APJA2107SURC

2.1x0.7 mm RIGHT ANGLE SMD CHIP LED LAMP APJA2107SURC HYPER RED Features 2.1mmx0.7mm RIGHT ANGLE SMT LED, 1.3mm THICKNESS. LOW POWER CONSUMPTION. WIDE VIEWING ANGLE. IDEAL FOR BACKLIGHT AND INDICATOR. VARIOUS COLORS AND LENS TYPES AVAILABLE. PACKAGE : 2000PCS / REEL. RoHS COMPLIANT. Description The Hyper Red source color devices are made with DH InGaAlP on GaAs substrate Light Emitting Diode. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ± 0 .15(0.006") unless otherwise noted. 3. Specifications are subject to change without notice. S PEC NO: DSAD1025 APPROVED: J. Lu REV NO: V.5 CHECKED: Allen Liu DATE: JUN/29/2005 DRAWN: H.Q.YUAN PAGE: 1 OF 5 ERP:1203001551 Selection Guide Part No. Dice Lens Type Iv (mcd) @ 20mA Min. APJA2107SURC HYPER RED (InGaAlP) WATER CLEAR 70 Typ. 200 Viewing Angle 2θ1/2 120° Note: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value. Electrical / Optical Characteristics at TA=25°C Symbol λpeak λD ∆λ1/2 C VF IR Parameter Peak Wavelength Dominant Wavelength Spectral Line Half-width Capacitance Forward Voltage Reverse Current Device Hyper Red Hyper Red Hyper Red Hyper Red Hyper Red Hyper Red Typ. 640 628 27 45 1.9 2.5 10 Max. Units nm nm nm pF V uA Test Conditions IF=20mA IF=20mA IF=20mA VF=0V;f=1MHz IF=20mA VR = 5V Absolute Maximum Ratings at TA=25°C Parameter Power dissipation DC Forward Current Peak Forward Current [1] Reverse Voltage Operating/Storage Temperature Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. Hyper Red 170 30 185 5 -40°C To +85°C Units mW mA mA V S PEC NO: DSAD1025 APPROVED: J. Lu REV NO: V.5 CHECKED: Allen Liu DATE: JUN/29/2005 DRAWN: H.Q.YUAN PAGE: 2 OF 5 ERP:1203001551 Hyper Red APJA2107SURC S PEC NO: DSAD1025 APPROVED: J. Lu REV NO: V.5 CHECKED: Allen Liu DATE: JUN/29/2005 DRAWN: H.Q.YUAN PAGE: 3 OF 5 ERP:1203001551 APJA2107SURC Recommended Soldering Pattern (Units : mm) Tape Specifications (Units : mm) Remarks: If special sorting is required (e.g. binning based on forward voltage, luminous intensity, or wavelength), the typical accuracy of the sorting process is as follows: 1. Wavelength: +/-1nm 2. Luminous Intensity: +/-15% 3. Forward Voltage: +/-0.1V Note: Accuracy may depend on the sorting parameters. S PEC NO: DSAD1025 APPROVED: J. Lu REV NO: V.5 CHECKED: Allen Liu DATE: JUN/29/2005 DRAWN: H.Q.YUAN PAGE: 4 OF 5 ERP:1203001551 PACKING & LABEL SPECIFICATIONS APJA2107SURC S PEC NO: DSAD1025 APPROVED: J. Lu REV NO: V.5 CHECKED: Allen Liu DATE: JUN/29/2005 DRAWN: H.Q.YUAN PAGE: 5 OF 5 ERP:1203001551