AM2520YC09

AM2520YC09 Subminiature Solid State Lamp DESCRIPTION PACKAGE DIMENSIONS The Yellow source color devices are made with Gallium Arsenide Phosphide on Gallium Phosphide Yellow Light Emitting Diode FEATURES Subminiature package Z-bend lead Long life - solid state reliability Low package profile Moisture sensitivity level: 3 Package: 1000 pcs / reel RoHS compliant APPLICATIONS Backlight Status indicator Home and smart appliances Wearable and portable devices Healthcare applications RECOMMENDED SOLDERING PATTERN (units : mm; tolerance : ± 0.1) ATTENTION Observe precautions for handling electrostatic discharge sensitive devices Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25(0.01") unless otherwise noted. 3. Lead spacing is measured where the leads emerge from the package. 4. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 5. The device has a single mounting surface. The device must be mounted according to the specifications. SELECTION GUIDE Part Number AM2520YC09 Iv (mcd) @ 20mA [2] Emitting Color (Material) Lens Type ■ Yellow (CaAsP/GaP) Water Clear Viewing Angle [1] Min. Typ. 2θ1/2 20 50 20° Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity / luminous flux: +/-15%. 3. Luminous intensity value is traceable to CIE127-2007 standards. © 2017 Kingbright. All Rights Reserved. Spec No: DSAD1287 / 1202000759 Rev No: V.12B Date: 09/20/2017 Page 1 / 4 AM2520YC09 ELECTRICAL / OPTICAL CHARACTERISTICS at TA=25°C Parameter Symbol Emitting Color λpeak Value Unit Typ. Max. Yellow 590 - nm λdom [1] Yellow 588 - nm Spectral Bandwidth at 50% Φ REL MAX IF = 20mA Δλ Yellow 35 - nm Capacitance C Yellow 20 - pF Forward Voltage IF = 20mA VF [2] Yellow 2.1 2.5 V Reverse Current (VR = 5V) IR Yellow - 10 uA Wavelength at Peak Emission IF = 20mA Dominant Wavelength IF = 20mA Notes: 1. The dominant wavelength (λd) above is the setup value of the sorting machine. (Tolerance λd : ±1nm. ) 2. Forward voltage: ±0.1V. 3. Wavelength value is traceable to CIE127-2007 standards. 4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. ABSOLUTE MAXIMUM RATINGS at TA=25°C Parameter Symbol Value Unit Power Dissipation PD 75 mW Reverse Voltage VR 5 V Junction Temperature Tj 110 °C Operating Temperature Top -40 to +85 °C Storage Temperature Tstg -40 to +85 °C DC Forward Current IF 30 mA IFM [1] 140 mA - 8000 V Peak Forward Current Electrostatic Discharge Threshold (HBM) Notes: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. 2. Relative humidity levels maintained between 40% and 60% in production area are recommended to avoid the build-up of static electricity – Ref JEDEC/JESD625-A and JEDEC/J-STD-033. © 2017 Kingbright. All Rights Reserved. Spec No: DSAD1287 / 1202000759 Rev No: V.12B Date: 09/20/2017 Page 2 / 4 AM2520YC09 TECHNICAL DATA SPATIAL DISTRIBUTION RELATIVE INTENSITY vs. WAVELENGTH Yellow Relative Intensity (a. u.) 100% Ta = 25 °C Ta = 25 °C 80% 0° -15° 15° 30° -30° 45° -45° 60% 60° -60° 40% 20% 75° -75° 0% 350 400 450 500 550 600 Wavelength (nm) 650 700 750 800 -90° 1.0 0.5 0.0 90° 1.0 0.5 YELLOW Forward current (mA) Ta = 25 °C 40 30 20 10 1.7 1.9 2.1 2.3 Forward voltage (V) 2.5 2.5 Permissible forward current (mA) Luminous intensity normalised at 20 mA 50 0 1.5 Forward Current Derating Curve Luminous Intensity vs. Forward Current Ta = 25 °C 2.0 1.5 1.0 0.5 0.0 0 10 20 30 40 Forward current (mA) 50 REFLOW SOLDERING PROFILE for LEAD-FREE SMD PROCESS 50 Luminous Intensity vs. Ambient Temperature Luminous intensity normalised at Ta = 25 °C Forward Current vs. Forward Voltage 40 30 20 10 0 -40 -20 0 20 40 60 80 100 Ambient temperature (°C) 2.5 2.0 1.5 1.0 0.5 0.0 -40 -20 0 20 40 60 80 100 Ambient temperature (°C) TAPE SPECIFICATIONS (units : mm) REEL DIMENSION (units : mm) Notes: 1. Don't cause stress to the LEDs while it is exposed to high temperature. 2. The maximum number of reflow soldering passes is 2 times. 3. Reflow soldering is recommended. Other soldering methods are not recommended as they might cause damage to the product. © 2017 Kingbright. All Rights Reserved. Spec No: DSAD1287 / 1202000759 Rev No: V.12B Date: 09/20/2017 Page 3 / 4 AM2520YC09 PACKING & LABEL SPECIFICATIONS PRECAUTIONARY NOTES 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes © 2017 Kingbright. All Rights Reserved. Spec No: DSAD1287 / 1202000759 Rev No: V.12B Date: 09/20/2017 Page 4 / 4