AAA5060SUREVGEC

5.0mm x 6.0mm BI-COLOR SURFACE MOUNT LED LAMP ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES AAA5060SUREVGEC HYPER RED / GREEN Features CHIPS CAN BE CONTROLLED SEPARATELY. SUITABLE FOR ALL SMT ASSEMBLY AND SOLDER PROCESS. AVAILABLE ON TAPE AND REEL. PACKAGE: 500PCS / REEL. RoHS COMPLIANT. Description The Hyper Red source color devices are made with DH InGaAlP on GaAs substrate Light Emitting Diode. The Green source color devices are made with InGaN on SiC Light Emitting Diode. Static electricity and surge damage the LEDS. It is recommended to use a wrist band or anti-electrostatic glove when handling the LEDs. All devices, equipment and machinery must be electrically grounded. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25(0.01") unless otherwise noted. 3. Specifications are subject to change without notice. SPEC NO: DSAD0905 APPROVED: J. Lu REV NO: V.5 CHECKED: Allen Liu DATE: MAR/14/005 DRAWN: B.H.LI PAGE: 1 OF 5 ERP: 1201000783 Selection Guide Part No. Dice Lens Type Iv (mcd) @50mA*30 mA Min. HYPER RED (InGaAlP) AAA5060SUREVGEC WATER CLEAR GREEN (InGaN) *280 *600 380 Typ. 700 Viewing Angle 2 θ 1/2 100° Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value. 2. * Luminous intensity with asterisk is measured at 30mA. Electrical / Optical Characteristics at TA=25°C Symbol λpeak λD ∆λ1/2 C VF IR Parameter Peak Wavelength Dominant Wavelength Spectral Line Half-width Capacitance Forward Voltage Reverse Current Device Hyper Red Green Hyper Red Green Hyper Red Green Hyper Red Green Hyper Red Green All Typ. 640 518 630 525 25 36 45 50 1.9 3.5 2.5 4.5 10 Max. Units nm nm nm pF V uA Test Conditions IF=20mA IF=20mA IF=20mA VF=0V;f=1MHz IF=20mA VR = 5V Absolute Maximum Ratings at TA=25°C Parameter Power dissipation DC Forward Current Peak Forward Current [1] Reverse Voltage Operating / Storage Temperature Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. Hyper Red 125 50 200 5 Green 135 30 150 5 -40°C To +85°C Units mW mA mA V SPEC NO: DSAD0905 APPROVED: J. Lu REV NO: V.5 CHECKED: Allen Liu DATE: MAR/14/005 DRAWN: B.H.LI PAGE: 2 OF 5 ERP: 1201000783 AAA5060SUREVGEC Hyper Red SPEC NO: DSAD0905 APPROVED: J. Lu REV NO: V.5 CHECKED: Allen Liu DATE: MAR/14/005 DRAWN: B.H.LI PAGE: 3 OF 5 ERP: 1201000783 Green SPEC NO: DSAD0905 APPROVED: J. Lu REV NO: V.5 CHECKED: Allen Liu DATE: MAR/14/005 DRAWN: B.H.LI PAGE: 4 OF 5 ERP: 1201000783 AAA5060SUREVGEC Recommended Soldering Pattern (Units : mm) Tape Specifications (Units : mm) If special sorting is required (e.g. binning based on forward voltage, luminous intensity, or wavelength), the typical accuracy of the sorting process is as follows: 1. Wavelength: +/-1nm 2. Luminous Intensity: +/-15% 3. Forward Voltage: +/-0.1V Note: Accuracy may depend on the sorting parameters. SPEC NO: DSAD0905 APPROVED: J. Lu REV NO: V.5 CHECKED: Allen Liu DATE: MAR/14/005 DRAWN: B.H.LI PAGE: 5 OF 5 ERP: 1201000783