ACDC03-41SEKWA-F01

SURFACE MOUNT DISPLAY Part Number: ACDC03-41SEKWA-F01 Super Bright Orange Features 0.3 INCH DIGIT HEIGHT. LOW CURRENT OPERATION. EXCELLENT CHARACTER APPEARANCE. I.C. COMPATIBLE. MECHANICALLY RUGGED. PACKAGE :300PCS / REEL. GRAY FACE, WHITE SEGMENT. MOISTURE SENSITIVITY LEVEL : LEVEL 4. RoHS COMPLIANT. Description The Super Bright Orange device is made with InGaAlP (on GaAs substrate) light emitting diode chip. Package Dimensions& Internal Circuit Diagram 1. All dimensions are in millimeters (inches), Tolerance is ±0.25(0.01")unless otherwise noted. 2. Specifications are subject to change without notice. 3.The gap between the reflector and PCB shall not exceed 0.25mm. SPEC NO: DSAG0233 APPROVED: WYNEC REV NO: V.6 CHECKED: Joe Lee DATE: JUN/13/2007 DRAWN: Y.H.CHEN PAGE: 1 OF 5 ERP: 1352000333 Selection Guide Part No. Dice Lens Type Iv (ucd) [1] @ 10mA Min. ACDC03-41SEKWA-F01 Super Bright Orange (InGaAlP) Note: 1. Luminous intensity/ luminous Flux: +/-15%. Description Typ. 46000 Common Cathode, Rt. Hand Decimal. WHITE DIFFUSED 12000 Electrical / Optical Characteristics at TA=25°C Symbol λpeak λD [1] Δλ1/2 C VF [2] IR Parameter Peak Wavelength Dominant Wavelength Spectral Line Half-width Capacitance Forward Voltage Reverse Current Device Super Bright Orange Super Bright Orange Super Bright Orange Super Bright Orange Super Bright Orange Super Bright Orange Typ. 610 601 29 15 2.1 2.5 10 Max. Units nm nm nm pF V uA Test Conditions IF=20mA IF=20mA IF=20mA VF=0V;f=1MHz IF=20mA VR=5V Notes: 1.Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. Absolute Maximum Ratings at TA=25°C Parameter Power dissipation DC Forward Current Peak Forward Current [1] Reverse Voltage Operating / Storage Temperature Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. Super Bright Orange 75 30 195 5 -40°C To +85°C Units mW mA mA V SPEC NO: DSAG0233 APPROVED: WYNEC REV NO: V.6 CHECKED: Joe Lee DATE: JUN/13/2007 DRAWN: Y.H.CHEN PAGE: 2 OF 5 ERP: 1352000333 Super Bright Orange ACDC03-41SEKWA-F01 SPEC NO: DSAG0233 APPROVED: WYNEC REV NO: V.6 CHECKED: Joe Lee DATE: JUN/13/2007 DRAWN: Y.H.CHEN PAGE: 3 OF 5 ERP: 1352000333 ACDC03-41SEKWA-F01 Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.15) Reel Dimension Tape Specifications (Units : mm) SPEC NO: DSAG0233 APPROVED: WYNEC REV NO: V.6 CHECKED: Joe Lee DATE: JUN/13/2007 DRAWN: Y.H.CHEN PAGE: 4 OF 5 ERP: 1352000333 PACKING & LABEL SPECIFICATIONS ACDC03-41SEKWA-F01 SPEC NO: DSAG0233 APPROVED: WYNEC REV NO: V.6 CHECKED: Joe Lee DATE: JUN/13/2007 DRAWN: Y.H.CHEN PAGE: 5 OF 5 ERP: 1352000333