ACSA56-51PBWA/A

SURFACE MOUNT DISPLAY ATTENTION Part Number: ACSA56-51PBWA/A OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Blue Features Descriptions  0.56 inch digit height.  The Blue source color devices are made with InGaN on SiC Light Emitting Diode.  Low current operation.  Electrostatic discharge and power surge could damage  Excellent character appearance. the LEDs.  Mechanically rugged.  It is recommended to use a wrist band or anti-  Gray face,white segment. electrostatic glove when handling the LEDs.  Package: 400pcs/ reel.  All devices, equipments and machineries must be  Moisture sensitivity level : level 2a. electrically grounded.  RoHS compliant. Package Dimensions& Internal Circuit Diagram BLUE Notes: 1. All dimensions are in millimeters (inches), Tolerance is ±0.25(0.01")unless otherwise noted. 2. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 3. The gap between the reflector and PCB shall not exceed 0.25mm. SPEC NO: DSAM7136 REV NO: V.4B DATE: SEP/02/2014 PAGE: 1 OF 5 APPROVED: WYNEC CHECKED: Joe Lee DRAWN: Q.M.Chen ERP: 1351000712 Selection Guide Part No. Dice ACSA56-51PBWA/A Iv (ucd) [1] @ 10mA Lens Type Blue (InGaN) White Diffused Description Min. Typ. 1400 4000 Common Anode Units Test Conditions Notes: 1. Luminous intensity/ luminous Flux: +/-15%. 2. Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. Max. λpeak Peak Wavelength Blue 468 nm IF=20mA λD [1] Dominant Wavelength Blue 465 nm IF=20mA Δλ1/2 Spectral Line Half-width Blue 21 nm IF=20mA C Capacitance Blue 100 pF VF=0V;f=1MHz VF [2] Forward Voltage Blue 3.2 4.0 V IF=20mA IR Reverse Current Blue 10 uA VR=5V Notes: 1.Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. 3. Wavelength value is traceable to the CIE127-2007 compliant national standards. 4.Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25°C Parameter Blue Units Power dissipation 120 mW DC Forward Current 30 mA Peak Forward Current [1] 100 mA 5 V Reverse Voltage Operating / Storage Temperature -40°C To +85°C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAM7136 REV NO: V.4B DATE: SEP/02/2014 PAGE: 2 OF 5 APPROVED: WYNEC CHECKED: Joe Lee DRAWN: Q.M.Chen ERP: 1351000712 Blue ACSA56-51PBWA/A SPEC NO: DSAM7136 REV NO: V.4B DATE: SEP/02/2014 PAGE: 3 OF 5 APPROVED: WYNEC CHECKED: Joe Lee DRAWN: Q.M.Chen ERP: 1351000712 ACSA56-51PBWA/A Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.15) Reel Dimension Tape Specifications (Units : mm) SPEC NO: DSAM7136 REV NO: V.4B DATE: SEP/02/2014 PAGE: 4 OF 5 APPROVED: WYNEC CHECKED: Joe Lee DRAWN: Q.M.Chen ERP: 1351000712 PACKING & LABEL SPECIFICATIONS ACSA56-51PBWA/A Terms and conditions for the usage of this document 1.The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2.The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3.When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4.The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5.The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6.All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAM7136 REV NO: V.4B DATE: SEP/02/2014 PAGE: 5 OF 5 APPROVED: WYNEC CHECKED: Joe Lee DRAWN: Q.M.Chen ERP: 1351000712