APA2106ZGCK

2.1x0.6mm RIGHT ANGLE SURFACE LED LAMP ATTENTION Part Number: APA2106ZGCK Green OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Features Description z 2.1mmX0.6mm right angle SMT LED, 1.0mm thickness. The Green source color devices are made with InGaN z Low power consumption. on Sapphire Light Emitting Diode. z Wide viewing angle. Static electricity and surge damage the LEDS. z Ideal for backlight and indicator. It is recommended to use a wrist band or anti-electrostatic z Various colors and lens types available. glove when handling the LEDs. z Package: 2000pcs / reel. All devices, equipment and machinery must be electrically z Moisture sensitivity level : level 3. grounded. z Tinned pads for improved solderability. z RoHS compliant. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2.Tolerance is ±0.1(0.004") unless otherwise noted. 3.The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications SPEC NO: DSAN2342 REV NO: V.1B DATE: SEP/23/2013 PAGE: 1 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1203013862 Selection Guide Part No. Dice APA2106ZGCK Green (InGaN) Water Clear Viewing Angle [1] Iv (mcd) [2] @ 20mA Lens Type Min. Typ. 2θ1/2 200 300 120° Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%. 3. Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. λpeak Peak Wavelength Green λD [1] Dominant Wavelength Δλ1/2 Max. Units Test Conditions 515 nm IF=20mA Green 525 nm IF=20mA Spectral Line Half-width Green 35 nm IF=20mA C Capacitance Green 45 pF VF=0V;f=1MHz VF [2] Forward Voltage Green 3.3 4.1 V IF=20mA IR Reverse Current Green 50 uA VR=5V Notes: 1.Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. 3. Wavelength value is traceable to the CIE127-2007 compliant national standards. Absolute Maximum Ratings at TA=25°C Parameter Green Units Power dissipation 102.5 mW DC Forward Current 25 mA Peak Forward Current [1] 150 mA 5 V Reverse Voltage Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAN2342 REV NO: V.1B DATE: SEP/23/2013 PAGE: 2 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1203013862 GREEN Green APA2106ZGCK SPEC NO: DSAN2342 REV NO: V.1B DATE: SEP/23/2013 PAGE: 3 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1203013862 APA2106ZGCK Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension Tape Dimensions (Units : mm) SPEC NO: DSAN2342 REV NO: V.1B DATE: SEP/23/2013 PAGE: 4 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1203013862 PACKING & LABEL SPECIFICATIONS APA2106ZGCK Terms and conditions for the usage of this document 1.The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2.The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3.When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4.The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5.The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6.All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAN2342 REV NO: V.1B DATE: SEP/23/2013 PAGE: 5 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1203013862