APB2012QBDCGKC

2.0x1.25mm BI-COLOR SMD CHIP LED LAMP Part Number: APB2012QBDCGKC ATTENTION Blue Green OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Features Descriptions z 2.0mmx1.25mm SMT LED, 1.1mm thickness. z The Blue source color devices are made with InGaN z Bi -color,Low power consumption. Light Emitting Diode. z The Green source color devices are made with AlGaInP z Wide viewing angle. z Ideal for backlight and indicator. on GaAs substrate Light Emitting Diode. z Electrostatic discharge and power surge could damage z Package : 2000pcs / reel. z Moisture sensitivity level : level 3. the LEDs. z It is recommended to use a wrist band or anti- z RoHS compliant. electrostatic glove when handling the LEDs. z All devices, equipments and machineries must be electrically grounded. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.15(0.006") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAM3694 REV NO: V.3B DATE: AUG/20/2014 PAGE: 1 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203013156 Selection Guide Part No. Dice Blue (InGaN) APB2012QBDCGKC Viewing Angle [1] Iv (mcd) [2] @ 20mA Lens Type Min. Typ. 40 80 20 50 Water Clear Green (AlGaInP) 2θ1/2 150° Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%. 3. Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. λpeak Peak Wavelength Blue Green λD [1] Dominant Wavelength Δλ1/2 Max. Units Test Conditions 460 574 nm IF=20mA Blue Green 465 570 nm IF=20mA Spectral Line Half-width Blue Green 25 20 nm IF=20mA C Capacitance Blue Green 100 15 pF VF=0V;f=1MHz VF [2] Forward Voltage Blue Green 3.3 2.1 V IF=20mA 4 2.5 Notes: 1.Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. 3. Wavelength value is traceable to the CIE127-2007 compliant national standards. 4.Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25°C Parameter Blue Green Units Power dissipation 120 75 mW DC Forward Current 30 30 mA Peak Forward Current [1] 150 150 mA Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAM3694 REV NO: V.3B DATE: AUG/20/2014 PAGE: 2 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203013156 APB2012QBDCGKC Blue SPEC NO: DSAM3694 REV NO: V.3B DATE: AUG/20/2014 PAGE: 3 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203013156 Green SPEC NO: DSAM3694 REV NO: V.3B DATE: AUG/20/2014 PAGE: 4 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203013156 APB2012QBDCGKC Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension Tape Dimensions (Units : mm) SPEC NO: DSAM3694 REV NO: V.3B DATE: AUG/20/2014 PAGE: 5 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203013156 PACKING & LABEL SPECIFICATIONS APB2012QBDCGKC Terms and conditions for the usage of this document 1.The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2.The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3.When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4.The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5.The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6.All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAM3694 REV NO: V.3B DATE: AUG/20/2014 PAGE: 6 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203013156