Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%. Iv (mcd) [2] @ 20mA Min. 80 120 200 Max. 120 200 300 Viewing Angle [1] 2θ1/2 120° Absolute Maximum Ratings at Ta=25°C Parameter Power dissipation Junction temperature Reverse Voltage Operating Temperature Storage Temperature DC Forward Current[1] Peak Forward Current [2] Electrostatic Discharge Threshold (HBM) Thermal Resistance (Junction/ambient) [1] Rth j-a Symbol PD TJ VR Top Tstg IF IFM Value 120 110 5 -40 To +100 -40 To +110 30 150 250 250 Unit mW °C V °C °C mA mA V °C/W N otes: 1. Rth(j-a) Results from mounting on PC board FR4 (pad size≥ 16 mm 2 per pad), 2. 1/10 Duty Cycle, 0.1ms Pulse Width. Electrical / Optical Characteristics at Ta=25°C Parameter Wavelength at peak emission IF=20mA Symbol λ peak 1B 2A Dominant Wavelength IF=20mA λ dom [1] 2B 3A 3B Reverse Current (VR = 5V) Spectral bandwidth at 50%Φ Forward Voltage REL MAX Value Code. Min. Typ. 468 461 464 467 469 471 468 471 473 475 477 50 25 3.3 0.05 0.03 -2.5 4.0 Max. Unit nm nm IR IF=20mA Δλ VF [2] TC λ peak TC λ dom TCV uA nm V nm/ ° C nm/ ° C mV/ ° C IF=20mA Temperature coefficient of λ peak IF=20mA, -10 ° C≤ T≤100 ° C Temperature coefficient of λ dom IF=20mA, -10 ° C≤ T≤100 ° C Temperature coefficient of VF IF=20mA, -10 ° C≤ T≤100 ° C Notes: 1.The dominant Wavelength (λ d) above is the setup value of the sorting machine. (Tolerance λ d : ±1nm. ) 2. Forward Voltage: +/-0.1V. SPEC NO: DSAL4009 APPROVED: WYNEC REV NO: V.1 CHECKED: Allen Liu DATE: NOV/22/2010 DRAWN: C.H.HAN PAGE: 3 OF 7 ERP: 1201007405 Blue AA2214QBS/D-AMT SPEC NO: DSAL4009 APPROVED: WYNEC REV NO: V.1 CHECKED: Allen Liu DATE: NOV/22/2010 DRAWN: C.H.HAN PAGE: 4 OF 7 ERP: 1201007405 AA2214QBS/D-AMT Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension Tape Dimensions (Units : mm) SPEC NO: DSAL4009 APPROVED: WYNEC REV NO: V.1 CHECKED: Allen Liu DATE: NOV/22/2010 DRAWN: C.H.HAN PAGE: 5 OF 7 ERP: 1201007405 PACKING & LABEL SPECIFICATIONS AA2214QBS/D-AMT SPEC NO: DSAL4009 APPROVED: WYNEC REV NO: V.1 CHECKED: Allen Liu DATE: NOV/22/2010 DRAWN: C.H.HAN PAGE: 6 OF 7 ERP: 1201007405 Reliability Test Items And Conditions The reliability of products shall be satisfied with items listed below Lot Tolerance Percent Defective (LTPD) : 10% Test Times / Number of Cycles Damaged 1,000 h 0 / 22 No. Test Item Standards Test Condition 1 Continuous operating test EIAJED4701/100(101) - Ta =25°C ,IF = maximum rated current* 2 High Temp. operating test Ta = 100°C IF = maximum rated current* 1,000 h 0 / 22 3 Low Temp. operating test Ta = -40°C, IF = maximum rated current* 1,000 h 0 / 22 4 High temp. storage test EIAJEDTa = maximum rated storage temperature 4701/100(201) EIAJED4701/100(202) EIAJED4701/100(103) EIAJED4701/100(102) EIAJED4701/100(301) Ta = -40°C 1,000 h 0 / 22 5 Low temp. storage test 1,000 h 0 / 22 6 High temp. & humidity storage test Ta = 60°C, RH = 90% Ta = 60°C, RH = 90% IF = maximum rated current* Moisture soak : 30°C,70% RH, 72h Preheat : 150~180°C(120s max.) Soldering temp : 260°C(10s) Ta = -40°C(15min) ~ 100°C(15min) IF = derated current at 100°C Ta = -40°C(15min) ~ maximum rated storage temperature(15min) C = 100pF , R2 = 1.5KΩ V = 250V a = 196m/s² , f = 100~2KHz , t = 48min for all xyz axes 1,000 h 0 / 22 7 High temp. & humidity operating test 1,000 h 0 / 22 8 Soldering reliability test 3 times 0 / 18 9 Thermal shock operating test 1,000 cycles 0 / 22 10 Thermal shock test EIAJED4701/100(304) - 1,000 cycles Once each Polarity 4 times 0 / 22 11 Electric Static Discharge (ESD) 0 / 22 12 Vibration test 0 / 22 * : Refer to forward current vs. derating curve diagram Failure Criteria Items luminous Intensity Forward Voltage Reverse Current High temp. storage test Symbols Conditions lv VF IR IF = 20mA IF = 20mA VR = Maximum Rated Reverse Voltage Failure Criteria Testing Min. Value