ACPSC04-41SYKWA

ACPSC04-41SYKWA Surface Mount Display DESCRIPTIONS



PACKAGE DIMENSIONS The Super Bright Yellow device is made with AlGaInP (on GaAs substrate) light emitting diode chip Electrostatic discharge and power surge could damage the LEDs It is recommended to use a wrist band or anti-electrostatic glove when handling the LEDs All devices, equipments and machineries must be electrically grounded FEATURES








0.4 inch character height Low current operation High contrast and light output Categorized for luminous intensity Mechanically rugged Gray face, white segment Package: 400 pcs / reel Moisture sensitivity level: 2a RoHS compliant RECOMMENDED SOLDERING PATTERN (units: mm; tolerance: ± 0.15) APPLICATIONS



Home and smart appliances Display time and digital combination Industrial and instrumental applications Numeric status ATTENTION Observe precautions for handling electrostatic discharge sensitive devices Notes: 1. All dimensions are in millimeters (inches), Tolerance is ±0.25(0.01") unless otherwise noted. 2. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 3. The gap between the reflector and PCB shall not exceed 0.25mm. SELECTION GUIDE Part Number ACPSC04-41SYKWA Emitting Color (Material) ■ Super Bright Yellow Iv (ucd) @ 10mA [1] Lens Type Description Min. Typ. 21000 46000 Common Cathode Rt. Hand Decimal White Diffused (AlGaInP) *5600 *12000 Notes: 1. Luminous intensity / luminous Flux: +/-15%. * Luminous intensity value is traceable to CIE127-2007 standards. © 2021 Kingbright. All Rights Reserved. Spec No: DSAG5000 / 1361000057 Rev No: V.13A Date: 04/12/2021 Page 1 / 4 ACPSC04-41SYKWA ELECTRICAL / OPTICAL CHARACTERISTICS at TA=25°C Value Parameter Symbol Wavelength at Peak Emission IF = 10mA Emitting Color Unit Typ. Max. λpeak Super Bright Yellow 590 - nm λdom [1] Super Bright Yellow 590 - nm Spectral Bandwidth at 50% Φ REL MAX IF = 10mA ∆λ Super Bright Yellow 20 - nm Capacitance C Super Bright Yellow 20 - pF Forward Voltage IF = 10mA VF [2] Super Bright Yellow 1.95 2.35 V Reverse Current (VR = 5V) IR Super Bright Yellow - 10 µA Dominant Wavelength IF = 10mA Notes: 1. The dominant wavelength (λd) above is the setup value of the sorting machine. (Tolerance λd : ±1nm. ) 2. Forward voltage: ±0.1V. 3. Wavelength value is traceable to CIE127-2007 standards. 4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. ABSOLUTE MAXIMUM RATINGS at TA=25°C Parameter Symbol Value Unit Power Dissipation PD 75 mW Reverse Voltage VR 5 V Junction Temperature Tj 115 °C Operating Temperature Top -40 to +85 °C Storage Temperature Tstg -40 to +85 °C DC Forward Current IF 30 mA IFM [1] 175 mA - 3000 V Peak Forward Current Electrostatic Discharge Threshold (HBM) Notes: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. 2. Relative humidity levels maintained between 40% and 60% in production area are recommended to avoid the build-up of static electricity – Ref JEDEC/JESD625-A and JEDEC/J-STD-033. © 2021 Kingbright. All Rights Reserved. Spec No: DSAG5000 / 1361000057 Rev No: V.13A Date: 04/12/2021 Page 2 / 4 ACPSC04-41SYKWA TECHNICAL DATA RELATIVE INTENSITY vs. WAVELENGTH Yellow Relative Intensity (a. u.) 100% Ta = 25 °C 80% 60% 40% 20% 0% 350 400 450 500 550 600 Wavelength (nm) 650 700 750 800 SUPER BRIGHT YELLOW Forward current (mA) Ta = 25 °C 16 12 8 4 1.8 1.9 2.0 2.1 Forward voltage (V) 2.2 2.5 Permissible forward current (mA) Luminous intensity normalised at 10 mA 20 0 1.7 Forward Current Derating Curve Luminous Intensity vs. Forward Current Ta = 25 °C 2.0 1.5 1.0 0.5 0.0 0 4 8 12 16 Forward current (mA) 20 REFLOW SOLDERING PROFILE for LEAD-FREE SMD PROCESS 50 Luminous Intensity vs. Ambient Temperature Luminous intensity normalised at Ta = 25 °C Forward Current vs. Forward Voltage 40 30 20 10 0 -40 -20 0 20 40 60 80 100 Ambient temperature (°C) 2.5 2.0 1.5 1.0 0.5 0.0 -40 -20 0 20 40 60 80 100 Ambient temperature (°C) TAPE SPECIFICATIONS (units: mm) REEL DIMENSION (units: mm) Notes: 1. Don't cause stress to the LEDs while it is exposed to high temperature. 2. The maximum number of reflow soldering passes is 2 times. 3. Reflow soldering is recommended. Other soldering methods are not recommended as they might cause damage to the product. © 2021 Kingbright. All Rights Reserved. Spec No: DSAG5000 / 1361000057 Rev No: V.13A Date: 04/12/2021 Page 3 / 4 ACPSC04-41SYKWA PACKING & LABEL SPECIFICATIONS CIRCUIT DESIGN NOTES 1. Protective current-limiting resistors may be necessary to operate the LEDs within the specified range. 2. LEDs mounted in parallel should each be placed in series with its own current-limiting resistor. 3. The driving circuit should be designed to protect the LED against reverse voltages and transient voltage spikes when the circuit is powered up or shut down. 4. The safe operating current should be chosen after considering the maximum ambient temperature of the operating environment. 5. Prolonged reverse bias should be avoided, as it could cause metal migration, leading to an increase in leakage current or causing a short circuit. PRECAUTIONARY NOTES 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. When any special process such as potting is required for LED assembly, please consult with Kingbright representative before proceeding. 7. All design applications should refer to Kingbright application notes available at https://www.KingbrightUSA.com/ApplicationNotes © 2021 Kingbright. All Rights Reserved. Spec No: DSAG5000 / 1361000057 Rev No: V.13A Date: 04/12/2021 Page 4 / 4