APA3010SYC

3.0mmx1.0 mm RIGHT ANGLE SMD C HIP LED LAMP APA3010SYC SUPER BRIGHT YELLOW z3.0mmx1.0mm RIGHT ANGLE SMT LED, 2.0mm T HICKNESS. zLOW POWER CONSUMPTION. zWIDE VIEWING ANGLE. zIDEAL FOR BACK LIGHT AND INDICATOR. zPACKAGE : 2000PCS / REEL. zRoHS COMPLIANT. Features Description The Super Bright Yellow device is made with DH InGaAlP (on GaAs substrate) light emitting diode chip. zVARIOUS COLORS AND LENS TYPES AVAILABLE. Package Dimension s Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.15(0.006") unless otherwise noted. 3. Specifications are subject to change without notice. SPEC NO: DSAB1176 APPROVED: J. Lu REV NO: V.8 CHECKED: Allen Liu DATE: JUN/29/2005 DRAWN: S.H.CHEN PAGE: 1 OF 5 ERP: 1203000646 Selection Guid e Part No. Dice Lens Type Iv (mcd) @ 20mA Min. APA3010SYC SUPER BRIGHT YELLOW (InGaAlP) WATER CLEAR 36 Typ. 120 Viewing Angle 2 θ 1/2 120° Note: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value. Electrical / Optical Characteristics at TA=25°C Symbol λpeak λD ∆λ1/2 C VF IR Parameter Peak Wavelength Dominant Wavelength Spectral Line Half-width Capacitance Forward Voltage Reverse Current Device Super Bright Yellow Super Bright Yellow Super Bright Yellow Super Bright Yellow Super Bright Yellow Super Bright Yellow Typ. 590 588 28 25 2.0 2.5 10 Max. Units nm nm nm pF V uA Test Conditions IF=20mA IF=20mA IF=20mA VF=0V;f=1MHz IF=20mA VR = 5V Absolute Maximum Ratings at TA=25°C Parameter Power dissipation DC Forward Current Peak Forward Current [1] Reverse Voltage Operating/Storage Temperature Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. Super Bright Yellow 125 30 150 5 -40°C To +85°C Units mW mA mA V SPEC NO: DSAB1176 APPROVED: J. Lu REV NO: V.8 CHECKED: Allen Liu DATE: JUN/29/2005 DRAWN: S.H.CHEN PAGE: 2 OF 5 ERP: 1203000646 Super Bright Yellow APA3010SYC SPEC NO: DSAB1176 APPROVED: J. Lu REV NO: V.8 CHECKED: Allen Liu DATE: JUN/29/2005 DRAWN: S.H.CHEN PAGE: 3 OF 5 ERP: 1203000646 APA3010SYC Recommended Soldering Pattern (Units : mm) Tape Specifications (Units : mm) Remarks: If special sorting is required (e.g. binning based on forward voltage, luminous intensity, or wavelength), the typical accuracy of the sorting process is as follows: 1. Wavelength: +/-1nm 2. Luminous Intensity: +/-15% 3. Forward Voltage: +/-0.1V Note: Accuracy may depend on the sorting parameters. SPEC NO: DSAB1176 APPROVED: J. Lu REV NO: V.8 CHECKED: Allen Liu DATE: JUN/29/2005 DRAWN: S.H.CHEN PAGE: 4 OF 5 ERP: 1203000646 PACKING & LABEL SPECIFICATIONS APA3010SYC SPEC NO: DSAB1176 APPROVED: J. Lu REV NO: V.8 CHECKED: Allen Liu DATE: JUN/29/2005 DRAWN: S.H.CHEN PAGE: 5 OF 5 ERP: 1203000646