APBVDA3020SURKCGKC

3.0x2.0mm RIGHT ANGLE SMD LED Part Number: APBVDA3020SURKCGKC Hyper Red Green Features Descriptions z 3.0mmx2.0mm SMT LED,2.8mm thickness. z The Hyper Red source color devices are made with Al GaInP on GaAs substrate Light Emitting Diode. z Low power consumption. z Ideal for back light and indicator z The Green source color devices are made with AlGaInP on GaAs substrate Light Emitting Diode. z Package : 2000pcs / reel. z When soldered in the sideview configuration, the maximum shear tolerance of the epoxy lens is 300g. z Tinned pads for improved solderability. z Moisture sensitivity level : level 3. z RoHS compliant. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.2(0.008") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAJ2424 REV NO: V.3 DATE: MAY/11/2015 PAGE: 1 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1203009099 Selection Guide Part No. Dice APBVDA3020SURKCGKC Hyper Red (AlGaInP) Water Clear Green (AlGaInP) Viewing Angle [1] Iv (mcd) [2] @ 20mA Lens Type Min. Typ. 480 900 110 300 2θ1/2 15° Notes: 1. θ1 / 2 is the angle from optical centerline where the luminous intensity is 1 / 2 of the optical peak value. 2. Luminous intensity / luminous Flux: +/-15%. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. λpeak Peak Wavelength Hyper Red Green λD [1] Dominant Wavelength Δλ1/2 Max. Units Test Conditions 645 574 nm IF=20mA Hyper Red Green 630 570 nm IF=20mA Spectral Line Half-width Hyper Red Green 28 20 nm IF=20mA C Capacitance Hyper Red Green 35 15 pF VF=0V;f=1MHz VF [2] Forward Voltage Hyper Red Green 1.95 2.1 2.5 2.5 V IF=20mA IR Reverse Current Hyper Red Green 10 10 uA VR = 5V Notes: 1. Wavelength: + / -1nm. 2. Forward Voltage: + / -0.1V. 3. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25°C Parameter Hyper Red Green Units Power dissipation 75 75 mW DC Forward Current 30 30 mA Peak Forward Current [1] 185 150 mA Reverse Voltage 5 V Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C Note: 1. 1 / 10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAJ2424 REV NO: V.3 DATE: MAY/11/2015 PAGE: 2 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1203009099 APBVDA3020SURKCGKC Hyper Red SPEC NO: DSAJ2424 REV NO: V.3 DATE: MAY/11/2015 PAGE: 3 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1203009099 Green SPEC NO: DSAJ2424 REV NO: V.3 DATE: MAY/11/2015 PAGE: 4 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1203009099 APBVDA3020SURKCGKC Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension Tape Dimensions (Units : mm) SPEC NO: DSAJ2424 REV NO: V.3 DATE: MAY/11/2015 PAGE: 5 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1203009099 PACKING & LABEL SPECIFICATIONS APBVDA3020SURKCGKC Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAJ2424 REV NO: V.3 DATE: MAY/11/2015 PAGE: 6 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1203009099