AA3528SESK

3.5x2.8mm SURFACE MOUNT LED LAMP Part Number: AA3528SESK Super Bright Orange Features Description z Single color. The Super Bright Orange device is made with AlGaInP (on z Suitable for all SMT assembly and solder process. GaAs substrate) light emitting diode chip. z Available on tape and reel. z Ideal for backlighting. z Package : 2000pcs / reel. z Moisture sensitivity level : level 3. z RoHS compliant. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25(0.01") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4.The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAL0869 REV NO: V.4A DATE: AUG/31/2012 PAGE: 1 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: D.M.Su ERP: 1201006725 Handling Precautions Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic significantly reduces thermal stress, it is more susceptible to damage by external mechanical force. As a result, special handling precautions need to be observed during assembly using silicone encapsulated LED products. Failure to comply might lead to damage and premature failure of the LED. 1. Handle the component along the side surfaces by using forceps or appropriate tools. 2. Do not directly touch or handle the silicone lens surface. It may damage the internal circuitry. 3. Do not stack together assembled PCBs containing exposed LEDs. Impact may scratch the silicone lens or damage the internal circuitry. 4.1. The inner diameter of the SMD pickup nozzle should not exceed the size of the LED to prevent air leaks. 4.2. A pliable material is suggested for the nozzle tip to avoid scratching or damaging the LED surface during pickup. 4.3. The dimensions of the component must be accurately programmed in the pick-and-place machine to insure precise pickup and avoid damage during production. 5. As silicone encapsulation is permeable to gases, some corrosive substances such as H2S might corrode silver plating of leadframe. Special care should be taken if an LED with silicone encapsulation is to be used near such substances. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAL0869 REV NO: V.4A DATE: AUG/31/2012 PAGE: 2 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: D.M.Su ERP: 1201006725 Selection Guide Part No. Dice Super Bright Orange (AlGaInP) AA3528SESK Iv (mcd) [2] @ 20mA Lens Type Water Clear Min. Typ. 200 350 *120 *230 Viewing Angle [1] 2θ1/2 120° Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%. *Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. λpeak Peak Wavelength Super Bright Orange λD [1] Dominant Wavelength Δλ1/2 Max. Units Test Conditions 610 nm IF=20mA Super Bright Orange 601 nm IF=20mA Spectral Line Half-width Super Bright Orange 29 nm IF=20mA C Capacitance Super Bright Orange 15 pF VF=0V;f=1MHz VF [2] Forward Voltage Super Bright Orange 2.1 2.5 V IF=20mA IR Reverse Current Super Bright Orange 10 uA VR=5V Notes: 1.Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. 3. Wavelength value is traceable to the CIE127-2007 compliant national standards. Absolute Maximum Ratings at TA=25°C Parameter Super Bright Orange Units Power dissipation 75 mW DC Forward Current 30 mA Peak Forward Current [1] 195 mA 5 V Reverse Voltage Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAL0869 REV NO: V.4A DATE: AUG/31/2012 PAGE: 3 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: D.M.Su ERP: 1201006725 Super Bright Orange AA3528SESK SPEC NO: DSAL0869 REV NO: V.4A DATE: AUG/31/2012 PAGE: 4 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: D.M.Su ERP: 1201006725 AA3528SESK Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension Tape Dimensions (Units : mm) SPEC NO: DSAL0869 REV NO: V.4A DATE: AUG/31/2012 PAGE: 5 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: D.M.Su ERP: 1201006725 PACKING & LABEL SPECIFICATIONS AA3528SESK SPEC NO: DSAL0869 REV NO: V.4A DATE: AUG/31/2012 PAGE: 6 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: D.M.Su ERP: 1201006725