AA3529SYS-L

3.5x2.8 mm SMD CHIP LED LAMP Part Number: AA3529SYS/L Super Bright Yellow PRELIMINARY SPEC Features SINGLE COLOR. SUITABLE FOR ALL SMT ASSEMBLY AND SOLDER PROCESS. AVAILABLE ON TAPE AND REEL. IDEAL FOR BACKLIGHTING. WHITE SMD PACKAGE, SILICONE RESIN. LOW THERMAL RESISTANCE. PACKAGE: 1500PCS / REEL. MOISTURE SENSITIVITY LEVEL : LEVEL 2a. RoHS COMPLIANT. Description The source color devices are made with AlInGaP Light Emitting Diode. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25(0.01") unless otherwise noted. 3. Specifications are subject to change without notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAH5250 APPROVED: WYNEC REV NO: V.4 CHECKED: Allen Liu DATE: JAN/14/2008 DRAWN: R.CHEN PAGE: 1 OF 6 ERP: 1201002971 Handling Precautions Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic significantly reduces thermal stress, it is more susceptible to damage by external mechanical force. As a result, special handling precautions need to be observed during assembly using silicone encapsulated LED products. Failure to comply might leads to damage and premature failure of the LED. 1. Handle the component along the side surfaces by using forceps or appropriate tools. 2. Do not directly touch or handle the silicone lens surface. It may damage the internal circuitry. 3. Do not stack together assembled PCBs containing exposed LEDs. Outside impact may scratch the silicone lens or damage the internal circuitry. 4. The outer diameter of the SMD pickup nozzle should not exceed the size of the LED to prevent air leaks. The inner diameter of the nozzle should be as large as possible. 5. A pliable material is suggested for the nozzle tip to avoid scratching or damaging the LED surface during pickup. 6. The dimensions of the component must be accurately programmed in the pick-and-place machine to insure precise pickup and avoid damage during production. SPEC NO: DSAH5250 APPROVED: WYNEC REV NO: V.4 CHECKED: Allen Liu DATE: JAN/14/2008 DRAWN: R.CHEN PAGE: 2 OF 6 ERP: 1201002971 Selection Guide Part No. Dice Lens Type Iv (mcd) [2] @ 150mA Min. AA3529SYS/L Super Bright Yellow (AlInGaP) WATER CLEAR 1600 Typ. 3000 Φv (mlm) [2] @ 150mA Min. 3000 Typ. 6000 Viewing Angle [1] 2θ1/2 120° Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value. 2. Luminous intensity / luminous flux: +/-15%. Electrical / Optical Characteristics at TA=25°C Symbol λpeak λD [1] Δλ1/2 C VF [2] IR Parameter Peak Wavelength Dominant Wavelength Spectral Line Half-width Capacitance Forward Voltage Reverse Current Device Super Bright Yellow Super Bright Yellow Super Bright Yellow Super Bright Yellow Super Bright Yellow Super Bright Yellow Typ. 590 590 20 20 2.8 3.2 10 Max. Units nm nm nm pF V uA Test Conditions IF=150mA IF=150mA IF=150mA VF=0V;f=1MHz IF=150mA VR=5V Notes: 1.Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. Absolute Maximum Ratings at TA=25°C Parameter Power dissipation DC Forward Current Peak Forward Current [1] Reverse Voltage Operating Temperature Storage Temperature Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. Super Bright Yellow 480 150 200 5 -40°C To +85°C -40°C To +85°C Units mW mA mA V SPEC NO: DSAH5250 APPROVED: WYNEC REV NO: V.4 CHECKED: Allen Liu DATE: JAN/14/2008 DRAWN: R.CHEN PAGE: 3 OF 6 ERP: 1201002971 yalin Super Bright Yellow 數位簽署者：yalin DN：cn=yalin, o, ou, email=sjhou@cn. kingbright.com, c= 日期︰2008.01.15 13:21:08 +08'00' AA3529SYS/L SPEC NO: DSAH5250 APPROVED: WYNEC REV NO: V.4 CHECKED: Allen Liu DATE: JAN/14/2008 DRAWN: R.CHEN PAGE: 4 OF 6 ERP: 1201002971 AA3529SYS/L Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Tape Specifications (Units : mm) SPEC NO: DSAH5250 APPROVED: WYNEC REV NO: V.4 CHECKED: Allen Liu DATE: JAN/14/2008 DRAWN: R.CHEN PAGE: 5 OF 6 ERP: 1201002971 PACKING & LABEL SPECIFICATIONS AA3529SYS/L SPEC NO: DSAH5250 APPROVED: WYNEC REV NO: V.4 CHECKED: Allen Liu DATE: JAN/14/2008 DRAWN: R.CHEN PAGE: 6 OF 6 ERP: 1201002971