APG1005SEC-T

1.0X0.5X0.2mm (0402)SMD CHIP LED LAMP Part Number: APG1005SEC-T Super Bright Orange Features Description z 1.0mmX0.5mm SMD LED, 0.2mm thickness. The Super Bright Orange source color devices are made z Low power consumption. with AlGaInP on GaAs substrate Light Emitting Diode. z Wide viewing angle. z Compatible with automatic placement equipment. z Ideal for backlight and indicator. z Package: 4000pcs / reel. z Moisture sensitivity level : level 3. z RoHS compliant. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.1(0.004") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAM9855 REV NO: V.5A DATE: JUL/01/2016 PAGE: 1 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.T.Zhang ERP: 1203013779 Selection Guide Part No. Emitting Color (Material) Lens Type Super Bright Orange (AlGaInP) APG1005SEC-T Water Clear Iv (mcd) [2] @ 20mA Viewing Angle [1] Min. Typ. 55 153 *40 *90 2θ1/2 120° Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%. * Luminous intensity value is traceable to CIE127-2007 standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Emitting Color Typ. λpeak Peak Wavelength Super Bright Orange λD [1] Dominant Wavelength Δλ1/2 Max. Units Test Conditions 611 nm IF=20mA Super Bright Orange 605 nm IF=20mA Spectral Line Half-width Super Bright Orange 17 nm IF=20mA VF [2] Forward Voltage Super Bright Orange 2.05 2.4 V IF=20mA IR Reverse Current Super Bright Orange 10 uA VR=5V Notes: 1.Wavelength: +/-1nm. 2.Forward Voltage: +/-0.1V. 3.Wavelength value is traceable to CIE127-2007 standards. 4.Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25°C Parameter Values Units Power dissipation 60 mW DC Forward Current 25 mA Peak Forward Current [1] 120 mA 5 V Reverse Voltage Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C Notes: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. 2. Relative humidity levels maintained between 40% and 60% in production area are recommended to avoid the build-up of static electricity – Ref JEDEC/JESD625-A and JEDEC/J-STD-033. SPEC NO: DSAM9855 REV NO: V.5A DATE: JUL/01/2016 PAGE: 2 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.T.Zhang ERP: 1203013779 Super Bright Orange APG1005SEC-T SPEC NO: DSAM9855 REV NO: V.5A DATE: JUL/01/2016 PAGE: 3 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.T.Zhang ERP: 1203013779 APG1005SEC-T Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension Mask open area ratio:80% Mask thickness:80~100um Tape Dimensions (Units : mm) SPEC NO: DSAM9855 REV NO: V.5A DATE: JUL/01/2016 PAGE: 4 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.T.Zhang ERP: 1203013779 PACKING & LABEL SPECIFICATIONS APG1005SEC-T Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAM9855 REV NO: V.5A DATE: JUL/01/2016 PAGE: 5 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.T.Zhang ERP: 1203013779