AAAF5051-04

5.0mm x 5.0mm FULL-COLOR SURFACE MOUNT LED LAMP ATTENTION Part Number: AAAF5051-04 OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Blue Reddish-Orange Green Features Descriptions z Chips can be controlled separately. z The Blue source color devices are made with InGaN on z Suitable for all SMT assembly and solder process. z Available on tape and reel. Al2O3 substrate Light Emitting Diode. z The Reddish-Orange source color devices are made with z White SMD package, silicone resin. z Package: 500pcs / reel. AlGaInP on AlN substrate Light Emitting Diode. z The Green source color devices are made with InGaN on z Moisture sensitivity level : level 3. z RoHS compliant. Al2O3 substrate Light Emitting Diode. z Electrostatic discharge and power surge could damage the LEDs. z It is recommended to use a wrist band or antielectrostatic glove when handling the LEDs. z All devices, equipments and machineries must be electrically grounded. Package Dimensions R Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.15[±0.006]unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAM7047 REV NO: V.4B DATE: SEP/16/2014 PAGE: 1 OF 9 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP : 1201008410 Handling Precautions Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic significantly reduces thermal stress, it is more susceptible to damage by external mechanical force. As a result, special handling precautions need to be observed during assembly using silicone encapsulated LED products. Failure to comply might lead to damage and premature failure of the LED. 1. Handle the component along the side surfaces by using forceps or appropriate tools. 2. Do not directly touch or handle the silicone lens surface. It may damage the internal circuitry. 3. Do not stack together assembled PCBs containing exposed LEDs. Impact may scratch the silicone lens or damage the internal circuitry. 4.1. The inner diameter of the SMD pickup nozzle should not exceed the size of the LED to prevent air leaks. 4.2. A pliable material is suggested for the nozzle tip to avoid scratching or damaging the LED surface during pickup. 4.3. The dimensions of the component must be accurately programmed in the pick-and-place machine to insure precise pickup and avoid damage during production. 5. As silicone encapsulation is permeable to gases, some corrosive substances such as H2S might corrode silver plating of leadframe. Special care should be taken if an LED with silicone encapsulation is to be used near such substances. SPEC NO: DSAM7047 REV NO: V.4B DATE: SEP/16/2014 PAGE: 2 OF 9 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP : 1201008410 Selection Guide Part No. Dice Lens Type Blue (InGaN) AAAF5051-04 Water Clear Reddish-Orange (AlGaInP) Green (InGaN) Iv (mcd) [2] @ 150mA Φv (lm) [2] @ 150mA* Viewing Angle [1] Min. Typ. Min. Typ. 1000 1500 4.2 6 2700 3200 10 12 5000 6300 17 20 2θ1/2 120° Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%.*LEDs are binned according to their luminous flux. 3. Luminous intensity/ luminous Flux value is traceable to the CIE127-2007 compliant national standards. Absolute Maximum Ratings at Ta=25°C Parameter Power dissipation Junction temperature Symbol Device Blue 0.6 PD Reddish-Orange 0.45 Green 0.6 Blue 110 Reddish-Orange 110 Green 110 TJ Value Unit Test Conditions W IF=150mA IF=150mA IF=150mA °C IF=150mA IF=150mA IF=150mA -40 To +85 °C IF=150mA IF=150mA IF=150mA -40 To +85 °C IF=150mA IF=150mA IF=150mA mA IF=150mA IF=150mA IF=150mA mA IF=150mA IF=150mA IF=150mA °C/W IF=150mA IF=150mA IF=150mA °C/W IF=150mA IF=150mA IF=150mA uA VR=5V Blue Operating Temperature Top Reddish-Orange Green Blue Storage Temperature Tstg Reddish-Orange Green DC Forward Current [1] Peak Forward Current [2] Thermal resistance Thermal resistance Reverse Current IF IFM Rth j-a Rth j-s IR Blue 150 Reddish-Orange 150 Green 150 Blue 300 Reddish-Orange 300 Green 300 Blue 220 Reddish-Orange 270 Green 200 Blue 25 Reddish-Orange 40 Green 33 Blue 10 Reddish-Orange 10 Green 10 Notes: 1. Results from mounting on Aluminum Board. 2. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAM7047 REV NO: V.4B DATE: SEP/16/2014 PAGE: 3 OF 9 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP : 1201008410 Electrical / Optical Characteristics at Ta=25°C Value Parameter Symbol Device Unit Min. Wavelength at peak emission IF=150mA Typ. Blue 452 Reddish-Orange 635 Wavelength at peak emission IF=150mA Green 515 Dominant Wavelength IF=150mA Blue 460 Reddish-Orange 624 Dominant Wavelength IF=150mA Green 525 Spectral Line Half-width IF=150mA Blue 25 Reddish-Orange 20 Green 30 Wavelength at peak emission IF=150mA Dominant Wavelength IF=150mA Spectral Line Half-width IF=150mA λ peak λ dom [1] Δλ1/2 Spectral Line Half-width IF=150mA Forward Voltage IF=150mA Forward Voltage IF=150mA Forward Voltage IF=150mA VF [2] 4.0 Reddish-Orange 2.0 2.5 3.0 Green 3.0 3.5 4.0 5 Green 5 Blue 0.12 Reddish-Orange 0.09 Temperature coefficient of λ peak IF=150mA, -10 ° C≤ T≤100 ° C Green 0.13 Temperature coefficient of λ dom IF=150mA, -10 ° C≤ T≤100 ° C Blue 0.1 Reddish-Orange 0.03 Temperature coefficient of λ dom IF=150mA, -10 ° C≤ T≤100 ° C Green 0.11 Temperature coefficient of VF IF=150mA, -10 ° C≤ T≤100 ° C Blue -2.3 Reddish-Orange -2.7 Green -3.9 Temperature coefficient of λ peak IF=150mA, -10 ° C≤ T≤100 ° C Temperature coefficient of λ dom IF=150mA, -10 ° C≤ T≤100 ° C Temperature coefficient of VF IF=150mA, -10 ° C≤ T≤100 ° C TC λ peak TC λ dom TCV Temperature coefficient of VF IF=150mA, -10 ° C≤ T≤100 ° C nm 3.5 Reddish-Orange Temperature coefficient of λ peak IF=150mA, -10 ° C≤ T≤100 ° C nm 3.0 5 VR nm Blue Blue Reverse Voltage Max. V V nm/ ° C nm/ ° C mV/ ° C Notes: 1.Wavelength: +/-1nm. 2.Forward Voltage: +/-0.2V. 3.Wavelength value is traceable to the CIE127-2007 compliant national standards. 4.Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. SPEC NO: DSAM7047 REV NO: V.4B DATE: SEP/16/2014 PAGE: 4 OF 9 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP : 1201008410 BLUE GREEN REDDISH-ORANGE AAAF5051-04 Blue SPEC NO: DSAM7047 REV NO: V.4B DATE: SEP/16/2014 PAGE: 5 OF 9 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP : 1201008410 Reddish-orange SPEC NO: DSAM7047 REV NO: V.4B DATE: SEP/16/2014 PAGE: 6 OF 9 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP : 1201008410 Green SPEC NO: DSAM7047 REV NO: V.4B DATE: SEP/16/2014 PAGE: 7 OF 9 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP : 1201008410 AAAF5051-04 Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Reel Dimension Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Tape Specifications (Units : mm) SPEC NO: DSAM7047 REV NO: V.4B DATE: SEP/16/2014 PAGE: 8 OF 9 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP : 1201008410 PACKING & LABEL SPECIFICATIONS AAAF5051-04 Terms and conditions for the usage of this document 1.The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2.The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3.When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4.The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5.The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6.All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAM7047 REV NO: V.4B DATE: SEP/16/2014 PAGE: 9 OF 9 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP : 1201008410