ACDA02-41EWA-F01

SURFACE MOUNT DISPLAY Part Number: ACDA02-41EWA-F01 High Efficiency Red Features Description z 0.2 inch digit height. The High Efficiency Red source color devices are made with z Low current operation. Gallium Arsenide Phosphide on Gallium Phosphide Orange z Excellent character appearance. Light Emitting Diode. z Mechanically rugged. z Package :300pcs / reel. z Gray face, white segment. z Moisture sensitivity level : level 2a. z RoHS compliant. Package Dimensions& Internal Circuit Diagram Notes: 1. All dimensions are in millimeters (inches), Tolerance is ±0.25(0.01")unless otherwise noted. 2. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 3.The gap between the reflector and PCB shall not exceed 0.25mm. SPEC NO: DSAG0576 REV NO: V.6A DATE: DEC/29/2015 PAGE: 1 OF 5 APPROVED: Wynec CHECKED: Joe Lee DRAWN: F.T.Liu ERP: 1352000355 Selection Guide Part No. Emitting Color (Material) High Efficiency Red (GaAsP/GaP) ACDA02-41EWA-F01 Iv (ucd) [1] @ 10mA Lens Type White Diffused Min. Typ. 1400 3200 *360 *950 Description Common Anode, Rt. Hand Decimal. Notes: 1. Luminous intensity / luminous Flux: +/-15%. * Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Emitting Color Typ. λpeak Peak Wavelength High Efficiency Red λD [1] Dominant Wavelength Δλ1/2 Max. Units Test Conditions 627 nm IF=10mA High Efficiency Red 617 nm IF=10mA Spectral Line Half-width High Efficiency Red 45 nm IF=10mA C Capacitance High Efficiency Red 15 pF VF=0V;f=1MHz VF [2] Forward Voltage High Efficiency Red 1.9 2.5 V IF=10mA IR Reverse Current High Efficiency Red 10 uA VR=5V Notes: 1. Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. 3. Wavelength value is traceable to the CIE127-2007 compliant national standards. 4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25°C Parameter Values Units Power dissipation 75 mW DC Forward Current 30 mA Peak Forward Current [1] 160 mA 5 V Reverse Voltage Operating / Storage Temperature -40°C To +85°C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAG0576 REV NO: V.6A DATE: DEC/29/2015 PAGE: 2 OF 5 APPROVED: Wynec CHECKED: Joe Lee DRAWN: F.T.Liu ERP: 1352000355 High Efficiency Red ACDA02-41EWA-F01 SPEC NO: DSAG0576 REV NO: V.6A DATE: DEC/29/2015 PAGE: 3 OF 5 APPROVED: Wynec CHECKED: Joe Lee DRAWN: F.T.Liu ERP: 1352000355 ACDA02-41EWA-F01 Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.15) Reel Dimension Tape Specifications (Units : mm) SPEC NO: DSAG0576 REV NO: V.6A DATE: DEC/29/2015 PAGE: 4 OF 5 APPROVED: Wynec CHECKED: Joe Lee DRAWN: F.T.Liu ERP: 1352000355 PACKING & LABEL SPECIFICATIONS ACDA02-41EWA-F01 Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAG0576 REV NO: V.6A DATE: DEC/29/2015 PAGE: 5 OF 5 APPROVED: Wynec CHECKED: Joe Lee DRAWN: F.T.Liu ERP: 1352000355